AMX Mio Moderno MIO-IRRX Manuals

Quick Start Guide Mio Modero® IR Receiver Overview The Mio Modero IR (FG5797-01xx; xx indicates color selection) is a remote IR receiver for use with NetLinx Central Controllers and operates via the AXlink bus to remotely control devices. The Mio Modero IR is in a wall panel that fits into the US- style single-gang enclosure and most International single-gang enclosures. The Mio Modero IR works with AMX 38 kHz and 455 kHz IR transmitters. Available Color Schemes The Mio Modero device family is available in a range of colors. The IR supports these color schemes, Black (BL), White (WH), and Beige (BG). Wiring and Installation Note: Before touching the device, discharge the static electricity from your body by touching a grounded metal object. Set the receive AXlink device number before installing the Mio Modero IR. FIG. 2 illustrates the location of key components on the Mio Modero IR circuit board. Setting the AXlink Device Number 1. If connected, disconnect the power supply. 2. Locate the 8-position Device DIP switch (FIG. 2). 3. Set the DIP switch according to the DIP switch values shown below. The device number is set by the total value of DIP switch positions that are ON (up). As an example, the DIP switch in FIG. 3 defines device number 129 (1+128=129). If you later change the device number, remove and reconnect the AXlink power connector to enter the new device number into memory. Preparing captive wires You will need a wire stripper, and flat-blade screwdriver to prepare and connect the captive wires. 1. Strip 0.25 inch (6.35 mm) of wire insulation off all wires. 2. Insert each wire into the appropriate opening on the connector according to the wiring diagrams and connector types described in this section. 3. Turn the flat-head screws clockwise to secure the wires in the connector. Note: Do not over-torque the screws; doing so can bend the seating pins and damage the connector. Wiring Guidelines The Mio Modero IR requires 12 VDC power to operate properly. The power is supplied by the AMX system's AXlink cable. The maximum wiring distance between the Central Controller and the receiver is determined by power consumption, supplied voltage, and the wire gauge used for the cable. The following table lists wire sizes and the maximum lengths allowable between the receiver and the Central Controller. The maximum wiring lengths are based on a minimum of 13.5 volts available at the Central Controller's power supply. If the distance is greater than what is listed in the table, consult the Mio Modero Device Family Instruction Manual for wiring with external power sources. FIG. 1 Mio Modero IR receiver Mio Modero IR Specifications Power: 12 vDC, 15 mA Receive Frequencies: 38 and 455 kHz Range 38KHz: • transmitter at 38Hz and at 50° horizontal angle from center • transmitter at 38Hz and at 30° vertical angle from center 455KHz: • transmitter at 455Hz and at 45° horizontal angle from center • transmitter at 455Hz and at 45° vertical angle from center Mounting: Mounts into US-style single-gang enclosures and most International single-gang enclosures. Dimensions (HWD): 4.46" x 2.71" x .57" (113.28 mm x 68.83 mm x 14.48 mm) Weight: .15 lbs (.07 kg) Included Accessories: Phoenix Connector (41-5045) Mounting Frame Faceplate IR Cover FIG. 2 Location of key components on the Mio Modero IR circuit board Switch 1 2 3 4 5 6 7 8 Value 1 2 4 8 16 32 64 128 FIG. 3 Example Device DIP Switch set to 129 Wiring Specifications @ 35 mA Maximum Wiring Length Wire Size Distance 18 AWG 3000 feet (914.40 m) 20 AWG 2121.64 feet (646.68 m) 22 AWG 1,322.75 feet (403.17 m) 24 AWG 833.80 feet (254.14 m) AXlink 3.5 mini Phoenix connector Notch to pry faceplate free (Rear Single) 8 position mini DIP switch Screw holes PWR+