Avipas AV-1361 Manuals

Model: AV-1361 HD IP Video Conference Camera User Manual V1.1 Please Read this User Manual throughout before using. www.avipas.com

[Type here] Model: AV-1361 H.264 HD Video Conferencing Camera User Manual V1.1 (English) Please read this User Manual throughout before using. www.avipas.com

How to connect PTZ camera with AV-3104IP Please make sure that the camera and the keyboard are both powered, and they are connected with either a RS-232 (IN), RS422 or an Ethernet cable. 1. VISCA & PELCO-D/P (via RS232 or RS422 port) To properly set up the connection, you need to make sure that the camera and the keyboard are using the same protocol and baud rate. In order to do so: • CAMERA: Go to Camera menu (use IR remote): press “MENU” -> “SETUP” -> select 1) the protocol, i.e. “Pelco-D”; 2) Pelco-D (Pelco-P/VISCA) Address (camera address), i.e. “2”; 3) Baudrate, i.e. “9600” -> press “MENU” to go back and exit the camera menu. All settings will be saved automatically. • KEYBOARD: Go to Keyboard menu: Press【SETUP】-> push the joystick down to select the submenu, until “Setup 05/08” shows on the screen for Mode selection; Push the joystick rightward to choose the protocol: “PELCO”-> press the button on the joystick to enter, or press【ENTER】; On the screen, you’ll see default setting “Addr: 001, 2400 P-D” on the screen, where 001 is the current controlling camera number, 2400 is the baudrate, P-D stands for Pelco-D protocol. Meanwhile, 【CAM1】button will light up. In order to change the baudrate to be consistent with the one camera is using, press 【SETUP】again-> “Setup 01/06 Control Setup”-> press 【ENTER】 Push the joystick up/down to change the Address. In this case, 002, press【ENTER】 Push the joystick up/down to change the Protocol. In this case, PELCO-D, press【ENTER】 Push the joystick up/down to change the Baudrate. In this case, 9600, press【ENTER】 The screen will show “Ctrl Setup Address 003” automatically to set up the next camera. If you have multiple cameras connected, please repeat the steps above. Otherwise, press【ESC】to exit the setup page.

How to connect PTZ camera with AV-3104IP Please make sure that the camera and the keyboard are both powered, and they are connected with either a RS-232 (IN), RS422 or an Ethernet cable. 1. VISCA & PELCO-D/P (via RS232 or RS422 port) To properly set up the connection, you need to make sure that the camera and the keyboard are using the same protocol and baud rate. In order to do so: • CAMERA: Go to Camera menu (use IR remote): press “MENU” -> “SETUP” -> select 1) the protocol, i.e. “Pelco-D”; 2) Pelco-D (Pelco-P/VISCA) Address (camera address), i.e. “2”; 3) Baudrate, i.e. “9600” -> press “MENU” to go back and exit the camera menu. All settings will be saved automatically. • KEYBOARD: Go to Keyboard menu: Press【SETUP】-> push the joystick down to select the submenu, until “Setup 05/08” shows on the screen for Mode selection; Push the joystick rightward to choose the protocol: “PELCO”-> press the button on the joystick to enter, or press【ENTER】; On the screen, you’ll see default setting “Addr: 001, 2400 P-D” on the screen, where 001 is the current controlling camera number, 2400 is the baudrate, P-D stands for Pelco-D protocol. Meanwhile, 【CAM1】button will light up. In order to change the baudrate to be consistent with the one camera is using, press 【SETUP】again-> “Setup 01/06 Control Setup”-> press 【ENTER】 Push the joystick up/down to change the Address. In this case, 002, press【ENTER】 Push the joystick up/down to change the Protocol. In this case, PELCO-D, press【ENTER】 Push the joystick up/down to change the Baudrate. In this case, 9600, press【ENTER】 The screen will show “Ctrl Setup Address 003” automatically to set up the next camera. If you have multiple cameras connected, please repeat the steps above. Otherwise, press【ESC】to exit the setup page.