AV-GAD AV-701 Manuals

EasyLoader End User Manual Downloaded from: http://www.guardianalarms.net

AV-701 & AV-706 Keypads INSTALLATION INSTRUCTIONS Item 4713 (A5DS) Description The AV-706 and AV-701 are 4-wire Remote Control Station and Programmer Keypad compatible with EasyLoaderTM Control Panels. AV-706 LCD keypad fits the Dublo & PRO alarm panels. The AV-706 and AV-701 keypads are easy to install and operate. Large 7-Segment (AV- 701) and high-contrast LCD (AV-706) display provides vivid readout for all control panel’s information and zone identification. For AV-706 model refer to the programming and setup manual. Installation Instructions Press Down firmly on both tabs and pull  Handle keypad with clean hands  Do not use unnecessary force in opening and closing the keypad  Pill off the protective sheet from upper panel after the installation is complete Step One: Opening the keypad Locate the two rectangular tabs on the top of the keypad (about 35 mm / 1.5 inches from each side). Press down on both tabs firmly and pull front panel of keypad toward you from the top (see Figure 1.) Figure 1: Opening the keypad Step Two: Mounting onto Wall Place the keypad on wall, at 1.5-1.8 meter high. Make sure the two “UP” arrows word, are upwards. Attach housing to wall with flat-head screws (use screws that are suitable for the wall material). Before affixing to wall, make sure all wires have been inserted through the opening in the rear housing. If wires come up from the floor, they may be inserted through the square slot on the left side of the rear housing. (Use a small screwdriver for opening the slot with a twisting action.) Step Three: Wiring Disconnect AC and Battery power before wiring. Insert wires through the opening in the rear housing. (Note maximum wire lengths in the following table. The AV- 706 keypad maximum wiring length is 200 meters.) Make sure keypad wires are as far away as possible from telephone and high power radio transmitter or other electrically “noisy” wires or appliances. For longer run distance use thicker wire, e.g. 1 mm2. It is recommended to run keypad wires separately in a 4 or 6 wire cable. Do not run telephone, sensors or main electric wires in the same cable or electric pipe. Keypad Function Alarm Panel Wire Terminals Terminal AV-4016 AV-4404 AV-4008 AV-4009 OR Data OR OR OR OR YE Strobe YE YE YE YE +12V + Power +12V +12V +12V +12V -12V - Power -V -V -V -V Max. Cable (6 x 0.5mm) length 150 meters 100 meters 100 meters 150 meters * 7 4 1 0 8 5 2 # 9 6 3 Siren Shunt Display Status Delay Delete Chime Test Program Reset Shunt Telephone ARMED STATUS SHUNT FIRE ZONE DISPLAY EASYLOADER AV-701 AV-GAD

AV-706 & AV-701 Keypads INSTALLATION INSTRUCTIONS Item 4713 (A5DS) Description The AV-706 and AV-701 are 4-wire Remote Control Station and Programmer Keypad compatible with EasyLoader Control Panels. AV-706 fits the Dublo & PRO alarm panels. The AV-706 and AV-701 keypads are easy to install and operate. Large 7-Segment (AV-701) and high-contrast LCD (AV-706) display provides vivid readout for all control panel’s information and zone identification. For AV-706 model refer to the programming and setup manual. Installation Instructions Press Down firmly on both tabs and pull  Handle keypad with clean hands  Do not use unnecessary force in opening and closing the keypad  Pill off the protective sheet from upper panel after the installation is complete Step One: Opening the keypad Locate the two rectangular tabs on the top of the keypad (about 35 mm / 1.5 inches from each side). Press down on both tabs firmly and pull front panel of keypad toward you from the top (see Figure 1.) Step Two: Mounting onto Wall Figure 1: Opening the keypad Place the keypad on wall, at 1.5-1.8 meters height. Make sure the two “UP” arrows word, are upwards. Attach housing to wall with flat-head screws (use screws that are suitable for the wall material). Before affixing to wall, make sure all wires have been inserted through the opening in the rear housing. If wires come up from the floor, they may be inserted through the square slot on the left side of the rear housing. (Use a small screwdriver for opening the slot with a twisting action.) Step Three: Wiring Disconnect AC and Battery power before wiring. Insert wires through the opening in the rear housing. (Note maximum wire lengths in the following table. The AV-706 keypad maximum wiring length is 200 meters.) Make sure keypad wires are as far away as possible from telephone and high power radio transmitter or other electrically “noisy” wires or appliances. For longer run distance use thicker wire, e.g. 1 mm2. It is recommended to run keypad wires separately in a 4 or 6 wire cable. Do not run telephone, sensors or main electric wires in the same cable or electric pipe. Keypad Function Alarm Panel Wire Terminals Terminal AV-2016 AV-2004/48 AV-3004/48 AV-2008 OR Data OR OR OR OR YE Strobe YE YE YE YE +12V + Power +12V +12V +12V +12V -12V - Power -V -V -V -V Max. Cable (6 x 0.5 mm) length 150 meters 100 meters 100 meters 150 meters * 7 4 1 0 8 5 2 # 9 6 3 Siren Shunt Display Status Delay Delete Chime Test Program Reset Shunt Telephone ARMED STATUS SHUNT FIRE ZONE DISPLAY EASYLOADER AV-701 AV-GAD