A&D FC-50Ki Manuals

ふ Counting Scale FC-50Ki FC-5000Si FC-20Ki FC-500Si FC-10Ki FC-5000i FC-2000i FC-1000i FC-500i WM+PD4000541B This manual and Marks All safety messages are identified by the following, “WARNING” or “CAUTION”, of ANSI Z535.4 (American National Standard Institute: Product Safety Signs and Labels). The meanings are as follows: WARNING A potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION A potentially hazardous situation which, if not avoided, may result in minor or moderate injury. This is a hazard alert mark. This mark informs you about the operation of the product. The information mark of other operations. Note This manual is subject to change without notice at any time to improve the product. No part of this manual may be photocopied, reproduced, or translated into another language without the prior written consent of the A&D Company. Product specifications are subject to change without any obligation on the part of the manufacture. Compliance with FCC rules Please note that this equipment generates, uses and can radiate radio frequency energy. This equipment has been tested and has been found to comply with the limits of a Class A computing device pursuant to Subpart J of Part 15 of FCC rules. These rules are designed to provide reasonable protection against interference when this equipment is operated in a commercial environment. If this unit is operated in a residential area it might cause some interference and under these circumstances the user would be required to take, at his own expense, whatever measures are necessary to eliminate the interference. (FCC = Federal Communications Commission in the U.S.A.) Copyright 2003 Contents 1. INTRODUCTION ...........................................................................................................3 1-1. Introduction..............................................................................................................................3 1-2. Unpacking ...............................................................................................................................4 1-3. Setting Up Your Scale .............................................................................................................5 1-4. Standby and Operating Mode..................................................................................................7 1-5. Simple Operation Mode...........................................................................................................7 1-6. kg or lb Weighing Units ...........................................................................................................7 1-7. Last Unit Weight Used Feature ...............................................................................................8 2. FRONT PANEL OVERVIEW .........................................................................................9 3. BASIC OPERATIONS .................................................................................................10 3-1. Basic Operations...................................................................................................................10 3-2. To Start Counting...................................................................................................................12 3-3. Unit Weight By Samples........................................................................................................13 3-4. Unit Weight By KEYBOARD..................................................................................................17 3-5. Unit Weight By ID Number ....................................................................................................18 4. ENTERING A TARE WEIGHT .....................................................................................19 4-1. Using the KEYBOARD TARE Key.........................................................................................19 4-2. To Clear TARE.......................................................................................................................20 5. STORE UNIT WEIGHT................................................................................................21 5-1. Store Unit Weight by ID Number ...........................................................................................21 5-2. Clearing A Stored Unit Weight...............................................................................................22 5-3. Store Item Code by ID Number .............................................................................................23 5-4. Unit Weight, Tare, Comparator Limits & Total Count Stored ...........................................................25 6. USING THE M+ MEMORY ..........................................................................................26 6-1. The M+ Memory Function .....................................................................................................26 6-2. Viewing the M+ Total .............................................................................................................27 6-3. Clearing the M+ Total ............................................................................................................27 6-4. The M- Function ....................................................................................................................27 7. COMPARATOR FUNCTION........................................................................................28 8. TIME AND DATE FUNCTION......................................................................................30 9. CALIBRATION ............................................................................................................31 1 ©A&D Co.ltd., FC-i Instruction manual International version 23783AIE0309 9-1. Calibration Procedure Using a Weight ..................................................................................31 9-2. Gravity Compensation...........................................................................................................33 10. F-FUNCTION PARAMETERS....................................................................................34 10-1. To Change or View F-Function Settings.............................................................................34 10-2. F-Functions........................................................................................................................36 11. ACAI FUNCTION.......................................................................................................44 11-1. ACAI Automatic Counting Accuracy Improvement ........................................................44 11-2. ACAI Automatic Operation.................................................................................................44 11-3. ACAI Manual Operation.....................................................................................................45 12. RS-232C SERIAL INTERFACE .................................................................................46 12-1. RS-232C Specifications .....................................................................................................46 12-2. Data Output Mode..............................................................................................................47 12-3. Connecting the AD-8121 Printer / MODE 1 or MODE 2.....................................................48 12-4. Connecting the AD-8121 Printer / MODE 3........................................................................49 12-5. Command Mode ................................................................................................................50 12-6. Using a Bar Code Reader..................................................................................................55 12-7. Using UFC (Universal Flex Coms) Function ......................................................................59 13. OPTIONS ...................................................................................................................62 13-1. OP-01 Bar Code Reader....................................................................................................62 13-2. OP-02 Ni-MH Battery Pack................................................................................................65 13-3. OP-03 2 Ch. RS-232C .......................................................................................................67 13-4. OP-04 RS-232C and Comparator Relay Output................................................................68 13-5. OP-05 Remote Scale Interface ..........................................................................................69 14. SPECIFICATIONS .....................................................................................................73 14-1. Dimensions ........................................................................................................................75 15. GRAVITY ACCELERATION MAP..............................................................................76 16. INDEX ........................................................................................................................78 2

ふ Counting Scale FC-50Ki FC-20Ki FC-10Ki FC-5000i WM : PD4000541 This manual and Marks All safety messages are identified by the following, “WARNING” or “CAUTION”, of ANSI Z535.4 (American National Standard Institute: Product Safety Signs and Labels). The meanings are as follows: WARNING A potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION A potentially hazardous situation which, if not avoided, may result in minor or moderate injury. This is a hazard alert mark. This mark informs you about the operation of the product. The information mark of another operations. Note This manual is subject to change without notice at any time to improve the product. No part of this manual may be photocopied, reproduced, or translated into another language without the prior written consent of the A&D Company. Product specifications are subject to change without any obligation on the part of the manufacture. Compliance with FCC rules Please note that this equipment generates, uses and can radiate radio frequency energy. This equipment has been tested and has been found to comply with the limits of a Class A computing device pursuant to Subpart J of Part 15 of FCC rules. These rules are designed to provide reasonable protection against interference when this equipment is operated in a commercial environment. If this unit is operated in a residential area it might cause some interference and under these circumstances the user would be required to take, at his own expense, whatever measures are necessary to eliminate the interference. (FCC = Federal Communications Commission in the U.S.A.) Copyright 2003 1 Contents 1. INTRODUCTION..............................................................................................................3 1-1. Unpacking..................................................................................................................3 1-2. Setting Up Your Scale................................................................................................3 1-3. Standby and Operating Mode ....................................................................................5 1-4. Simple Operation Mode .............................................................................................5 1-5. kg or lb Weighing Units..............................................................................................5 1-6. Last Unit Weight Used Feature..................................................................................6 Front Panel Overview ........................................................................................................7 2. BASIC OPERATIONS......................................................................................................8 2-1. Basic Operations .......................................................................................................8 2-2. To Start Counting .....................................................................................................10 2-3. Unit Weight By Samples ..........................................................................................11 2-4. Unit Weight By KEYBOARD ....................................................................................15 2-5. Unit Weight By ID Number.......................................................................................16 3. ENTERING A TARE WEIGHT .......................................................................................17 3-1. Using the KEYBOARD TARE Key ...........................................................................17 3-2. To Clear TARE .........................................................................................................18 4. STORE UNIT WEIGHT ..................................................................................................19 4-1. Store Unit Weight by ID Numbers ............................................................................19 4-2. Clearing A Stored Unit Weight..................................................................................20 4-3. Store Item Code by ID Number................................................................................21 4-4. Unit Weight, Tare, Comparator Limits & Total Count Stored.............................................23 5. USING THE M+ MEMORY.............................................................................................24 5-1. The M+ Memory Function........................................................................................24 5-2. Viewing the M+ Total................................................................................................25 5-3. Clearing the M+ Total...............................................................................................25 5-4. The M- Function.......................................................................................................25 6. COMPARATOR FUNCTION ..........................................................................................26 7. TIME AND DATE FUNCTION........................................................................................28 8. CALIBRATION...............................................................................................................29 8-1. Calibration Procedure Using a Weight.....................................................................29 8-2. Gravity Compensation .............................................................................................31 9. F-FUNCTION PARAMETERS .......................................................................................32 9-1. To Change or View F-Function Settings...................................................................32 9-2. F-Functions..............................................................................................................33 10. ACAI FUNCTION.........................................................................................................40 10-1. ACAI Automatic Counting Accuracy Improvement.............................................40 2 10-2. ACAI Automatic Operation .....................................................................................40 10-3. ACAI Manual Operation .........................................................................................41 11. RS-232C SERIAL INTERFACE ...................................................................................42 11-1. RS-232C Specifications .........................................................................................42 11-2. Data Output Mode..................................................................................................43 11-3. Connecting the AD-8121 Printer / MODE 1 or MODE 2.........................................44 11-4. Connecting the AD-8121 Printer / MODE 3............................................................44 11-5. Command Mode.....................................................................................................45 12. OPTIONS.....................................................................................................................51 12-1. OP-02 Ni-MH Battery Pack....................................................................................51 12-2. OP-03 2 Ch. RS-232C ...........................................................................................52 12-3. OP-04 RS-232C and Comparator Relay Output ....................................................53 12-4. OP-05 Remote Scale Interface ..............................................................................54 13. SPECIFICATIONS .......................................................................................................58 14. GRAVITY ACCELERATION MAP................................................................................59