AJAX WallSwitch Manuals

1. PURPOSE WallSwitch remote controller is used to switch on and off appliances maximum power of less than 3 kW. Wallswitch housing is designed for installation in a standard european wall mounted junction box. The switch operates as a part of Ajax system. 4. GETTING STARTED 4.1 Before switch installing the power must be switched off! Remove the safety device or switch off automaton which supplies socket with electricity, to which WallSwitch will be installed! 4.2 Connect WallSwitch as in diagram (PICTURE 1). SPECIFICATION MEANING Use Indoor Actuator Relay Relay service life 200 000 switchings Power supply voltage 110-240 V AC±10% 50/60 Hz Voltage protection for 230 V electrical network Max 264 V, min 161 V Voltage protection for 110 V electrical network Max 126 V, min 77 V Load maximum current 13 А Maximum current protection Yes (13 А) Allowed power (resistive load at 230 V): Up to 3 kW Allowed power (resistive load at 110 V): Up to 1.5 kW Electric meter option Yes (statistics available) Monitoring of power consumption param- eters Yes (current, voltage, power consump- tion) Allowed operating ambient temperature From 0°С (+32°F) to +64°С (+147.2°F) Maximum temperature protection Yes (65°С (+149°F) inside the wall box) Communication protocol Jeweller (868 or 915 MHz depending on the country of distribution) Radio signal power 25 mW Command response time Less than a second Maximum distance between detector and Hub Up to 1000 m (3300 ft) (in open area) Power consumption in standby mode Less than 1 W Ingress protection IP20 Operating humidity Less than 75% Dimensions 38х25х18 mm (1.49x0.98x0.70 in) Dimenstions for mounting in the wall plate Ø ≥ 50 mm (1.97 in), depth 55 mm (2.17 in) Weight 32 g 3. PACKAGE CONTENTS 2. SPECIFICATIONS WallSwitch IMPORTANT! The switch works only with the Ajax Hub. IMPORTANT! In case of inductive or capacitive load use the output permissible power is lowered to 2 kW! IMPORTANT! Comply with safety standards when operating electrical appliances! All switch installation works should be performed only by a qualified electrician. To avoid the risk of electric shock during installation, disconnect the electrical network leading to the plug-switch prior to installation, make sure that there is no voltage on the wires, having checked it with a multitester or a multimeter. It is strictly prohibited to disassemble switch under voltage, even if the relay is switched off! During installing comply with the state requirements and regulations. IMPORTANT! When mounting WallSwitch into wall mounted junction box place it’s antenna as far as possible from the metal objects (wires, fasteners, etc.). It is recommended to install antenna under the external plastic decorative panel. Do not shorten or cut the antenna in any case. Do not use WallSwitch with a damaged body and/or antenna, it may cause a short circuit or an electric shock! AJAX L N PICTURE 1. Wiring diagram of WallSwitch switch PICTURE 2. Recommended WallSwitch antenna placement (under the front panel) WallSwitch switch, 2 connecting wires, manual. IMPORTANT! Do not connect to WallSwitch load more than 3 kW. When connecting the load, please carefully learn the wiring diagram (PICTURE 1), as incorrect wiring can cause damage to the device and / or destruction of property.

Guide rapida | Ita Ajax WallSwitch Relè Wireless con misuratore di consumo Guía rápida | Es Ajax WallSwitch Relé de control remoto y medidor de consumo Quick Start Guide | En Power relay Model Name: Ajax WallSwitch Wireless power relay with energy monitor WallSwitch è un dispositivo che unisce un relè di accensione wireless per dispositivi elettrici con capacità fino a 3kW ed un misuratore di consumo d’energia. È adatto ad installazioni in scatole di incasso. WallSwitch è connessa al sistema di sicurezza Ajax tramite il protocollo Jeweller, con un raggio di comunicazione fino a 1000 metri senza ostacoli. IMPORTANTE: Questa guida rapida contiene informazioni generali sul WallSwitch. Prima di usare il dispositivo si raccomanda di consultare il Manuale al sito web: ajax.systems/support/devices/wallswitch 1. Antenna. 2. Morsetti. 3. Indicatore luminoso. 4. Pulsante funzione. Connessione e configurazione La connessione e la configurazione del dispositivo avviene tramite l’applicazione Ajax Security System. Per iniziare ad utilizzare WallSwitch, si deve collegare all’alimentazione ed aspettare 10-15 secondi. Successivamente, è possibile iniziare la procedura di aggiunta dei dispositivi con l’applicazione per smartphone. Premere e tenere premuto il tasto funzione del WallSwitch per alcuni secondi (o dare una carica al dispositivo di almeno 20W, per esempio collegandoci un tostapane). Per collegare l’Hub al dispositivo, posizionarli ad una distanza ravvicinata. Configurazione dei parametri di protezione: Protezione corrente: se attiva, l’alimentazione verrà interrotta se l’intensità della corrente supera i 13A, se inattiva la soglia è 19,8A (o 16A, se continua per 5 secondi). WallSwitch es un dispositivo que combina un relé de encendido y apagado inalámbrico para aparatos eléctricos con capacidad de hasta 3 kW y un medidor de consumo de energía. Está adaptado para su instalación en una caja de mecanismos europea. WallSwitch se conecta al sistema de seguridad Ajax a través del protocolo Jeweller, cuya comunicación tiene un rango de alcance de hasta 1.000 metros sin obstáculos. IMPORTANTE: Esta guía rápida del usuario contiene información general sobre WallSwitch. Antes de utilizar este dispositivo, le recomendamos encarecidamente que consulte la guía completa del dispositivo en el sitio web de Ajax: ajax.systems/support/devices/wallswitch 1. Antena 2. Conectores 3. Indicador luminoso 4. Botón de control Conexión y configuración del dispositivo La conexión y configuración del dispositivo se realiza a través de la aplicación móvil Ajax Security System. Para comenzar a utilizar WallSwitch, debe conectarse a una fuente de alimentación y esperar 10-15 segundos. A continuación, iniciar el procedimiento para añadir dispositivos en la aplicación móvil, presionar y mantener presionado el botón de control de WallSwitch durante varios segundos (o aplicar una carga al dispositivo de al menos 20 W. Por ejemplo, activando una tostadora). Para que se produzca la conexión entre el dispositivo y el Hub, deben situarse uno del otro a una distancia cercana. Parámetros de protección en la configuración: Protección contra corriente: si esta opción está habilitada, la fuente de alimentación se WallSwitch is a device combining a wireless power on and off relay for electrical appliances with the capacity up to 3 kW, as well as a power consumption detector. It is adapted for installation in a European socket box. WallSwitch is connected to the Ajax security system via the protected Jeweller protocol, with an effective communication range of up to 1,000 meters without obstacles. IMPORTANT: This Quick Start Guide contains general information about the WallSwitch. Before using the device, we recommend to reviewing the User Manual on the website: ajax.systems/support/devices/wallswitch 1. Antenna. 2. Terminal blocks. 3. Light indicator. 4. Functional button. Connection and Setting Up The relay is connected and set up via the Ajax Security System mobile application. For WallSwitch to become available for detection, you should connect it to power supply and wait for 10-15 seconds. Then launch the device adding procedure in the mobile application and press the WallSwitch functional button (or apply load to the device no less than 20 W, e.g. by switching on an iron or electric kettle). For the pairing to occur, the relay and the hub should be located within the same premises . You can change the protection parameters in the settings: Current protection - if enabled, power supply will be switched off if the strength of current exceeds 13A, in the inactive state the threshold

WallSwitch User manual Updated January 27, 2021 WallSwitch is a wireless indoor power relay featuring a power consumption meter. The miniature body of the device is adapted for installation in a European-type socket. Regardless of the type of electrical circuit, only a qualified electrician should install WallSwitch! WallSwitch operates only within the Ajax security system (integration into third- party security systems is not provided), communicating with a via the protected protocol. The communication range is up to 1,000 meters in the line of sight. Use scenarios to program actions of (Relay, WallSwitch, or Socket) in response to an alarm, press, or schedule. A scenario can be hub Jeweller automation devices Button

WallSwitch User manual Updated September 30, 2019 WallSwitch is a device that combines a wireless power on/off relay for electrical appliances and a power consumption meter. The miniature body of the device is adapted for installation in a European type socket. WallSwitch should be only installed by a qualified electrician! Regardless of the type of the electrical circuit in which the device is installed. WallSwitch operates only with the Ajax security system (it may not be used in any third-party security systems), by connecting via the protected Jeweller protocol to the hub. Communication range – up to 1,000 meters, absent any obstacles. Operates only with Ajax hubs. Connection to ocBridge and uartBridge integration modules is not provided. The Ajax security system is self-sustaining, but the user can connect it to the central monitoring station of a private security company. Buy power relay WallSwitch