AMX AVB-TX-DGX-HD15-SC Fiber Manuals

Instruction Manual AMX AutoPatch DGX Fiber Modules DGX Transmitters & Receivers AVB-TX-DGX-HD15-SC Fiber AVB-TX-DGX-DVI-SC Fiber AVB-RX-DGX-SC Fiber-HD15 AVB-RX-DGX-SC Fiber-DVI REV D: 3/15/2013

Quick Start Guide AutoPatch DGX Fiber TX and RX Modules Overview and Specifications DGX Fiber Transmitters (TX) and Receivers (RX) are modules that work together or in conjunction with DGX SC Fiber boards on an AMX AutoPatch DGX Distribution Matrix. The transmitters feature Auto-Detect, and the receivers feature SmartScale™. This Quick Start Guide contains basic installation information and specifications for the four modules listed below. For complete information and specifications, see the DGX Transmitters & Receivers Instruction Manual on the AMX AutoPatch CD or at www.amx.com. For use with a DGX Distribution Matrix, see the product’s Quick Start Guide and/or Instruction Manual. Compatibility Note: DGX Fiber Transmitters and Receivers are not compatible with third party optical distribution amplifiers or multimode to single-mode converters. * A desktop power supply (ENERGY STAR® qualified) is provided with each module. ** 3,000 foot cable requires 50/125 μm OM2 class low loss fiber cable. Transmission distance will vary (more or less) depending on the type/quality of fiber used, fiber bandwidth, cable bend radius/kinks, splicing quality and quantity, and chromatic or modal dispersion. * 96 kHz audio only available for source video 800x600@ 60Hz (40 MHz pixel clock) or greater. Otherwise, 48 kHz is the maximum. EDID TX Standard Timing Identification EDID TX Established Timing Module Installation System Setup DGX TX Modules The DGX DVI TX receives a DVI signal and the DGX HD-15 TX receives an analog video signal.** Both TXs receive either a digital audio or an analog stereo audio signal from the source device (digital takes precedence if both are connected). Video and embedded audio and data signals are sent over an SC fiber cable to an RX module. The RS-232 ports can supply unidirectional RS-232 serial data with the data flow in the same direction as the video. Each TX also has a local video output connector. ** Supports RGBHV, RGBS, RGsB, or Y/Pb/Pr (Y/Pb/Pr up to 1080p) video formats. DGX RX Modules Each DGX RX accepts its video, audio, and data signals from a DGX TX via the fiber cable, converts the video to either DVI or RGBHV (depending on the model), and sends the signal to the destination. Audio on each RX will be output on both the digital and analog stereo ports. FIG. 1 DGX Fiber Transmitters and Receivers General Specifications and Product Information Approvals UL, cUL, CE, FCC Class A, RoHS AC Power 100 to 240 VAC single phase, 50 Hz to 60 Hz 0.6 A @ 115 VAC max. Power Consumption (max.) +12 V, 1.25 A (15 W) Thermal Dissipation (max.) 51 BTU/hr. Power Connector* 2.1 mm DC power jack Operational Temperature Storage Temperature 32° F to 113° F (0° C to 45° C) -22° F to 158° F (-30° C to 70° C) Humidity 0 to 90% non-condensing Dimensions 5.15 in. (13.08 cm) depth; 5.80 in. (14.73 cm) width; 1.66 in. (4.22 cm) height Weight / Shipping Weight Approximately 1.75 lb. (0.8 kg) / 2.75 lb. (1.25 kg) MTBF 92,000 hrs. Safety Certifications (DGX DVI TX and DGX HD-15 TX) Class 1 Laser Product (Class 3R Laser Product when fiber is disconnected from unit) IEC 60825-1, 2001 Compatible AMX AutoPatch Fiber Products Other AMX AutoPatch DGX Signal Management products Advanced Configuration Interface USB Mini-B Fiber Cable Type (SC Termination) Multimode Simplex, 50/125 μm preferred or 62.5/125 μm Fiber Cable Length Up to 3000 ft. (914.4 m) with 50 μm cable** Up to 1500 ft. (457.2 m) with 62.5 μm cable Optical Budget 9.75 dBm (typical) between DGX TX and RX Optical Modulation Amplitude (OMA): -6.25 dBm (typical) OMA Sensitivity: -16.0 dBm (typical) Power Output of Laser Radiation (max.) 4.08 mW (DVI TX and HD-15 TX only) Fiber Cable Connector SC Optical Analog Video and DVI Video Resolution Support 640x480 @ 60 Hz up to 1920x1200 @ 60 Hz Data Rate (max.) 4.95 Gbps Pixel Clock 25 MHz to 165 MHz Video Digital Processing 24 bit, 165 MHz Input Interlaced Video Support 1080i 60, 59.94, 50 fields/sec.; 576i 100 fields/sec. Analog video only 576i 50 fields/sec. and 480i 60 fields/sec. Interlace video supported into the TX Progressive only supported out of the RX DDC/EDID Support EDID provided by DGX TX (EDID is user re-programmable) Analog Video Only TX Input Signal Types RGBHV, RGBS, RGsB, Y/Pb/Pr TX Auto-Adjust Input Yes TX Input and Local Output Connectors HD-15 (RGBHV and Y/Pb/Pr) RX Output Signal Type RGBHV RX Output Scaling SmartScale™, Presets, Manual Configuration RX Output Connector HD-15 (RGBHV) Front View Rear View AVB-TX-DGX-HD15-SC Fiber FG1010-200-01 AVB-RX-DGX-SC Fiber-DVI FG1010-410-01 AVB-RX-DGX-SC Fiber-RGBHV FG1010-400-01 AVB-TX-DGX-DVI-SC Fiber FG1010-210-01 DVI Video Only TX Input and RX Output Signal Types DVI-D (single link) TX HDCP Support No TX Input and Local Output Connectors DVI-I (DVI-D single link is supported signal type) RX Output Scaling SmartScale™, Presets, Manual Configuration RX Output Connector DVI-I (DVI-D single link is supported signal type) Input Cable Length Meets DVI spec of 5 m (16.4 ft.) Audio – Analog and Digital TX Input and RX Output Signal Types Stereo analog, S/PDIF (2 Channel L-PCM) Video signal must be present to pass audio TX Analog Input and RX Output Level (max.) +8 dBu, unbalanced TX and RX S/PDIF Resolution 16 bit to 24 bit TX and RX S/PDIF Sample Rate 32 kHz, 44.1 kHz, 48 kHz, 96 kHz* TX Analog to Digital Reference Level RX Digital to Analog Reference Level +8 dBu = 0 dBfs 0 dBfs = +8 dBu Audio Synchronization Progressive and interlace video formats @ 60 Hz frame rate. Audio is actively delayed to match video within 8 ms leading or lagging. Connectors RCA (S/PDIF) and 3.5 mm mini-stereo (analog) jacks Serial Data TX Input and RX Output Signal Type (video must be present to pass data) Unidirectional RS-232, control signal transmitted in the same direction as the video/audio TX Input and RX Output Signal Level (max.) +/-15 V TX and RX Baud Rate (max.) 115.2 k baud, 25 ft. (7.6 m) copper cable TX and RX Baud Rate (typical) 57.6 k baud, 150 ft. (45.7 m) copper cable TX Input and RX Output Connectors Pluggable 3.5 mm terminal block FIG. 2 Typical system setup (use either model DGX TX with either model DGX RX) ID 1: 1920x1200 @ 60 Hz (preferred timing identified in EDID) ID 2: 1920x1080 @ 60 Hz ID 3: 1680x1050 @ 60 Hz ID 4: 1600x1200 @ 60 Hz ID 5: 1280x800 @ 60 Hz ID 6: 1280x720 @ 60 Hz ID 7: 1280x1024 @ 60 Hz ID 8: 640x480 @ 120 Hz 832x624 @ 75 Hz 1280x1024 @ 75 Hz 1152x870 @ 75 Hz – 640x480 @ 60 Hz, 67 Hz, 72 Hz, 75 Hz 800x600 @ 56 Hz, 60 Hz, 72 Hz, 75 Hz 1024x768 @ 60 Hz, 70 Hz, 75 Hz, 87 Hz 720x400 @ 70 Hz, 88 Hz SC fiber up to 3000 ft. (914 m) Source Device Destination Device USB TX RX Control PC Local Video Output For setup only for systems with special requirements (see manual) USB