4RF Aprisa SR Manuals

September 2018 Version 1.3.0

Aprisa SR+ Quick Start Guide 1.4.0 © 2018 4RF Limited. All rights reserved. This document is protected by copyright belonging to 4RF Limited and may not be reproduced or republished in whole or part in any form without the prior written permission of 4RF Limited. While every precaution has been taken in the preparation of this literature, 4RF Limited assumes no liability or errors and omissions, or from any damages resulting from use of this information. The contents and any product specifications within it are subject to revision due to ongoing product improvements and may change without notice. Aprisa and the 4RF logo are trademarks of 4RF Limited. All other marks are the property of their respective owners. 5. Set up the Aprisa SR+ radio The Aprisa SR+ has a factory default Terminal Operating Mode of Remote Station. One radio in the Aprisa SR+ network must be setup as a Base Station. The other radios in the Aprisa SR+ network are setup as Remote Stations or Repeater Stations. Set the Ethernet Operating Mode. Set the unique radio Network ID to be the same in your entire network including the Base Station ID. Set the Aprisa SR+ TX Frequency, RX Frequency, TX Power and Channel Size to comply with your site license. Set the Antenna Port Configuration required. You can now configure the remaining terminal and network parameters and settings. Please refer to the Aprisa SR+ User Manual for detailed instructions. For ACM implementations, we recommend that the Default Modulation be set to QPSK (Low Gain). 6. Monitor the Aprisa SR+ radio signal strength When the network is installed, the radio signal strength can be monitored on remote stations by setting the radio to Test Mode. To enter Test Mode, press and hold the TEST button on the radio LED panel until all the LEDs flash green (about 3 - 5 seconds). In Test Mode, the LED Display panel presents a real time visual display of the RSSI. This can be used to adjust the antenna for optimum signal strength. Note: The response time is variable and can be up to 5 seconds. To exit Test Mode, press and hold the TEST button until all the LEDs flash red (about 3 - 5seconds). The OK, MODE and AUX LEDs will be solid green and the TX and RX LEDs will be solid or flash green if the network is operating correctly. For more information, please refer to the Aprisa SR+ User Manual available from the 4RF website www.4rf.com/secure/ (login required). Quick Start Guide Aprisa SR+ Radio Contents Follow these steps to operate your Aprisa SR+ radio: 1. Check the box contents 2. Install the Aprisa SR+ radio and connect the protection earth 3. Connect the Antenna and apply power to the Aprisa SR+ radio 4. Connect to the Aprisa SR+ radio 5. Set up the Aprisa SR+ radio 6. Monitor the Aprisa SR+ radio signal strength

April 2013 Version 1.0.0.03 (for General Availability Release in October 2013)

Aprisa SR+ Migration Station Quick Start Guide 1.2.0 © 2021 4RF Limited. All rights reserved. This document is protected by copyright belonging to 4RF Limited and may not be reproduced or republished in whole or part in any form without the prior written permission of 4RF Limited. While every precaution has been taken in the preparation of this literature, 4RF Limited assumes no liability or errors and omissions, or from any damages resulting from use of this information. The contents and any product specifications within it are subject to revision due to ongoing product improvements and may change without notice. Aprisa and the 4RF logo are trademarks of 4RF Limited. All other marks are the property of their respective owners. 5. Setup the Aprisa SR+ Migration Station Login using the IP address of either the primary or secondary radio (do not use the PVIP address for login). All parameters will be automatically synchronized on both radios. The Aprisa SR+ has a factory default Terminal Operating Mode of Remote Station. A single radio or a Migration Station in the Aprisa SR+ network must be setup as a base station. The other radios or Migration Stations in the Aprisa SR+ network are setup as remote stations or repeater stations. Set the Ethernet Operating Mode and the Compliance Mode required. Set the unique radio Network ID to be the same in your entire network including the Base Station ID. Set the Aprisa SR+ TX Frequency, RX Frequency, TX Power and Channel Size to comply with your site license. Set the Antenna Port Configuration required. You can now configure the remaining Migration Station and network parameters and settings. For more information, please refer to the ‘Aprisa SR+ User Manual Appendix 1 - Migration Station’ available from the 4RF website https://www.4rf.com/secure (login required). Reboot both Primary and Secondary radios and restore the Hardware Manual Lock switch is set to AUTO. The Aprisa SR+ Migration Station is ready to operate. 6. Monitor the Aprisa SR+ Migration Station signal strength When the network is installed, the radio signal strength can be monitored on remote stations by setting the radio to Test Mode. To enter Test Mode, press and hold the TEST button on front panel until all the LEDs flash green (about 3 - 5 seconds). In Test Mode, the LED Display panel presents a real time visual display of the RSSI. This can be used to adjust the antenna for optimum signal strength. Note: The response time is variable and can be up to 5 seconds. To exit Test Mode, press and hold the TEST button until all the LEDs flash red (about 3 - 5seconds). If the network is operating correctly, the LEDs will show: • Active radio - the OK, MODE and AUX LEDs will be light green and the TX and RX LEDs will be solid or flash green. • Standby radio - the OK will light green, the MODE LED will light orange, the AUX LED will light green and the TX and RX LEDs will light green (steady). Quick Start Guide Aprisa SR+ Migration Station Contents Follow these steps to setup your Aprisa SR+ Migration Station: 1. Check the box contents 2. Install the Aprisa SR+ Migration Station and connect the protection earths 3. Connect the antenna and apply power to the Aprisa SR+ Migration Station 4. Connect to the Aprisa SR+ Migration Station 5. Set up the Aprisa SR+ Migration Station 6. Monitor the Aprisa SR+ Migration Station signal strength

Aprisa SR+ Protected Station Quick Start Guide 1.4.0 © 2021 4RF Limited. All rights reserved. This document is protected by copyright belonging to 4RF Limited and may not be reproduced or republished in whole or part in any form without the prior written permission of 4RF Limited. While every precaution has been taken in the preparation of this literature, 4RF Limited assumes no liability or errors and omissions, or from any damages resulting from use of this information. The contents and any product specifications within it are subject to revision due to ongoing product improvements and may change without notice. Aprisa and the 4RF logo are trademarks of 4RF Limited. All other marks are the property of their respective owners. 5. Set up the Aprisa SR+ Protected Station Login using the IP address of either the primary or secondary radio (do not use the PVIP address for login). All parameters will be automatically synchronized on both radios. The Aprisa SR+ has a factory default Terminal Operating Mode of Remote Station. A single radio or a protected station in the Aprisa SR+ network must be setup as a base station. The other radios or protected stations in the Aprisa SR+ network are setup as remote stations or repeater stations. Set the Ethernet Operating Mode and the Compliance Mode required. Set the unique radio Network ID to be the same in your entire network including the Base Station ID. Set the Aprisa SR+ TX Frequency, RX Frequency, TX Power and Channel Size to comply with your site license. Set the Antenna Port Configuration required. You can now configure the remaining protected station and network parameters and settings. For more information, please refer to the Aprisa SR+ User Manual available from the 4RF website https://www.4rf.com/secure (login required). Reboot both Primary and Secondary radios and restore the Hardware Manual Lock switch is set to AUTO. The Aprisa SR+ Protected Station is ready to operate. 6. Monitor the Aprisa SR+ Protected Station signal strength When the network is installed, the radio signal strength can be monitored on remote stations by setting the radio to Test Mode. To enter Test Mode, press and hold the TEST button on front panel until all the LEDs flash green (about 3 - 5 seconds). In Test Mode, the LED Display panel presents a real time visual display of the RSSI. This can be used to adjust the antenna for optimum signal strength. Note: The response time is variable and can be up to 5 seconds. To exit Test Mode, press and hold the TEST button until all the LEDs flash red (about 3 - 5seconds). If the network is operating correctly, the LEDs will show: • Active radio - the OK, MODE and AUX LEDs will be light green and the TX and RX LEDs will be solid or flash green. • Standby radio - the OK will light green, the MODE LED will light orange, the AUX LED will light green and the TX and RX LEDs will light green (steady). Quick Start Guide Aprisa SR+ Protected Station Contents Follow these steps to setup your Aprisa SR+ Protected Station: 1. Check the box contents 2. Install the Aprisa SR+ protected station and connect the protection earth 3. Connect the antenna and apply power to the Aprisa SR+ protected station 4. Connect to the Aprisa SR+ protected station 5. Set up the Aprisa SR+ protected station 6. Monitor the Aprisa SR+ protected station signal strength

February 2013 Version 1.5.3a

This User Manual refers to the new Aprisa SR (part number SRx) February 2015 Version 1.3.0

Rhein Tech Laboratories, Inc. Client: 4RF Communications 360 Herndon Parkway Model: Aprisa SR SRN400-000 Suite 1400 FCC ID: UIPSRN0400012A Herndon, VA 20170 Standards: FCC Part 90 http://www.rheintech.com Report #: 2011198 Page 34 of 40 Appendix J: Manual Please refer to the following pages.

November 2015 Version 1.5.3

January 2021 Version 1.11.1b