AndyMark Robot Competition Table Manuals

AndyMark Robot Competition Table Assembly Guide v1.0 10/7/20 Included Parts & Hardware Required Tools Mallet 1/8” Allen Wrench #2 Phillips Screwdriver 4X - Outer Section Wall 2X - Inner Section Wall 1X - East Wall 1X - West Wall 4X - Flat Head Screw 30X - Washer 22X - Spacer 2X - Outer Panel 1X - Inner Panel 8X - Dowel 1. Insert Dowels into Outer Panels Locate the two Outer Panels and 8 Dowels. Using a mallet or Light Duty Hammer, gently insert dowels into holes on the edge of each Outer Panel. Approximately half the dowel should protrude when fully inserted. The inner panel does not recieve any dowels. x8 For more information visit AndyMark.com/Table 30X - Screw 2X - Interconnect A 2X - Interconnect B Interconnect A Outer Section Panel Outer Section Side Wall Interconnect B Outer Section Side Wall West Wall 2. West Section Assembly 1X - Interconnect A 1X - Interconnect B 2X - Outer Section Side Wall 1X - West Wall 1. Align walls to the corresponding edges of panel with the fat side of the panel facing up. Each hole in the panel should line up with a corresponding hole or threaded insert in each wall. 1X - Outer Panel For more information visit AndyMark.com/Table 12X - Washer 12X - Screw 8X - Spacer 2. Insert the Interconnects into the walls so that it lines up with the holes in the wall and panel. Make sure the back of the angle is facing towards the inside of the table. Use a screw and washer to secure the wall and Interconnect to the panel. Leave these screws loose until all screws are installed. 3. Add a screw, washer and spacer to each of the remaining panel holes. Thread the screw into the threaded inserts in each side wall and leave loose until all the screws are installed. Screw Outer Section Side Wall Washer Interconnect B Screw Spacer Washer 4. Adjust the walls and ensure the outside edges of each wall are aligned with the edge of the base panel. Using an 1/8” allen wrench, secure wall sections to the base panel. Inner Section Panel Inner Section Wall Inner Section Wall 3. Center Section Assembly 2X - Inner Section Wall 1X - Inner Panel For more information visit AndyMark.com/Table 6X - Washer 6X - Screw 6X - Spacer 1. Align walls to edges of the inner panel with the fat side of the panel facing up. Each hole in the panel should line up with a corresponding hole or threaded insert in each wall. 2. Add a screw, washer and spacer to each of the 6 large panel holes. The 4 holes on the edge will be used in a later step. Thread the screw into the threaded insert and leave loose until all the screws are installed. Screw Spacer Washer 3. Adjust the walls and ensure the outside edges of each wall are aligned with the edge of the base panel. Using an 1/8” allen wrench, secure wall sections to the base panel.

4X - Flat Head Screw Bottom View Table Setup & Disassembly 1. Slide each section together. Ensure the dowel pins in each outer section ft into the holes on the center section. The latches will be closest to the north side of the table. 2. Secure sections together using 4X Flat Head Screws. These screws will ft in the countersunk holes on the four corners of the inner panel. For more information visit AndyMark.com/Table W E N S The AndyMark Robot Competition table can split into 3 sections for transportation and storage. Required Tools #2 Phillips Screwdriver Section Assembly For more information visit AndyMark.com/Table Practice and Tournament Setup For Practice, the table can be placed by itself on the foor or on a table or sawhorses to elevate it’s height. Ensure the weight of each section is supported underneath and the table is positioned so that it cannot easily fall or be tipped. For Tournament Play, two tables can be placed with their North walls touching and secured together with the latches on the East and West walls. Storage and Transportation The table is designed to be split into 3 sections for storage and transportation by removing the 4 Flat Head Screws and separating the sections. The Flat Head Screws can be re-threaded into the brackets to ensure they don’t get lost. To prevent damage and table warping, store in a dry environment free from extreme temperature changes.