Ariston OK 897E LSC X AUS Manuals

1 AUS OVEN OK 897E LSC X AUS OK 897E LC X AUS OK 897E LSC AUS OK 897E LC AUS Contents Installation, 2-3 Positioning Electrical connection Data plate Description of the appliance, 4 Overall view Control panel Display Start-up and use, 5-6 Oven structure Control panel lock Setting the clock Setting the minute minder Restoring the factory settings Standby Cooking modes, 7-10 Manual cooking modes Automatic cooking modes Programming cooking Practical cooking advice Cooking advice table Precautions and tips, 11 General safety Disposal Respecting and conserving the environment Care and maintenance, 12 Switching the appliance off Cleaning the appliance Cleaning the oven door Replacing the light bulb Troubleshooting, 13 Assistance, 14 English, 1 AUS Operating Instructions 2 AUS ! Before placing your new appliance into operation please read these operating instructions carefully. If the appliance is sold, given away or moved, please make sure the booklet is also passed on to the new owners so that they may benefit from the advice contained within it. ! Please keep these operating instructions for future reference. it contains important information on installation, operation and safety. Positioning ! Keep packaging material out of the reach of children. It can become a choking or suffocation hazard. (see Precautions and tips). ! The appliance must be installed by a qualified person in compliance with the instructions provided. Incorrect installation may damage property or cause harm to people or animals. Built-in appliances Use the appropriate cabinet to ensure that the appliance functions properly. • The panels adjacent to the oven must be made of heat-resistant material. • Cabinets with a veneer exterior must be assembled with glues which can withstand temperatures of up to 100°C. • To install the oven under the counter (see diagram) or in a kitchen unit, the cabinet must have the following dimensions: * Stainless steel models only ! The appliance must not come into contact with electrical parts once it has been installed. The indications for consumption given on the data plate have been calculated for this type of installation. Ventilation To ensure good ventilation, the back panel of the cabinet must be removed. It is advisable to install the oven so that it rests on two strips of wood, or on a completely flat surface with an opening of at least 45 x 560 mm (see figures). Centring and fixing Secure the appliance to the cabinet: • Open the oven door. • Remove the 2 rubber plugs covering the fixing holes on the perimeter frame. • Fix the oven to the cabinet using the 2 wood screws. • Replace the rubber plugs. ! All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool. 560 mm. 45 mm. Installation min. 20 mm min. 45 mm FAN ASSISTED MODE 597 mm. 595 mm. 22,5 mm.* 20,5 mm. 550 mm. 570 mm. 20 mm. 575-585 mm. 45 mm. 558 mm. min. 550 mm. min. 3 AUS Electrical connection ! Ovens equipped with a three-pole power supply cable are designed to operate with alternating current at the voltage and frequency indicated on the data plate located on the appliance (see below). Fitting the power supply cable 1. Open the terminal board by inserting a screwdriver into the side tabs of the cover. Use the screwdriver as a lever by pushing it down to open the cover (see diagram). 2. Install the power supply cable: loosen the cable clamp screw and the three screws for the wire contacts L-N- and then fix the wires underneath the heads of the screws, respecting the colour coding: Blue (N) Brown (L) Yellow-Green (see figure). 3. Fix the cable in place by fastening the clamp screw. 4. Close the terminal board cover. Connecting the power supply cable to the electricity mains Install a standardised plug corresponding to the load indicated on the data plate (see opposite). The appliance must be directly connected to the mains using an omnipolar switch with a minimum contact opening of 3 mm installed between the appliance and the mains. The switch must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the switch). The supply cable must be positioned so that it does not come into contact with temperatures higher than 50°C at any point (the back panel of the oven, for example). ! The installer must ensure that the correct electrical connection has been performed and that it is fully compliant with safety regulations. Before connecting the appliance to the power supply, make sure that: • The appliance is earthed and the plug is compliant with the law. • the socket can withstand the maximum power of the appliance, which is indicated on the data plate (see below); • the voltage is in the range between the values indicated on the data plate (see below); • the socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets. ! Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible. ! The cable must not be bent or compressed. ! The cable must be checked regularly and replaced by authorised technicians only (see Assistance). ! The manufacturer declines any liability should these safety measures not be observed. APPLIANCE SPECIFICATIONS width 43.5 cm height 41 cm depth 41 cm Volume* Dimension* 74 l Electrical connections voltage: 220 - 240 V~ 50/60 Hz maximum power absorbed 2600 W (see data plate) ENERGY LABEL Directive 2002/40/EC on the label of electric ovens. Standard EN 50304 Declared energy consumption for Forced convection Class – heating mode: ECO This appliance conforms to the following European Economic Community directives: 2006/95/EEC dated 12/12/06 (Low Voltage) and subsequent amendments – 2004/108/EEC dated 15/12/04 and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments - 2002/96/EC and subsequent amendments. 1275/2008 Standby/off mode width 45.6 cm height 41 cm depth 41 cm Volume** Dimension** 77 l * Only for models with drawn rails. ** Only for models with wire rails. N L 4 AUS Description of the appliance Overall view Control panel SELECTOR knob THERMOSTAT / TIMER knob DISPLAY TIMER icon MINUTE MINDER icon CONTROL PANEL LOCKED icon LIGHT icon CONTROL PANEL POWER BUTTON START / STOP Control panel RACK shelf DRIPPING PAN shelf GUIDE RAILS for the sliding racks position 5 position 4 position 3 position 7 position 6 position D position 2 position 1 Display TEMPERATURE and TIME numerical digits END OF COOKING icon CLOCK icon DURATION icon MINUTE MINDER icon Preheating / Residual heat indicator CONTROL PANEL LOCK indicator MODE icons