AMX NXA-PDU-1508-8 Manuals

Installation Guide NXA-PDU-1508-8 Power Distribution Unit (110V/220V) Overview The NXA-PDU-1508-8 Power Distribution Unit (FG673-01) provides switching of mains power to each of eight ACRMS 2020 power outlets. The two built-in AxLink bus strips provide connectivity (AxLink data / power) for up to eight AxLink connections. Note: AMX recommends no more than 4 PDUs per master, due to AxLink addressing and bus traffic. Product Specifications SAFETY INSTRUCTIONS • There are NO user serviceable parts within the NXA-PDU-1508-8. • The NXA-PDU-1508-8 is intended for indoor use only. • DO NOT install or operate the NXA-PDU-1508-8 in an area where the ambient temperature exceeds 40ºC (104ºF) or falls below 0ºC (32ºF). • DO NOT install or operate the NXA-PDU-1508-8 in an area in which the ambient relative humidity exceeds 85% or an area that is prone to condensation. • DO NOT install or operate the NXA-PDU-1508-8 near water or in a location which may be prone to water seepage, dripping or splashing. • DO NOT place objects containing liquids on the NXA-PDU-1508-8. Power Cord Requirements The NXA-PDU-1508-8 ships with a power cord, except to those countries which prohibit the shipment of the power cord selected. When selecting a power cord for use in Japan, please consider the following: The NXA-PDU-1508-8 requires a type VCTF or HVCTF and 1.25 or 2.0 sq.mm jacketed power cord with connectors and plugs that are 125V-12A or 125V-15A rated should be used. Rack-Mounting Note: For safety, the PDU should be installed near the socket-outlet providing power (which must be easily accessible by the PDU's power cord). Before rack mounting the PDU, pay particular attention to the following factors: • Temperature: Since the temperature within a rack assembly may be higher than the ambient room temperature, check that the rack-environment temperature is within the specified operating temperature range. • Mechanical Loading: Do not place any equipment on top of a rack-mounted unit. • Circuit Overloading: Be sure that the supply circuit to the rack assembly is not overloaded. • Grounding: Rack-mounted equipment should be properly grounded. Particular attention should be given to supply connections other than direct connections to the mains. FIG. 1 NXA-PDU-1508-8 NXA-PDU-1508-8 Specifications Power: Note: The PDU auto- senses the voltage of the supplied power. • Powered via 110-220 VAC, 50/60Hz mains power on an IEC-320 C-14 connector • Required voltage = 110 to 220 VAC, 50/60Hz • Total Combined Current (including AxLink): 10A at 220V-240V 12A at 110V-120V • Idle power draw: 1.0W max AC Current: • 110-120VAC: Input: 15A Regulatory Derated Input Current (North America)12A @ 110 VAC 10A Max Load Per Outlet @ 110VAC 12A Max Combined Load @ 110VAC • 220-240VAC: Input: 10A @ 220 VAC 8A Max Load Per Outlet @ 220VAC 10A Max Combined Load @ 220VAC Overcurrent Notification: • 110-120VAC: Single Outlet: 10A Overall: 12A • 220-240VAC: Single Outlet: 8A Overall: 10A Front Panel Components: POWER LEDs (1-8): Eight green LEDs illuminate to indicate that the associated Power Outlet (#1 - #8) is in use. AXLINK Power Status LEDs: Two red LEDs illuminate to indicate when the associated AxLink Bus Strips (Bank 1 or Bank 2) on the PDU are in use. AXLINK STATUS LED: Green LED illuminates to indicate AxLink communication activity between the PDU and the NetLinx Master: • ON - power, no master connection • OFF - no power • Blink - powered, communicating with master RESET pushbutton: The RESET pushbutton serves as a momentary reset switch for the MASTER AxLink power connection, as well as a reset switch for the PDU itself: • Press/hold for 3 seconds: Resets the MASTER AxLink power connection (minimum 0.5 second toggle). Note: A master powered externally from the PDU will not be reset by the RESET pushbutton. • Press/hold for 17 seconds: Resets the PDU (similar to a full power- cycle of the unit). Rear Panel Components: AXLINK POWER connectors (8): A 13.5VDC, 6.5A power supply is provided for AxLink power. Eight 3.5mm (4-pin) AxLink captive-wire connectors provide power and data for up to eight AxLink connections. • AxLink power is switched in two banks of four outputs each. BANK 1 contains AxLink connectors 1-4 BANK 2 contains AxLink connectors 5-8 • The PDU provides up to 6.5A total across all AxLink outputs. MASTER connector 3.5mm Phoenix (4-pin) AxLink connector provides connectivity to the NetLinx Master (always on). TEMP (RTS) input: 3.5mm Phoenix (2 pin) connector provides connection to a Remote Temperature Sensor (RTS). CONFIG DIP Switch: Eight-position DIP switch sets the AxLink device address. RESET pushbutton AxLink STATUS LED AxLink BANK 1 POWER (Output 1-8 Status) LEDs Power Status LED AxLink BANK 2 Power Status LED Power Inlet AXLINK POWER Connectors MASTER AxLink Connector (to NetLinx Master Controller) TEMP (RTS) Input Connector Power Outlets 1-8 CONFIG DIP Switch top = BANK 1 (1-4) bottom = BANK 2 (5-8) 1 2 3 4 5 6 7 8 NXA-PDU-1508-8 Specifications (Cont.) Power Outlets (8): • Connector Type: IEC C-13, 12A/10A • Maximum allowable current on a single high-voltage output: 10A@110VAC / 8A@220VAC Power Inlet (1): • Connector Type: IEC C-14, 12A/10A 110-120VAC: 12A Input 220-240VAC: 10A Input Dimensions (HWD): • 1 3/16" x 17" x 9 11/16" (2.97cm x 43.18cm x 24.54 cm) • 1 RU Weight: 9 lbs (4.08 kg) Enclosure: Steel, black powder coated finish Environmental: • Operating Environment: 0°C - 40°C (32°F - 104°F) • Storage Environment: -10°C - 60°C (14°F - 140°F) • Relative Humidity: 5% - 85%, non-condensing Certifications: • CE • CB Scheme • UL • FCC • CSA • C-Tick Included Accessories: • Power Cord, NEMA 5-15P TO C13, 15A, 14/3, 6’ (64-0673-01) Note: See Power Cord Requirements below for details. • ENV-VST-TSO, Temperature Sensor (FG2050-22) • (2) Removable mounting brackets • (9) 4-pin, 3.5mm captive-wire connectors (41-5047) • (1) 2-pin captive-wire connector (41-5026) Other AMX Equipment: • ENV-VST-TSF, Flush Mount Temperature Sensor (FG2050-21) • CC-C13-C14: C13 to C14 Power Cable (FG10-673-01) • CC-C14-NEMA: C14 to NEMA Power Cable (FG10-673-02) FIG. 2 SAFETY INSTRUCTIONS FIG. 3 CLASS A NOTIFICATION