Advantech-DLoG DLT-U1100 Manuals

1 Mounting by electronic and mechanical skilled persons Quickstart DLT-U1100 2 Important notes Personal injury Explosion hazard The following icons are used in this quick start guide to indicate dangers: NOTICE Risk of physical damage 3 Technical data Battery Lithium-ion battery Bridging time 10 min Maximum output 40 W Nominal output voltage of the UPS 12 VDC Nominal input voltage of the UPS 12, 24, 48 VDC Input voltage range 9 to 60 VDC Output voltage range 10 to 14 VDC Charging time 2,5 h (fully recharge a completely discharged battery) Connector input Lumberg 0315 04-Pin male Connector output Lumberg 0305 04-Pin female Qualifications required for mounting of the UPS DLT-U1100 This Quickstart Poster will show you how to perform the mechanical and electrical mounting of the Uninterruptible Power Supply (UPS) DLT-U1100. It is intended for skilled persons. WARNING: Electric shock due to contact with live parts / property damage •� Only electronic and mechanical skilled persons are permitted to install the DLT-U1100. Specialized knowledge of batteries and the applicable safety regulations is also required. •� Unauthorized persons must be kept away from the UPS which contains rechargeable Lithium Ion batteries. •� If�the�DLT-U1100�is�incorrectly�installed�and�configured,�the�DLoG�GmbH�warranty for this device will be canceled. •� DLoG�GmbH�assumes�no�liability�for�damages�caused�directly�or�indirectly� by the incorrect installation or usage of the DLT-U1100. •� DLT-U1100 operators must be trained. Current manuals on the internet The current DLT-U1100 manuals can always be found in our Download Center on the internet www.advantech-dlog.com (Download menu). Intended use The�DLT-U1100�is�a�battery-operated�uninterruptible�power�supply�for�the�Advantech-DLoG� industrial PCs MTC 6 and XMT 5, each with 12/24 VDC power supply unit. If the DLT-U1100 is connected, MTC 6 and XMT 5 cannot be started or shut down automati- cally via vehicle ignition. NOTICE: No combination of UPS + automatic start/shut down via ignition possible MTC 6 and XMT 5 can be used with automatic startup/shut down capabilities. This automatic feature controls the startup and shutdown of the industrial PC via the button or the vehicle’s ignition. If the DLT-U1100 is connected, MTC 6 and XMT 5 cannot be started or shut down via vehicle ignition Hence�it�is�important�to�make�the�following�setting�before the DLT-U1100 is connected to MTC 6 and XMT 5: •� Define�that�the�MTC�6�and�XMT�5�always�start�and�shut�down�with�the� button, not via ignition signal. •� Make�the�respective�adjustments�in�the�configuration�tools: ���“DLoG�Config“�for�MTC�6,�“DLoG�NextConfig“�for�XMT�5 Otherwise, MTC 6 and XMT 5 can not be started, because with a connected UPS system no ignition signal is available. WARNING: Vehicle “EMERGENCY Stop Switch” cannot switch off industrial PCs with UPS If an MTC 6 or XMT 5 industrial PC with an uninterruptible power supply (UPS) is installed on a vehicle, the vehicle emergency stop switch will not affect the the industrial PC. WARNING: Explosion hazard •� Do�not�use�the�DLT-U1100�at�locations�where�flammable�gases�or�vapors�are present. •� Do not use the DLT-U1100 near gas stations, fuel depots, chemical facilities or locations where blasting work is being performed. •� Do�not�throw�the�DLT-U1100�into�fire;�the�batteries�may�explode. WARNING: Electrical shock possible from touching live parts / property damage •� Do not commission the DLT-U1100 if there are visible signs of damage to the device. •� The DLT-U1100 contains Lithium Ion batteries. Replacement of the rechargeable batteries by the customer is expressly prohibited. •� Do not open or modify the DLT-U1100. •� Do not perform any repairs. Repairs on the DLT-U1100 may be made only by ���Service�Centers�authorized�by�Advantech-DLoG. •� Do not submerge the DLT-U1100 and cables in water or other liquids because of the danger of electrical shock. •� Use�only�original�power�cables�by�Advantech-DLoG;�they�meet�special� ���requirements�for�low-temperature�flexibility,�UV�resistance,�oil�resistance,�etc. •� Condensation can occur if the DLT-U1100 is moved from a cold environment into a work room. Therefore, allow for an acclimatization time of approx. 2 hours. Temperature range, in which the UPS supplies the industrial PC with power from the battery -10 to +50 °C (+14 to +122 °F) Temperature range, in which the batteries of the UPS are recharged 0 to +45 °C (+32 to +113 °F) Storage temperature range -20 to +60 °C (-4 to +140 °F) Vibration/shock Class 5M3 according to DIN EN 60721-3-5 IP protection IP65 Weight 1.1 kg Warranty DLT-U1100 device (batteries excluded) As�specified�in�Advantech-DLoG�TOB Warranty batteries Six (6) months from delivery Any other or additional use is not as intended. The user/operator of the DLT-U1100 is solely respon- sible for any resulting damage. This also applies to unauthorized�modifications�to�the�unit.