Air King AIG4 Manuals

READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. GENERAL SAFETY INFORMATION When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to person, including the following: WARNING: DO NOT CONNECT POWER SUPPLY UNTIL FAN IS COMPLETELY INSTALLED. MAKE SURE ELECTRICAL SERVICE TO THE FAN IS LOCKED IN OFF POSITION. 1. Read all instructions before installing or using exhaust fan. 2. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. 3. Before servicing or cleaning the unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 4. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-related construction. 5. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration, and Air Conditioning Engineers (ASHRAE), and the local code authorities. CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS. Models: AIK14X, AIK16X, AIK24Y, AIK26Y, AIF4X, AIF6Y, AIF8X, AIF10X, AIG4, AIG6 www.airkinglimited.com 5S7635036 New 9-06 In-Line Exhaust Fan SAVE THESE INSTRUCTIONS 6. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. 7. Ducted fans must always be vented to the outdoors. 8. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 9. Acceptable for use over a bathtub or shower when installed in a GFCI protected branch circuit. 10. Suitable for use with solid-state speed control. 11. This unit has rotating parts and safety precautions should be exercised during installation, operation and maintenance. 12. Guards must be installed when fan is within reach of personnel or within seven (7) feet of working level or when deemed advisable for safety. 13. NEVER place a switch where it can be reached from a tub or shower. 14. Do not insert or allow fingers or foreign objects to enter the motor. WARNING: DO NOT USE IN KITCHENS IMPORTANT INSTRUCTIONS - OPERATING MANUAL 1 of 12

SPECIFICATIONS HOUSINGS INLINE INLETS INLINE EXHAUST FAN INLET GRILLS / HOUSINGS • Inlet Grill Low profile, circular plastic exhaust grill • Housing Models AIG4: Galvanized metal collar with mounting straps and AIG6 metal back draft damper with rubber gasket to reduce sound level during opening and closing. Models AIG46HL: Metal housing with wiring junction box and AIG46F metal back draft damper with rubber gasket to reduce sound level during opening and closing. • Lighting Model AIG46HL: 50 watt, Halogen Lamp, UL approved for wet locations included with unit. Model AIG46F: ENERGY STAR 14 watt, Wet Location Compact Fluorescent 4 Pin Lamp included with unit. • Unit Mounting Models AIG4: Metal mounting straps for quick and easy AIG6 installation to joist. Models AIG46HL: Metal housing with wiring junction box for AIG46F quick and easy installation between joist. • UPC Codes AIG4: 0-83162-31131-3 AIG6: 0-83162-31132-0 AIG46HL: 0-83162-31122-1 AIG46F: 0-83162-31141-2 Canada: 110 Glidden Road Brampton, Ontario L6T 2J3 Tel: (905) 456-2033 Fax: (905) 456-1015 U.S.: 820 Lincoln Drive West Chester, Pennsylvania 19380-4466 Tel: (877)-304-3785 Fax: (610) 696-8048 Rev. A 12-06 Specifications subject to change without notice. C US PROJECT LOCATION CONTRACTOR ARCHITECT ENGINEER SUBMITTED BY DATE FAN MODEL CFM IN RPM WATTS AMPS SONES QTY OPTIONAL EQUIPMENT NUMBER NUMBER W.G. & REMARKS Models A B C D E F G H AIG4, AIK14X, AIK24Y 4" 35/8" 47/8" 33/4" 17/8" 3/8" - - AIG6, AIK16X, AIK26Y 6" 55/8" 7" 33/4" 17/8" 3/8" - - AIG46L, AIG46YL, AIK14XL 6" 55/8" 7 3/32" 6" 13/4" 3/8" 723/32" 4" AIK14XF, AIK26YL, AIK26YF F C D A B E F C B A G D E H

INSTALLING AIG4, AND AIG6 SUPPLY GRILL WITH MOUNTING COLLAR WITH BACKDRAFT DAMPER Step 1 - Select the grill mounting point within the area to be ventilated. To ease installa- tion, locations of framing beams within the walls or joists supporting the ceiling should be considered. Collar is provided with a perforated hanging strap for attachment directly to a beam or joist. if the location of the grill does not allow direct attachment, a cross- member mounted to the framing should be used. Step 2 - Place the mounting collar in the selected location and trace a circle onto the sur- face. From the interior side of the room, cut through the surface. Please note: In order to assure a smoother finish when mounting through a sheetrock or tile type ceiling, it is rec- ommended that a razor knife be used to make the cut. Step 3 - From within the attic or crawl space, place the mounting collar into the hole until the edge of the collar is flush with the interior wall or ceiling surface. Attach collar to the support beam with the 1" wood screws provided. Attach duct work. Please note: If beam or joist exceeds the height of the collar, allow sufficient space between the collar and the beam to attach the duct work. Also, when attaching flex duct to the collar/damper combi- nation and an immediate elbow is necessary, be certain that the elbow is installed with a "soft" bend to allow damper to operate preperly. Step 4 - Snap the grill into the mounting collar. Grill should be pushed tightly into place for an airtight fit. FOR PARTS OR TECHNICAL ASSISTANCE - Please call: 1-800-465-7300 MONDAY THROUGH FRIDAY, BETWEEN THE HOURS OF 8 AM AND 4:00 PM EST. DO NOT RETURN PRODUCT TO PLACE OF PURCHASE. FOR more information please visit our website: www.airkinglimited.com INSTALLER LA GRILLE AIG4, ET AIG6 AVEC LE COLLIER DE FIXATION AVEC LE RÉGULATEUR DE DÉCHARGE Étape 1 - Sélectionner le lieu d'installation de la grille au sein de l'espace être ventilé. Pour faciliter l'installation, on devrait tenir compte de l'emplacement des colombages dans les murs ou encore des solives supportant le plafond. Le collet est accompagné d'une courroie performée pour l'instal- lation directement aux colombages ou aux solives. Si l'emplacement de la grille ne permet pas une fixation directe, on doit utiliser une traverse attachée à la structure. Étape 2 - Placer le collet de montage au lieu choisi et tracer un cercle sur la surface. De l'intérieur de la pièce, découper la surface. Veuillez noter qu'afin d'assurer un fini plus unis lors de l'installa- tion dans un plafond en gypse ou en tuiles il est recommandé d'utiliser un couteau à lame à gypse. Étape 3 - De l'intérieur de l'entre-toit ou de l'espace restreint, placer le collet de montage dans l'ou- verture jusqu'ce que le rebord du collet soit égal avec le mur intérieur ou la surface du plafond. Fixez le collet une poutre avec les vis à bois de 1 po qui sont fournis. Attacher les conduits. Veuillez noter: Si la poutre ou la solive dépasse la hauteur du collet, laissez suffisamment d'espace entre le collet et la poutre afin d'y fixer le conduit. De plus, lorsqu'on attache un conduit flexible à la combi- naison collet/registre et qu'un coude immédiat est requis, assurez-vous que l'angle soit installé de façon à permettrie aux lamelles du registre de bien fonctionner. Étape 4 - Enclenchez la grille dans le collier de fixation. La grille devrait être poussé étroitement dans l'endroit pour un ajustement hermétique. INSTALACION DE REJILLAS DE ENTRADA AIG4, Y AIG6 CON COLLARIN DE MONTAJE, CON MARIPOSA DE CONTRATIRO. PASO 1 - Seleccione et sitio de montaje de la rejilla dentro del ambiente a ventilar. Para facilitar hay que tener en cuenta la ubicación de las vigas estructurales de las parededs y del cielo raso. El col- larín viene con un tirante perforado para fijación directa a una viga o vigueta. Si la ubicación de la parrilla no permite une fijación directa, habrá que usar travesaños adosados a las vigas. PASO 2 - Coloque el collarín adaptador en el sitio slecccionda y trace un círculo en la superficie. Deste el interior del cuarto, haga un corte a través de la superficie. Nota: Para logar un acabado más uniforme al atravesar un cielo raso compuesto de cartón de yeso o de losaas acústicas, enre- comendable usar una navaja para harcer el corte. PASO 3 - Desde la buhardilla o especio de "gateo" encima del cielo raso, inserte el collarín de mon- taje en el agujero hasta que quede el borde del collarín al ras de la pared interior o superficie del cielo raso. Conecte el conducto. Favor tomar nota: Si la viga o vigueta excede la altura del collarín, deje un espacio adecuado entre el collarín y la viga para conectar el conducto. Asimismo, al conec- tar un conducto frlexible al conjunto de collarín y regulador (mariposa), si hay que instalar un codo contiguo, tenga cuidado de montar el codo con una curva "suave" a fin de que las hojas del regu- lador funcionen lebremente. PASO 4 - Enganche la rejilla a presión en el collarín de montaje. La rejilla se debe aprisionar firme- mente para que quede hermética. .

IMPORTANT INSTRUCTIONS - OPERATING MANUAL READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. GENERAL SAFETY INFORMATION When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to person, including the following: SAVE THESE INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSON, OBSERVE THE FOLLOWING: a) Use this unit only in the manner intended by the manufacturer.If you have questions, contact the manufacturer. b) Before servicing or cleaning the unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSON, OBSERVE THE FOLLOWING: a) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-related construction. b) Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration, and Air Conditioning Engineers (ASHRAE), and the local code authorities. c) When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. d) Ducted fans must always be vented to the outdoors. e) If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit. f) This unit must be grounded. g) To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. h) Suitable for use with electronic speed control device. i) Do not install into ceilings thermally insulated to a value greater than R40. CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS. WARNING: DO NOT USE IN KITCHENS. k) Read all instructions before installing or using exhaust fan. www.airkinglimited.com A210952017 Rev. B 8-12 1 of 12 In-Line Exhaust Fan Models: AIK14X, AIK16X, AIK24Y, AIK26Y, AIF4X, AIF6Y, AIF8X, AIF10X, AIG4, AIG6