AMERITRON AL-811HX Manuals
1 pdf manual(s) AMERITRON AL-811HX for free download (Document Types: Unpacking instructions manual)
AMERITRON AL-811HX Unpacking instructions manual [PDF] (11 pages)
- Identifier: id-2204048
- Brand: AMERITRON
- Device: AL-811HX Amplifier
- Type: PDF
- Key Aspects: Unpacking and Inspection Guidelines, Technical Data and Parameters, Component Overview and Descriptions
- UPD Date: 09.06.2026
- Source File: 2083584.pdf
- Pages: 11
- Description: User support guide for the AMERITRON AL-811HX.
Click to expand and read text
PLEASE READ THIS MANUAL BEFORE ATTEMPTING TO OPERATE EQUIPMENT!! UNPACKING INSTRUCTIONS 1. Carefully lift the amplifier by the bottom cabinet edge out of the shipping carton. Place the amplifier on a firm, level surface and carefully inspect it for shipping damage. Contact the shipper immediately if any damage exists. Save the carton and packing material for possible shipping in the future. 2. Remove the twelve screws holding the cover on with a number 2 phillips screwdriver. Carefully lift the cover off the amplifier. Save the screws to rescuer the cover. Note that the AL811H is shipped with the fuses and fuse caps inside the amplifier. 3. Locate the fuse pack with the two 12 ampere fuses and fuse caps. If additional screws are needed, they will be in the fuse pack also. NOTE: Fuses supplied are for 120/110/100V operation (Models AL-811H/HY). If you are rewiring the AL-811H for 240/230/220V operation, you must use 8 ampere fuses. The AL-811HX export model is pre-wired for 240V operation and is supplied with 8 ampere fuses. 4. Remove the foam packing material (around the tubes) that secures the 811A tubes during transit. Carefully unwrap the tubes. Do not dislodge or break the shaft that is connected to the rear input bandswitch wafer. 5. To install the tubes in the sockets, be sure the large diameter pins line up with the two large diameter holes in each socket. Do NOT rock or twist the tubes excessively during the installation. If the tubes are already installed, check them for proper seating. If necessary, press the tubes down into their sockets with gentle force. Do not rock or twist the tubes excessively. Also, check that the anode caps are secure and that they did not come loose during the unwrapping process. 6. The white ceramic anode connector will have to be removed from the top metal cap of each tube if it ever becomes necessary to remove the tubes from the amplifier. This can be a difficult procedure because the high clamping force of the internal springs in the anode connector may hold it to the cap very tightly. The tube will break if direct upward or rocking pressure is applied in an attempt to remove the connector. The safest way to remove the ceramic connector is to lift the tube out of its socket. A twisting or spinning pulling motion can then be applied while holding the ceramic connector firmly until the tube and connector are separated. Repeat the procedure with each tube. 7. Install the cover with the vent holes to the left (near the tubes) by installing the back screws first. Install all the screws loosely and tighten them only after all the screws are in place. 8. Install the fuses and fuse caps on the back of the unit. Read the manual to become familiar with the operation of the AL-811H amplifier.
AL-811HX: Related Instructions
AMERITRON AL-8OA HIG FI POWER LINEAR AMPLIFIER i INSTRUCTION MANUA The Amentron AL-BOA Linear Amplif ier is designed for over 1000 Watts output SSB PEP (850 Wat Official operating instructions for the AMERITRON AL-80A Amplifier. The document elaborates on device functions and device features, device instructions, operating modes, troubleshooting.
MFJ-216 Instruction Manual Deluxe Amplifier Saver 1 MFJ-216 Deluxe Amplifier Saver The MFJ-216 Deluxe Amplifier Saver re Official installation manual for the AMERITRON MFJ-216 Amplifier. It outlines maintenance guidelines and technical overview, wiring setup, maintenance procedures.
User reference guide for the AMERITRON RCS-10 Switch. It describes step-by-step installation, device instructions, usage examples, usage tips.
ADL-2500 Dry Dummy Load Instruction Manual 1 ADL-2500 2500 Watts Dry Dummy Load AMERITRON's Dry Fan Cooled Dummy Load simulates an accurate 50 Ohm antenna up t User support manual for the AMERITRON ADL-2500 Test Equipment. The manual includes instructions for energy usage, network setup, operating guidelines.
While tuning 8l I tube type amplifiers always limit the transmitting time to no more than 5 seconds with a l0 second cool down. It is best to use CW, FM, RTTY M Device user manual for the AMERITRON AL-811HXCE Amplifier. This manual elaborates on firmware installation, installation guides, warranty information.
Table of Contents Amplifier Features ...........................................................................................................3 Power Supply F Official operating instructions for the AMERITRON ALS-600PS Amplifier. This documentation highlights features and safety information, hardware instructions, setup instructions.
Similar Manuals in the Amplifier Category
Print Date: 12/17/96 Copyright © 1996 Glenayre 250-Watt Gold Line Power Amplifier Issue 1, Rev. C: 10/21/96 Specifications subject to change without notice Cop Device setup guide for the Glenayre GL-T8500 Amplifier. The document explains maintenance, maintenance schedule, safety protocols, wiring setup.
SERVICE MANUAL DIGITAL THEATER AMPLIFIER 12 / 04-A 68E37809S01 MRA-D550 Product usage guide for the Alpine MRA-D550 - V12 Amplifier Amplifier. It provides guidance on daily usage, interface navigation, testing procedures.
AUDIO AMPL PROFESSION PROFESSIONAL AUDIO AMPLIFIER AV2.2P AV2.4P OPERATION MANUAL UDIO AMPL A AV2.2P AV2.4P Product documentation for the AUSTRALIAN MONITOR AV2.2P Amplifier. This reference manual explains security instructions, safety precautions, safety protocols.
SA-3 Subwoofer Amplifier Now Hear This 6400 Goodyear Road Benicia, CA 94510 800-NHT-9993 OWNER’S MANUAL Instruction guide for the NHT SA-3 Amplifier. This guide offers guidance on product handling, maintenance schedule, user instructions, calibration steps.