Advantech PCM-4825 Manuals

PCM-4825/4825L Startup Manual 1 Packing List Packing List Packing List Packing List Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 PCM-4825/4825L all-in-one single board computer • 1 start-up manual • 1 audio cable (PCM-4825 only) • 1 3.5" IDE flat cable • 1 keyboard/mouse cable • 1 secondary serial port cable (RS-232/422/485) • 1 parallel cable • 1 floppy cable • CD-ROM or disks for utility, drivers, and manual (in PDF format) If any of these items are missing or damaged, contact your distributor or sales representative immediately. Note: For detailed information on the PCM-4825/4825L, please refer to the enclosed CD-ROM or disk (in PDF format). PCM-4825/4825L 486 SBC with VGA/LCD and Audio Startup Manual PCM-4825 486 SBC with VGA/LCD and Audio For more information on this and other Advantech products, please visit our website at: http://www.advantech.com http://www.advantech.com/epc For technical support and service, please visit our support website at: http://support.advantech.com This manual is for the PCM-4825/4825L Rev. A1 or higher. Part No. 2006482501 1st edition Printed in Taiwan Aug. 1999 Specifications Specifications Specifications Specifications Specifications Standard SBC Functions • CPU: Embedded AMD 5x86-133 (DX5-133) processor • BIOS: Award 128 KB Flash memory • Chipset: VIA VT82C496G • System memory: One 72-pin SIMM sockets (accepts 1/2/4/8/16/32 MB) and supports FPM or EDO DRAM 1 ~ 32 MB • Enhanced IDE hard disk drive interface: Supports up to two IDE (VL-bus) hard disks. BIOS auto- detect and PIO Mode 3 transfer protocol • Serial ports: One serial RS-232 port, one serial RS- 232/422/485 port. Two 16550 serial UARTs • Parallel port: One parallel port, supports SPP/EPP/ ECP mode • Infrared port: Shared with COM2. Transfer rate up to 115 Kbps • Keyboard/mouse connector: Mini-DIN connector supports a standard PC/AT keyboard and a PS/2 mouse • Power management: Supports power saving modes including Normal/Standby/Suspend modes. APM 1.1 compliant Local-bus Flat Panel/VGA Interface • Chipset: C&T 65550 • Display memory: 1 MB DRAM • Display type: Supports CRT and flat panel (EL, LCD, and gas plasma flat panel) displays. Simultaneous display of CRT and flat panel possible • Flat panel display mode: Up to 800 x 600 @ 256 colors • CRT display mode: Non-interlaced CRT monitors resolutions up to 1280 x 1024 @16 colors Audio Function (PCM-4825 only) • Chipset: ESS 1868/1869 • Audio controller: 16-bit Sound Blaster Pro compatible • Stereo sound: Full-duplex, integrated 3D audio • Audio interface: Mic in, Line in, CD audio in, Line out, Stereo speaker out Mechanical and Environmental • Dimension (L x W): 145 mm x 102 mm (5.9" x 4.2") • Power supply voltage: +5 V (4.75 ~ 5.25 V) • Power requirements: +5 V @ 2 A (typical) • Operating temperature: 0 ~ 60° C (32° ~ 140° F) • Weight: 0.65 kg (weight of total package) all-guides com 2 PCM-4825/4825L Startup Manual The board has a number of jumpers that allow you to configure your system to suit your application. The table below lists the function of each of the board jumpers and connectors: Jumpers Label Function J2 DOC® 2000 address setting J3 LCD power selector J4 Clear CMOS J5 Audio AMP power selector J7 COM2 selector Connectors Label Function CN1 Power connector (-5 V, -12 V) CN2 Floppy disk connector CN3 PC/104 connector CN4 Parallel port connector CN5 PC/104 connector CN6 Flat panel connector CN7 Hard disk connector CN8 IR connector (infrared) CN9 COM2 connector CN10 CD audio in connector CN11 Audio connector CN12 Power connector (+5 V, +12 V) CN13 COM1 connector CN14 PS/2 keyboard & PS/2 mouse connector CN15 CRT display connector J6 Reset switch Jumpers and Connectors Jumpers and Connectors Jumpers and Connectors Jumpers and Connectors Jumpers and Connectors Jumper Settings J2: DOC® 2000 address setting Pins Address 1-2 3-4 5-6 closed closed closed C800 closed closed open CC00 *closed open closed D000 closed open open D400 open closed closed D800 open closed open DC00 open open closed E000 open open open OFF J3: LCD power Closed pins Voltage 1-2 3.3 V *2-3 5 V J4: Clear CMOS Closed pins Result 1-2 Clear CMOS *2-3 3.6 V battery J5: Audio AMP power Closed pins Audio power 1-2 From main power (5 V) *2-3 From 7805CT (5 V) J7: COM2 selector Closed pins Result *1-2 RS-232 3-4 RS-422 5-6 RS-485 *default setting PCM-4825/4825L Startup Manual 3 Locating Connectors J4 J3 J5 J7 J2 CN1 CN2 CN4 CN7 CN6 CN12 LED J6 CN15 CN8 CN14 CN11 CN10 CN9 CN13 CN3 CN5 SIMM1 Locating Jumpers Mechanical Drawing Mechanical Drawing Mechanical Drawing Mechanical Drawing Mechanical Drawing