Andersen 400 Series Manuals

Product Series: 400 Series Product Type: Tilt-Wash Double-Hung Windows Half Insect Screen Installation and Removal Guide Screen will not stop child from falling out window. Keep child away from open window. Half insect screen can move up and down in the frame channel when latches are engaged. Slide insect screen down to sill. Parts Included: Position bug seal to top side of insect screen, as shown. Flip pull tab down. 1 2 Read these instructions before starting procedure. For additional information visit www.andersenwindows.com. For questions call 1-888-888-7020. Tools and Supplies Needed: Safety Glasses Phillips Screwdriver WARNING Use caution when working at elevated heights and around window and door openings. Follow the manufacturers’ instructions for ladders and scaffolding. Failure to do so could result in injury or death. “Andersen” and all other marks where denoted are trademarks of Andersen Corporation. ©2018 Andersen Corporation. All rights reserved. 0005475 BB-00 05/22/18 NOTICE WARNING (1) Half Insect Screen For non-white colors, fasten through the pre-drilled holes with screws provided. Non-white Insect Screens Only (Pile faces interior) (1) Bug Seal White OR Non-White with (2) #6 x 3/8" Screws

Non-Reinforced Joining Guide (Vertical) Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough strength to lift, carry and install window and door products to avoid injury and/or product damage. Use caution when working at elevated heights and around unit openings. Follow manufacturer’s instructions for safe use of ladder and/or scaffolding. Failure to do so may result in injury or death. Follow manufacturer’s instructions for safe operation of hand/power tools. Always wear safety glasses. Failure to do so may result in injury and/ or product damage. Every assembly and installation is different (windloads, structural support, etc.). Andersen strongly recommends consultation with an Andersen supplier or an experienced contractor, architect, or structural engineer prior to the assembly and installation of any Andersen product. For installation methods not covered in this guide, (i.e. through jamb) please visit the Architect Detail File on the web (www.andersenwindows.com). Andersen has no responsibility in regard to the post-manufactured assembly and installation of Andersen products. Congratulations! You have just purchased one of the many fine Andersen® products. Proper assembly, installation and maintenance are essential if the benefits of your Andersen product are to be fully attained. Therefore, please read and follow this instruction guide completely. If your abilities do not match this procedure’s requirements, contact an experienced contractor. You may direct any questions about this or other products to your local Andersen dealer, found in the Yellow Pages under “Windows” or call Andersen WindowCare® service center at 1-888-888-7020 Monday through Friday, 7 a.m. to 7 p.m. Central Time and Saturday, 8 a.m. to 4 p.m. Central Time. Thank you for choosing Andersen. •� Andersen® Installation Flanges DO NOT take the place of standard window and door flashing. Unit must be properly flashed and sealed with sealant, and full width drip cap for protection against water and air infiltration. Use non-reflective flashings. Highly reflective flashing tapes can raise the surface temperature of the vinyl to the point where vinyl deformation and product damage may occur. •� Do�not�apply�any�type�of�film�to�glass.��Thermal�stress�conditions�resulting�in�glass�damage�could�occur. •� Use�of�movable�insulating�materials�such�as�window�coverings,�shutters,�and�other�shading�devices�may�damage� glass and/or vinyl. In addition, excessive condensation may result causing deterioration of windows and doors. Unless specifically ordered, Andersen windows and doors are not equipped with safety glass, and if broken, could fragment causing injury. Many laws and building codes require safety glass in locations adjacent to or near doors. Andersen windows are available with safety glass that may reduce the likelihood of injury when broken. Information on safety glass is available from your local Andersen dealer. “Andersen” and all other marks where denoted are trademarks of Andersen Corporation. ©2003-2007 Andersen Corporation. All rights reserved. Non-Reinforced Joining Guide (Vertical) for Andersen® 400 Series Tilt-Wash Double-Hung, Picture, and Transom Windows 0004372 BB Revised 12/13/07 1