ADTRAN BVL3AH1D Series Manuals

jobAid 1 DESCRIPTION The Small Form-Factor Pluggable 9.95 - 11.3G, Single-Mode 20 km (SFP+) optical transceiver is a fully duplex serial electric, serial optical device with both transmit and receive functions contained in a single module that provides a high speed serial link of up to 11.3 Gbs. Installed into an appropriate host module, the SFP+ provides an 11.3 Gigabit interface to the supporting system. The transmit side of the SFP+ converts serial NRZ electrical data at the 11.3 Gbs line rate to a standard compliant optical signal. The receive side of the SFP+ converts the incoming DC balanced serial NRZ optical data at the 11.3 Gbs line rate into serial electrical data. The following features are supported on the SFP+: ■1310 nm optical signals for up to 20 km reach ■Case temperature hardened range from –40°C to 85°C ■Low power consumption (<1.5 W max) ■Bit error rate (<1x10-12) ■Excellent EMI performance CAUTION ! Due to compliance certification requirements, use only SFP+s supplied by ADTRAN with the host module. ADTRAN cannot certify system integrity with other SFP+s. Operational Specifications ■Optical Specifications: ♦1310 nm optical signals for up to 20 km reach ♦Data rate: 9.953 to 11.3 Gbs ♦Optical transmit level: –5.0 to +1.5 dBm ♦Optical receive level sensitivity: –12.6 dBm (+0.5) ♦Optical distance: 20 km maximum ♦Optical connectors: LC ■Extended Environmental Support: ♦Operational temperature range: –40°C to +85°C ♦Storage temperature range: –40°C to +85°C ♦Relative humidity to 85%, noncondensing Small Form-Factor Pluggable 9.95 - 11.3G, Single-Mode, 20 km, SFP+ INSTALLATION Before installing the equipment, inspect the SFP+. If damage has occurred during shipping, file a claim with the carrier, and then contact ADTRAN Customer Support. For more information, refer to the warranty. Installation Guidelines The following are guidelines for this installation: ■Do not remove the protective end cap from the SFP+ until the fiber optic cable is ready to be connected. ■The latch on the SFP+ is for removal only. When removing the SFP+, rotate the latch away from the SFP+, the SFP+ should easily slide out of the cage. ■Ensure that the protective end cap remains on whenever the transceiver optical fiber connector is not inserted. Installation Steps To install the SFP+ into an appropriate module, complete the following steps: 1. Insert the SFP+ into the cage on the module. Ensuring that the latch handle on the SFP+ is facing upward, slide the SFP+ all the way into the SFP+ cage until there is an audible “click”. 2. Do not remove the protective end cap until the optical fiber connection is made. 3. Continue the installation and turn-up of the host module using the instructions in the Job Aid provided with the module or other system-level documentation available online at www.adtran.com. PROVISIONING The SFP+ is not provisionable. For configuration or status infor- mation, access the menu system of the host module. Refer to the “Provisioning” section of the host module documentation for provisioning details. MAINTENANCE The SFP+ does not require routine hardware maintenance for normal operation. Repair services may be obtained by returning the defective unit to ADTRAN. Refer to the warranty for further information. CLEI: BVL3AH1D_ _ Product P/N: 1442420G1 Issue Date: February 2015 Document P/N: 61442420G1-22C Documentation for ADTRAN Carrier Networks products is available for viewing and download directly from the ADTRAN Support Community website. Go to: https://supportforums.adtran.com/welcome Registration is required. ADTRAN offers training courses on our products, including customized training and courses taught at our facilities or at customer sites. For inquiries, go to: http://adtran.com/training The following related online documents and resources provide additional information for this product: SFP/XFP/SFP+ Compatibility Matrix (Online Tool: www.adtran.com/SFP)