Axxess AX-ALOC618 Manuals

AX-ALOC608 INSTALLATION INSTRUCTIONS Wire Color & Function: The audio input wire colors are an EIA standard for car stereo applications as follows. INPUT HARNESS WHITE = LEFT Front (+) Input WHITE/BLACK = LEFT Front (-) Input GRAY = RIGHT Front + Input GRAY/BLACK = RIGHT Front (-) Input BLACK = Reference Ground (-) (REFERENCE GROUND OPTIONAL IF NOISE IS PRESENT) NOTE: Be sure that all audio input connections are polarized or in phase with each other. That is, the positive output wires from the audio source need to be connected to the corresponding positive input wires of the AX-ALOC608. The same goes for the negative audio wires. Failure to do this will result in poor bass response and low quality audio. Adjusting the AX-ALOC608 for maximum performance: After completing all of the necessary connections, turn the AX- ALOC608 adjustment pots all of the way down by rotating them completely counter-clockwise. Now, turn the stereo system on and adjust the main volume control on the stereo to approxi- mately ¾ maximum volume. Select one of the adjustment pots on the AX-ALOC608 and turn it slowly clockwise until you notice audio distortion and then stop. Turn the remaining pot to the same position as the previously adjusted pot. The audio set-up of the AX-ALOC608 is now complete and ready to be enjoyed.

AX-ALOC618 AX-ALOC618 AX-ALOC618 AX-ALOC618 AX-ALOC618 AX-ALOC618 INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Wire Color & Function: The audio input wire colors are an EIA standard for car stereo applications as follows. INPUT HARNESS WHITE = LEFT Front (+) Input WHITE/BLACK = LEFT Front (-) Input GRAY = RIGHT Front + Input GRAY/BLACK = RIGHT Front (-) Input BROWN = Reference Ground(-) (REFERENCE GROUND OPTIONAL IF NOISE IS PRESENT) NOTE: Be sure that all audio input connections are polarized or in phase with each other. That is, the positive output wires from the audio source need to be connected to the corresponding positive input wires of the AX-ALOC618. The same goes for the negative audio wires. Failure to do this will result in poor bass response and low quality audio. Adjusting the AX-ALOC618 for maximum performance: After completing all of the necessary connections, turn the AX- ALOC618 adjustment pots all of the way down by rotating them completely counter-clockwise. Now, turn the stereo system on and adjust the main volume control on the stereo to approxi- mately ¾ maximum volume. Select one of the adjustment pots on the AX-ALOC618 and turn it slowly clockwise until you notice audio distortion and then stop. Turn the remaining pot to the same position as the previously adjusted pot. The audio set-up of the AX-ALOC618 is now complete and ready to be enjoyed. Wire Color & Function: The audio input wire colors are an EIA standard for car stereo applications as follows. INPUT HARNESS WHITE = LEFT Front (+) Input WHITE/BLACK = LEFT Front (-) Input GRAY = RIGHT Front + Input GRAY/BLACK = RIGHT Front (-) Input BROWN = Reference Ground(-) (REFERENCE GROUND OPTIONAL IF NOISE IS PRESENT) NOTE: Be sure that all audio input connections are polarized or in phase with each other. That is, the positive output wires from the audio source need to be connected to the corresponding positive input wires of the AX-ALOC618. The same goes for the negative audio wires. Failure to do this will result in poor bass response and low quality audio. Adjusting the AX-ALOC618 for maximum performance: After completing all of the necessary connections, turn the AX- ALOC618 adjustment pots all of the way down by rotating them completely counter-clockwise. Now, turn the stereo system on and adjust the main volume control on the stereo to approxi- mately ¾ maximum volume. Select one of the adjustment pots on the AX-ALOC618 and turn it slowly clockwise until you notice audio distortion and then stop. Turn the remaining pot to the same position as the previously adjusted pot. The audio set-up of the AX-ALOC618 is now complete and ready to be enjoyed. Wire Color & Function: The audio input wire colors are an EIA standard for car stereo applications as follows. INPUT HARNESS WHITE = LEFT Front (+) Input WHITE/BLACK = LEFT Front (-) Input GRAY = RIGHT Front + Input GRAY/BLACK = RIGHT Front (-) Input BBROWN = Reference Ground(-) (REFERENCE GROUND OPTIONAL IF NOISE IS PRESENT) NOTE: Be sure that all audio input connections are polarized or in phase with each other. That is, the positive output wires from the audio source need to be connected to the corresponding positive input wires of the AX-ALOC618. The same goes for the negative audio wires. Failure to do this will result in poor bass response and low quality audio. Adjusting the AX-ALOC618 for maximum performance: After completing all of the necessary connections, turn the AX- ALOC618 adjustment pots all of the way down by rotating them completely counter-clockwise. Now, turn the stereo system on and adjust the main volume control on the stereo to approxi- mately ¾ maximum volume. Select one of the adjustment pots on the AX-ALOC618 and turn it slowly clockwise until you notice audio distortion and then stop. Turn the remaining pot to the same position as the previously adjusted pot. The audio set-up of the AX-ALOC618 is now complete and ready to be enjoyed. Wire Color & Function: The audio input wire colors are an EIA standard for car stereo applications as follows. INPUT HARNESS WHITE = LEFT Front (+) Input WHITE/BLACK = LEFT Front (-) Input GRAY = RIGHT Front + Input GRAY/BLACK = RIGHT Front (-) Input BROWN = Reference Ground(-) (REFERENCE GROUND OPTIONAL IF NOISE IS PRESENT) NOTE: Be sure that all audio input connections are polarized or in phase with each other. That is, the positive output wires from the audio source need to be connected to the corresponding positive input wires of the AX-ALOC618. The same goes for the negative audio wires. Failure to do this will result in poor bass response and low quality audio. Adjusting the AX-ALOC618 for maximum performance: After completing all of the necessary connections, turn the AX- ALOC618 adjustment pots all of the way down by rotating them completely counter-clockwise. Now, turn the stereo system on and adjust the main volume control on the stereo to approxi- mately ¾ maximum volume. Select one of the adjustment pots on the AX-ALOC618 and turn it slowly clockwise until you notice audio distortion and then stop. Turn the remaining pot to the same position as the previously adjusted pot. The audio set-up of the AX-ALOC618 is now complete and ready to be enjoyed. Wire Color & Function: The audio input wire colors are an EIA standard for car stereo applications as follows. INPUT HARNESS WHITE = LEFT Front (+) Input WHITE/BLACK = LEFT Front (-) Input GRAY = RIGHT Front + Input GRAY/BLACK = RIGHT Front (-) Input BROWN = Reference Ground(-) (REFERENCE GROUND OPTIONAL IF NOISE IS PRESENT) NOTE: Be sure that all audio input connections are polarized or in phase with each other. That is, the positive output wires from the audio source need to be connected to the corresponding positive input wires of the AX-ALOC618. The same goes for the negative audio wires. Failure to do this will result in poor bass response and low quality audio. Adjusting the AX-ALOC618 for maximum performance: After completing all of the necessary connections, turn the AX- ALOC618 adjustment pots all of the way down by rotating them completely counter-clockwise. Now, turn the stereo system on and adjust the main volume control on the stereo to approxi- mately ¾ maximum volume. Select one of the adjustment pots on the AX-ALOC618 and turn it slowly clockwise until you notice audio distortion and then stop. Turn the remaining pot to the same position as the previously adjusted pot. The audio set-up of the AX-ALOC618 is now complete and ready to be enjoyed. Wire Color & Function: The audio input wire colors are an EIA standard for car stereo applications as follows. INPUT HARNESS WHITE = LEFT Front (+) Input WHITE/BLACK = LEFT Front (-) Input GRAY = RIGHT Front + Input GRAY/BLACK = RIGHT Front (-) Input BROWN = Reference Ground(-) (REFERENCE GROUND OPTIONAL IF NOISE IS PRESENT) NOTE: Be sure that all audio input connections are polarized or in phase with each other. That is, the positive output wires from the audio source need to be connected to the corresponding positive input wires of the AX-ALOC618. The same goes for the negative audio wires. Failure to do this will result in poor bass response and low quality audio. Adjusting the AX-ALOC618 for maximum performance: After completing all of the necessary connections, turn the AX- ALOC618 adjustment pots all of the way down by rotating them completely counter-clockwise. Now, turn the stereo system on and adjust the main volume control on the stereo to approxi- mately ¾ maximum volume. Select one of the adjustment pots on the AX-ALOC618 and turn it slowly clockwise until you notice audio distortion and then stop. Turn the remaining pot to the same position as the previously adjusted pot. The audio set-up of the AX-ALOC618 is now complete and ready to be enjoyed. INSTAX-ALOC618.pdf 1 11-12-29 下午2:12

AX-ALOC618 INSTALLATION INSTRUCTIONS Wire Color & Function: The audio input wire colors are an EIA standard for car stereo applications as follows. INPUT HARNESS WHITE = LEFT Front (+) Input WHITE/BLACK = LEFT Front (-) Input GRAY = RIGHT Front + Input GRAY/BLACK = RIGHT Front (-) Input BROWN = Reference Ground(-) (REFERENCE GROUND OPTIONAL IF NOISE IS PRESENT) NOTE: Be sure that all audio input connections are polarized or in phase with each other. That is, the positive output wires from the audio source need to be connected to the corresponding positive input wires of the AX-ALOC618. The same goes for the negative audio wires. Failure to do this will result in poor bass response and low quality audio. Adjusting the AX-ALOC618 for maximum performance: After completing all of the necessary connections, turn the AX- ALOC618 adjustment pots all of the way down by rotating them completely counter-clockwise. Now, turn the stereo system on and adjust the main volume control on the stereo to approxi- mately ¾ maximum volume. Select one of the adjustment pots on the AX-ALOC618 and turn it slowly clockwise until you notice audio distortion and then stop. Turn the remaining pot to the same position as the previously adjusted pot. The audio set-up of the AX-ALOC618 is now complete and ready to be enjoyed.