Alarm Lock RR-4BKEYFOB Manuals

1 OVERVIEW The 4-button Wireless Remote Release (order part RR- 4BKEYFOB) is used to wirelessly unlock up to four separate Trilogy Networx™ series locking devices, OR locking devices wired to the RR-RECEIVER (see WI2012). The Wireless Re- mote is intended as a portable pocket-size remote release (for a 1-button model intended for fixed mounting at a hidden loca- tion, see model "RR-1BUTTON"). The Wireless Remote re- quires one battery (pre-installed) that features a service life of up to 12,000 openings (use a 3V Lithium type CR2032 or Dura- cell DL2032 only). During normal operation, the locking device typically opens within 2 seconds of the button press. Each of the four buttons can be "paired" (connected) with one Networx locking device (four buttons can be paired with four separate locking devices). In addition, each individual Networx locking device contains ten (10) "slots", with each slot available to accommodate one keyfob button. Therefore, each individual Networx locking device can ultimately be paired with up to ten Wireless Remote buttons on multiple keyfobs. Note: Each but- ton can ONLY be paired with one specific Networx locking de- vice at a time (thus when a previously paired button is later paired with a second locking device, the first pairing is erased). The Wireless Remote is not currently supported by PL Series Networx locking devices. Visit the Alarm Lock website (www. alarmlock.com) for supported firmware versions. PAIRING PROCEDURE Pairing is performed locally at the keypad. Important: This pairing procedure should be performed after the locking device has been programmed by DL-Windows. 1. Open DL-Windows, select the desired Lock Profile, open the Programmable Features screen, Remote tab. Check to enable one of the following desired features: • Remote Release (Momentary) --or-- • Remote Toggles Passage Mode If neither are checked, the Wireless Remote pairing will be disabled upon subsequent DL-Windows programming downloads. Therefore, check to enable one of these two features and then send the programming to the locking de- vice (see OI352 for complete DL-Windows programming instructions). This will ensure that the pairings to be added now will be unaffected by later downloads. 2. At the locking device keypad, enter Program Mode (press the Master Code followed by ;). 3. To pair the first remote, press: ; 6 5 ; 1 : Verify keypad sounds "beep-beep-beep" continuously. (The "beep-beep-beep" indicates the locking device is ready and will wait about 30 seconds for the next step). 4. With the Wireless Remote in hand, observe its LED as you perform the next steps: a. Press and hold one of the four buttons. b. The red LED lights...keep holding the button… c. When the LED flashes green, release the button... d. Wait a few seconds...observe the LED as follows: • LED solid green = Pairing successful. Go to step 5 to pair another Wireless Remote; otherwise go to step 6. • LED solid red = Pairing unsuccessful. Start again at step 3. 5. To pair another Wireless Remote, you will need to start again at step 3, but with a slight change, as follows: As previously stated, up to ten (10) Wireless Remote but- tons may be enrolled into one locking device. Each Wire- less Remote button added occupies a "slot" (numbered 1- 10); therefore, increment the "slot" number of the new Wire- less Remote button in step 3. For example, when pairing the first remote in step 3, you pressed: ; 6 5 ; 1 : To pair a second remote, you will need to press: ; 6 5 ; 2 : To pair a third remote, you will need to press: ; 6 5 ; 3 : ...and so on. Therefore, to enroll another Wireless Remote, go to step 3, but use the incremented Wireless Remote "slot" number. Use the table below to track the location of each Wireless Remote button in your system: Use this table to track the fob button and its device pair: © ALARM LOCK 2012 WI2004 7/12 345 Bayview Avenue Amityville, New York 11701 For Sales and Repairs 1-800-ALA-LOCK For Technical Service 1-800-645-9440 (Note: Technical Service is for security professionals only) Publicly traded on NASDAQ Symbol: NSSC Slot 1: Slot 6: Slot 2: Slot 7: Slot 3: Slot 8: Slot 4: Slot 9: Slot 5: Slot 10: Location of Locking Device: Keyfob Location of Locking Device: Button 1 Button 2 Button 3 Button 4 RR-4BKEYFOB Wireless Remote Release Keyfob Programming Instructions When Used with Trilogy Networx™ Locking Devices