AMX NCITE-813 Manuals

INSTRUCTION MANUAL INCITE DIGITAL VIDEO PRESENTATION SYSTEMS NCITE-813 NCITE-813A NCITE-813AC

QUICK START GUIDE NCITE-813/813A 8:1x3 Digital Video Presentation System Overview This guide applies to the following Incite NCITE-813 8:1x3 Presentation Switchers: •NCITE-813 (FG1901-10) •NCITE-813A (FG1901-12) The purpose of this document is to illustrate how to set up a device in its simplest configuration by a trained technician. What?s in the Box? The following items are included with the NCITE-813: •(1) Power Cord, Universal • (2) Mounting Brackets (1 RU) • (4) #6-32 x 1/4” screws • (4) rubber feet • (2) 2-pin 5mm connectors (NCITE-813A only) • (2) 3-pin connectors • (11) 5-pin connectors Environmental Requirements The environmental requirements for the NCITE-813/813A are as follows: • Operating Temperature: 32° F (0° C) to 104° F (40° C) • Storage Temperature: 4° F (-15° C) to 140° F (60° C) • Operating Humidity: 5% to 85% RH Getting Connected Once the device is powered on, you can connect to it through its IP address. NOTE: The device fully supports IPv6 network addressing. If the LAN port is con- nected to an IPv6 capable network it will self select an appropriate IPv6 address based on the discovered address parameters of the network to which it’s attached. Using the Front Panel Buttons You can access the configuration settings for the device by using the MENU ON/OFF, SELECT, and navigational buttons on the front panel of the device. Pressing the MENU ON/OFF button opens the On-Screen menu (FIG. 1) on the connected output device. FIG. 1 ON-SCREEN MENU Press the SELECT button to change an audio/video setting while you are using the On-screen menu on the selected output device. When using the on-screen menu, use the navigational buttons to cycle through audio and video settings (depending on the menu.) Use the Navigational buttons to traverse the available options and change their values. FIG. 2 displays the navigational function of each button. Move up to next menu configuration parameter Decrease value, or change the state of the selected parameter Increase value, or change the state of the selected parameter Move down to next menu configuration parameter FIG. 2 NAVIGATION BUTTONS Locating the IP Address of the Device You can locate the IP address of the NCITE-813/813A by using the buttons on the front panel of the unit. You can find the IP address in the On-Screen Menu (OSM) on the video output connected to the presentation system. Perform these steps to locate the IP address of the unit: 1. Press the MENU ON/OFF button on the front panel of the unit to open the On-Screen menu. 2. Use the UP and DOWN navigational arrow buttons to navigate to the Network menu. 3. Arrow right once to access the options under the Network menu and view the IP address. Note the IP address for future reference. NOTE: You can use the Status menu to verify current TCP/IP settings using the UP and DOWN navigational buttons. Switching to Static or Dynamic IP Addressing To toggle between static or dynamic IP addressing, the controller cannot be currently booting or it must be in ID Mode. If these conditions are met, holding the ID pushbutton for 10 seconds changes the current IP addressing mode. Changing the IP Address Once You Are Connected Perform these steps to change the IP address once you are connected to the controller: NOTE: Ensure the PC you are using to connect to the controller has the latest version of NetLinx Studio 4.0 installed on it. 1. Set the IP address on your PC to the same network the controller is currently on. 2. In NetLinx Studio, select Diagnostics > Network Addresses from the menu bar to open the Network Addresses dialog. 3. Click Get IP Information to enable the fields for editing. 4. Enter the System, Device (0 for NetLinx Masters), and Host Name information. 5. To specify a network IP address, select Specify IP Address. 6. Enter the IP parameters into the available fields. 7. Click Set IP Information to retain the pre-reserved IP Address to the Master. 8. Click Reboot Device to finish assigning the IP address to the Master, and click OK to close the dialog. Default Settings The following sections list the default settings for the controller. Default User Names and Passwords The following table lists the default user names and passwords for accessing the device through NetLinx Studio or the WebConsole. Default IP Addresses The following table lists the default IP addresses for the NCITE-813/813A. DEFAULT USER NAMES AND PASSWORDS User Name Password NetLinx Studio netlinx password WebConsole administrator password DEFAULT IP ADDRESSES IP Address Subnet Static IP 192.168.1.3 255.255.255.0 ICSLAN 198.18.0.1 255.255.0.0 Link-local 169.254.x.y, where x and y are the least significant two octets of the MAC address.