Beamz S2000 DMX Manuals

Ref. Nr. 160.500 S2000 DMX INSTRUCTION MANUAL GEBRUIKSAANWIJZING BEDIENUNGSANLEITUNG V1.1 - 2 - Warning: - The smokemachine must be placed at least 100 cm away from inflammable materials such as curtains, books, etc. Make sure that the housing cannot be touched by accident. - For indoor use only. - During installation, nobody should stand beneath the mounting area. - Prior to the first use, have the unit checked by a qualified person. - The unit contains voltage carrying parts. DO NOT open the smokemachine - Never plug or unplug the unit with wet hands. - If the plug and/or mains lead are damaged, they need to be repaired by a qualified technician. - If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains outlet. It needs to be repaired by a qualified technician. - Only connect this unit to an earthed mains outlet of 230Vac/50Hz . - Always unplug the unit during a thunderstorm or when it is not in use. - If the unit has not been used for a longer period of time, condensation can occur inside the housing. Please let the unit reach room temperature prior to use. - When you unplug the unit from the mains always pull the plug, never the lead. - In order to prevent dropping of the unit, a safety fastening needs to be installed. This can be a solid chain, a steel cable, etc. which has to be fastened separately from the mounting bracket. - The supplied bracket is the main fixing and must be used to solidly mount the light effect. - In order to avoid accidents in public premises, the local legal requirements and safety regulations/warnings must be fulfilled. - Keep out of the reach of children. Safety Plug the smoke machine only in an earthed mains outlet or extension cord! ATTENTION: the powercord can only be replaced by an original replacement, supplied by Tronios. Be careful when filling the fluid tank. First of all, unplug the mains lead! Then unscrew the cap on the tank and fill it by means of a funnel. Only use the original Beamz smoke fluid which is environmental friendly and, if used correctly, leaves no residues. Do not obstruct the openings on top of the case to guarantee a good ventilation. The heating element of the smoke machine generates heat which needs to be removed. Don’t put any objects on the smoke machine. Installation and Use Unpack the fog machine. Do not connect yet the net cable. Connect the lead of the manual control with the 3- pin plug at the rear of the smoke machine. Fill the fluid tank by means of a funnel. Connect the remote control with the Remote Control-socket. Plug the unit into a mains outlet. The heating element is automatically switched on. Depending on the room temperature, it takes about 8 minutes until the working temperature is reached, during this time the display shows “Warming Up”. When the machine is ready for fogging, the display shows "Ready To Fog". The remote interface allows to customize fog machine functions by adjusting fogging volume, duration, interval and LED color. Description of the Remote control: 1. LCD-Display 2. Menu button 3. Up-/Down buttons 4. Timer button 5. Volume-Lock button 6. Manual button - 3 - Settings Via the Menu key (2), you can adjust the desired settings. After pressing the menu, the display shows the following settings: 1. Man Vol Out xxx%. Adjust the manual volume output within the range of 0% to 100% by means of the Up/Down keys. 2. Interval Set xxxS Adjust the interval between each fog emission within the range of 1 to 100S by means of the Up-/Down keys. 3. Duration Set xxxS Adjust the duration of each fog emission within the range of 1 to 100S. 4. Volume Out xxx% Adjust the volume output during the timer function within the range of 0-100% 5. DMX 512 #xxx Adjust the DMX address for DMX control. 6. Wind For Class xx NO FUNCTION for this smoke machine 7. Angel Set xx% NO FUNCTION for this smoke machine 8. LED Pro Set xx Adjust the LED program within the range of 0 to 11. 9. LED Spe xxx Adjust the LED speed/strobe/fade of the LED program mode 10. Temper Max:xxx Adjust the maximum heating temperature of the heating element, adjustable between 285° - 330°C. 11. LED Sync Set Yes/No Adjust the LED mode. Yes=LEDs work together with the smoke output, NO=LEDs are always on. 12. Temper Min:xxx Adjust the minium heating temperature of the heating element, adjustable between 260° - 310°C. Timer control Press the Timer key (4) to activate the timer function. The display shows the adjusted interval and the device counts the seconds down to "0". After that, the fog emission is triggered at the volume adjusted under "Timer Out". The duration depends on the settings adjusted under "Duration Set". If you wish to deactivate the timer function, press the Timer key once more. Manual control (locked) Press the Lock switch (5) for immediate triggering of the fog emission at the volume adjusted under "Volume Out". Press the Volume switch once more in order to stop the fog emission. Manual control (100% output) Press the Manual key for immediate triggering of the fog emission at 100 % volume. Let the Manual key loose in order to stop the fog emission.