Autostart ASL-300 Manuals

Keyless Entry And Alarm System Notice The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either damage to the vehicle itself or to the Unit. This Unit must be installed by a certified technician using all safety devices supplied. Only registered technicians will be eligible to use the Autostart technical support telephone service. Please review the Installation Guide carefully before beginning any work. DOC: 1.05 April 12, 2006 TL Manufactured in Canada by Autostart _____________________ Installation Guide Table of Contents Included in the Kit........................... 1 Installation Points to Remember .. 2 Programmable Features.................. 2 Harness Description......................... 2 How to Flash the Hood Pin........... 4 Programming a Transmitter........... 4 Programming Options .................... 4 Siren / Horn Chirp Duration Adjustment........................................ 6 Dome Light Delay............................ 7 Retain Accessory Output............... 7 Zone 2 Disable Output .................. 7 Multi-car Operation........................ 7 Resetting the Module...................... 7 Diagnostics - Parking Lights Flash Rate ..................................................... 7 Closing Up......................................... 8 Included in the Kit Please review the installation guide before beginning the installation, especially the wiring diagram and the programming options. It is very important that you familiarize yourself with the programming and operation of the system, even if you have already installed an alarm system in the past. There are many great new features that may be overlooked if the manual is not read: you would therefore not maximize the unit’s potential. Prior to the installation, make sure that all the hardware components required to install the system are in the box. ™ The following is a list of components included in the kit: o 1 – Control unit. o 1 – 2-WAY 6-button LCD transmitter and 1 - FM Antenna (only for TW System) o 1 – 4-button transmitter for the TW system (2 transmitters for 1-Way System) o 1 – Siren o 1 – plug-in L.E.D o 1 – Hood-pin switch o 1 – plug-in valet button. o 1 – plug-in shock sensor o 1 – user guide o 1 – installation guide. ™ The kit also includes the following harnesses: o 1 – 2 pin Wire harness. o 1 – 5 pin Main harness. o 1 – 12 pin principal auxiliary harness o 1 – 3 pin connector cable P. 2 Installation Guide0 Installation Points to Remember o When working on a vehicle always leave a window open. o Never leave the keys in the car. Leave them on a workbench with a window rolled down. o If possible, remove courtesy light fuse to prevent battery drain. o Inspect vehicle for any body damage or electrical problems. o Make sure that all the switches and controls operate properly. o Verify that the vehicle starts and idles properly. o Never install control unit where it could interfere with normal operation or obstruct service technicians. o Do not disconnect the battery on vehicles equipped with air bags and anti-theft radios. o Always use a grommet when running wires into the engine compartment. o Never run wires through bare or sharp metal. o Always solder and tape all connections. o Never ground the control unit to the steering column of the vehicle. o When you probe /test the wires of a harness, make sure you check the plug-in connector. o The wires for the air bags aren’t always identified on the harness (split loom or a yellow tape). However they are always identified on the connector. o Keep the Transceiver away from other types of antennas (GPS/Onstar). o Make sure all security equipment is installed: the Valet switch, the hood pin and the warning label. Programmable Features The unit was designed with flexibility and OEM integration in mind. The system gives installers the output flexibility that every good installer is looking for; this unit can be customized and used for almost every possible application. With the integration of timed-latched and ON / OFF outputs, this unit can single-handedly control virtually any electrical system in the car! The programmable features are as follows: 1. Siren or OEM Horn Output • The system can be programmed either to control the OEM horn or to command an external high-power siren. 2. Siren / Horn Chirp Timing • This feature allows you to configure the duration of the horn/siren chirps generated by the system. The horn/siren chirp duration can be set to any length between 10 ms and 250 ms. 3. Ignition-Controlled Door Locks • OFF by default. This feature will LOCK all the Doors of the vehicle while the Ignition Key is in the IGNITION ON (RUN) position and only when all the doors are closed (there is no recurrence of this action). The unit will UNLOCK all Doors when the Ignition Key is turned back to the OFF position. • If Ignition Lock Only is selected, the system will only LOCK all Doors while the Ignition Key is in the IGNITION ON (RUN) position and only when all the doors are closed (there is no recurrence of this action). • If option Ignition Unlock Only is selected, the system will UNLOCK all Doors when the key is turned to the OFF position (provided that the Ignition key was in the IGNITION ON (RUN) position). 4. Passive or Active Arming • (Passive with a 1-min. time out by default.) The alarm system on this unit can be set to active mode (in which it will not arm itself automatically) or to passive mode (arms itself automatically) with a 1-minute timeout. 5. Door Lock Pulse Duration • (¾-sec. lock and ¾-sec. unlock pulses by default.) This system can be programmed to give either 3.5- sec. lock /unlock pulses (this is used to control vacuum door-lock system, for instance on Mercedes) or a single ¾ -sec. lock pulse with a double ¼-sec. unlock pulse (this is used for double-pulse disarm/unlock systems, as in the Maxima, Pathfinder, and Volkswagen…) 6. Relock • If you unlock the doors with the remote transmitter, but do not open any door or trunk within 60 seconds, the doors will automatically relock. Harness Description 5 PIN HARNESS Installation Guide P. 3 WIRE Wire colour Function Description 1 BLACK (-) CHASSIS GROUND INPUT This wire must be connected to bare, unpainted metal (the chassis or true body ground). It is preferable that you use a factory ground bolt rather than a self-tapping screw. 2 RED +12V POWER INPUT Connect to the +12 V power feed of the vehicle, at the Ignition harness. The source wire should have +12 V without Ignition key in the cylinder. 3 GREY (–) HOOD SWITCH INPUT Connect this wire to the installed hood pin switch supplied. 4 YELLOW / BLACK PARKING LIGHT INPUT Connect to ground or +12 V for polarity control on pin #5 5 YELLOW PARKING LIGHT OUTPUT Connect to parking lights circuit of the vehicle. This wire will give either a positive or a negative output; depending on the polarity of pin #4. 12 PIN HARNESS WIRE Wire colour Function Description 1 PINK (+) IGINITION INPUT Connect to the Ignition wire of the vehicle. The source wire should have +12 V with the ignition key in the IGNITION ON (RUN) and CRANK positions. 2 PURPLE NA 3 GREY / Light BLUE (-) TRUNK INPUT Connect to the wire that tests ground with trunk open 4 GREY / GREEN (-) NEGATIVE TRIGGER INPUT When connected to the wire that provides ground when remote started this input will cause the alarm system to ignore the ignition and shock sense while running by remote start. (Trigger alarm input — selected by Default) 5 WHITE / RED (+) SIREN OUTPUT This wire will give a positive output when an alarm intrusion has occurred. It will also give positive pulses when remotely locking or unlocking the system (Siren Mode must be selected – selected by Default) 6 WHITE / BLUE (-) HORN OUTPUT This wire will give a negative output when an alarm intrusion has occurred. It will also give negative pulses when remotely locking or unlocking the system (Horn Mode must be selected) 7 GREY / BLACK (-) DOOR TRIGGER INPUT Connect to the wire that tests ground with a door open. Note: This wire should monitor all the doors. 8 GREY / RED (+) DOOR TRIGGER INPUT Connect to the circuit of the car giving +12 V when a door is opened (usually the dome-light circuit). 9 BLACK / Light BLUE (–) AUX 1 output This wire will provide 500mA ground output depending on the configuration of Mode 1, Function 5 (see programming options) 10 BLACK / BROWN (–) AUX 2 output This wire will provide 500mA ground output depending on the configuration of Mode 1, Function 4 (see programming options) 11 BLACK / GREEN (–) AUX 3 output This wire will provide 500mA ground output depending on the configuration of Mode 1, Function 3 (see programming options) 12 BLACK / PINK (–) Zone 2 Disable Output (armed output) This wire will provide a constant 500mA output when the system is armed (locked by remote control). It can be connected to an external starter interrupt relay. This wire should be connected to a single pole double-throw relay: this wire will connect to pin 85 on the relay, and pin 86 will be connected to the ignition wire.

V1.00 TL October 18, 2005 WIRING SCHEMATIC WIRING SCHEMATIC Keyless Entry And Alarm System 1- PURPLE ........... (+) Starter Input 2- PURPLE ............ (+) Starter Output 1- BLACK ......................................... GROUND (-) 2- RED ...... ..................... +12V POWER INPUT (+) 3- GRAY ....................... HOOD SWITCH INPUT (-) 4- YELLOW / BLACK .. PARKING LIGHTS INPUT 5- YELLOW ............... PARKING LIGHTS OUTPUT PUSH-BUTTON VALET SWITCH PLUG-IN L.E.D. 12- BLACK/PINK .................. (-) Zone 2 Disable Output 11- BLACK/GREEN .............. (-) Aux 3 Output 10- BLACK/BROWN ............. (-) Aux 2 Output 9- BLACK/BLUE ....... (-) Aux 1 Output 8- GRAY/RED ........................ (+) Pos. Door Trigger Input 7- GRAY/BLACK ................... (-) Neg. Door Trigger Input 6- WHITE/BLUE .................... (-) Horn Output 5- WHITE/RED ...................... (+) Siren Output 4- GRAY/GREEN .................. (-) Negative Trigger Input 3- GRAY/LIGHT BLUE ......... (-) Trunk Input 2- PURPLE ............................ N/A 1- PINK .................................. (+) Ignition Input 3- BROWN ............. (-) Lock 2- N/A ..................... (+) 12V for INV-200 Module 1- GREEN .............. (-) Unlock 1-WAY ANTENNA WIRE 2-WAY ANTENNA CABLE *** Only available on 2-WAY System SHOCK SENSOR

Keyless Entry And Alarm System DOC: 1.04 TL April 12, 2006 Manufactured in Canada User Guide Table of Contents Introduction ....................................1 One-Way Transmitter Functionalities................................2 Transmitter Operation ....................2 Two-Way Transmitter Functions at a Glance.........................................3 LCD Transmitter Operation............3 Basic Vehicle Operation.................3 Transmitter Mode Selection ...........3 Parking Countdown........................4 Time or Alarm Clock Adjustments..4 Features Available on your System5 Relock doors..................................5 Panic Mode....................................5 Multi-car Operation.........................5 Temporary Chirp Delete.................5 Priority Door Access ......................6 Alarm Functions.............................6 Passive Arm Mode.........................6 Active Arm Mode ...........................6 Disarming and Unlocking Doors.....6 Starter Disable...............................6 To Arm the Starter Disable ............6 To Disarm the Starter Disable........6 Retain Accessory Output ...............7 System L.E.D. Flash Rate..............7 Valet Operation..............................7 Remote Valet Operation ................7 Parking Lights Flash Rate..............8 Introduction Congratulations on the purchase of your new alarm system by Autostart! Whether you have chosen a 1-way system or a 2-Way system, you can now have the peace of mind of knowing that your prized possession is now protected by a sophisticated, state of the art alarm system. Packed with many advanced features, this system will satisfy any one of your expectations of high-end commodity and security, without neglecting any standard feature commonly offered by entry-level systems. Please read carefully this user guide to get acquainted with the operation and the features of your alarm system. Some features require extra parts and installation labour, please contact your installation centre for more details. INDUSTRY CANADA USER NOTICE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. FCC USER NOTICE (U.S.A.): This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. P. 2 User Guide One-Way Transmitter Functionalities Picture serves as example only. 1. button: Locks the doors and arms the module (starter kill and alarm), or activates panic mode if the button is held down for 4 seconds. 2. button: Unlocks the doors and disarms the module (starter kill and alarm), or activates panic mode if the button is held down for 4 seconds. 3. button: a. To open the trunk: Press and hold for 3 sec. b. Silent arming or disarming: press the TRUNK button once, then press the LOCK or UNLOCK buttons within 3 seconds to lock or unlock the doors without chirp. 4. button: a. To activate the AUX 2 output: Press and hold. b. Car Finder (If programmed): this will cause the parking lights to flash once and the Horn or siren to chirp once Transmitter Operation BUTTON(S) to press FUNCTION • Locks doors • Arms starter kill (Not in Alarm Valet) • Dome light OFF (If programmed) • Unlocks driver’s door • Disarms starter kill (Not in valet) – rearm timer at 60 sec. • Dome light ON for 60 sec. or until ignition goes ON or LOCK pressed (If programmed) or (while siren sounding) • Mutes siren; system not disarmed. A second UNLOCK press is required to disarm, unless the passive arming mode with no TWO-STAGE disarm is selected. (2 times) • Unlocks all doors (If Priority door programmed) • AUX 2 or 1 flash and 1 chirp (If car finder was enabled) • Mutes siren — system not disarmed. (for 4 seconds) • Locks doors • Enter panic mode – siren ON for 60 sec, valet ends (for 4 seconds) • Unlocks doors • Enter panic mode – siren ON for 60 sec, valet ends (for 3 seconds) • AUX 3 output, system disarmed with 1-sec pulse (trunk mode) or toggle ON / OFF (in latch mode) • Mutes siren — system disarmed + (for 3 seconds) • Valet ON or valet OFF User Guide P. 3 Two-Way Transmitter Functionalities LCD Transmitter Operation Basic Vehicle Operation FUNCTION BUTTON PRESSED ICON BUZZER INSTRUCTIONS /DESCRIPTION Lock 1 beep Lock, arm and starter kill on (if ignition is on, alarm will not arm) Unlock 2 beeps Unlock, disarm and starter kill off Trunk or Aux 3 1 beep Trunk or Aux 3 output Aux 2 No 1 beep Aux 2 output Transmitter Mode Selection FUNCTION BUTTON PRESSED ICON BUZZER INSTRUCTIONS /DESCRIPTION POWER-SAVING MODE ( + ) Melody Press the UNLOCK button then press FUNCTION and LOCK simultaneously. VIBRATION MODE + Vibrates 4X ALARM CLOCK MODE ON/OFF + Melody Press once to switch the Alarm Clock ON Press twice to switch the Alarm Clock OFF Function Button: . Turns On the backlight . For accessing Multi-level functions . Activates Panic mode if pressed for more than 3 seconds UNLOCK Button: . Unlocks all Doors and disarms the Security system . Activates Panic mode if press for more than 4 seconds TRUNK Button: Activates the Trunk output (AUX3) LOCK Button: . Locks all Doors and arms the Security system . Activates Panic mode if pressed for more than 4 seconds Aux 2 Button: Activates the Aux 2 output or car finder (If enabled) AUXILIARY Button: . Use to select option 5 while in programming mode . Or to save settings while in Siren/Horn adjustment mode P. 4 User Guide Parking Countdown FUNCTION BY PRESSING ICON BUZZER INSTRUCTIONS / DESCRIPTION + 1 time Melody 10 MIN COUNT DOWN + 2 times Melody 20 MIN COUNT DOWN + 3 times Melody 30 MIN COUNT DOWN + 4 times Melody 60 MIN COUNT DOWN + 5 times Melody 90 MIN COUNT DOWN + 6 times Melody 120 MIN COUNT DOWN FOR PARKING COUNTDOWN + 7 times Current time Melody PARKING COUNT DOWN OFF Time or Alarm Clock Adjustments User Transmitter 1. Press and hold the FUNCTION button until a beep is heard. The backlight will turn on the moment the FUNCTION button is pressed. 2. Upon hearing the beep, release the FUNCTION button. .................................. is displayed 3. Press and hold the FUNCTION button once more. 4. Release the FUNCTION button when a beep is heard. .................................. is displayed 5. Press and hold the FUNCTION button once more until a beep is heard. 6. Release the FUNCTION button. .................................. is displayed 7. At that point, press and hold the FUNCTION button until 2 beeps are heard. .............The hour setting will starts to flash. Pressing the FUNCTION button 1X..................................................Adjust hour (current time) 2X..................................................Adjust minutes (current time) 3X..................................................Adjust hour (Alarm) 4X..................................................Adjust minutes (Alarm) 5X..................................................Melody selection for the ringing of the alarm 6X..................................................Activate (ON) / Deactivate (OFF) Alarm 7X..................................................Adjust hour (countdown) 8X..................................................Adjust minutes (countdown) 9X..................................................Melody selection for the countdown 10X................................................Activate (ON) / Deactivate (OFF) countdown a. Press the button to increase the value or to activate or deactivate a function or to toggle through the melodies. b. Press the button to decrease the value or to activate or deactivate a function or to toggle through the melodies. c. To save modifications, do not touch any buttons for approx. 10 to 15 seconds. There will be a beep and the display will return to the time.