Blaupunkt DC-S1 Manuals

Wireless Door Contact (DC-S1) PPaarrttss DDeessccrriippttiioonn 1. LED indicator 2. Learn/Test Button Press the button to transmit a learn/test code and enter Test mode for 3 minutes. The LED will light up whenever Door Contact is triggered under Test mode 3. Supervision Enable/Disable Jumper Switch (JP2) 4. Tamper Switch The Tamper switch protects the Door Contact from unauthorized removal from mounted surface. 5. Battery Comparment 6. Knockouts 7. Battery Insulator 8. Rib Mark 9. Magnet PPaacckkaaggee CCoonntteenntt 1 x Door Contact 4 x wall plugs and screws 2 x adhesive pads 1 x 3V 1/2AA lithium battery (pre-installed) . Put the Control Panel into learning mode, then press the learn button to transmit learn code. Please refer to Control Panel manual to complete learn in process. The Door Contact has 2 knockouts on the inside of the back cover where plastic is thinner for wall mounting. 1. The Door Contact should be mounted on the door/window frame, while the magnet should be mounted on the door/window as shown in the picture below. The Door Contact has Rib Mark on one side to mark the position of the internal magnetic switch. The Rib Mark must be aligned with the magnet when mounted, the gap between the Door Contact and the magnet should be no more than 15 mm. 2. Drill holes into the wall using the knockouts as template, then fix the Door Contact base onto the wall with the screws and plugs provided. Alternatively, you can also use the double side adhesive tape provided to glue the Door Contact on the frame. 3. Replace the Door Contact cover onto the base. When mounting the Door Contact, please take note of the following points:  Mount as high as possible  Do not aim a PIR sensor at this window  Do not mount on metallic surface TTeesstt M Mooddee Press the Test Button to enter Test mode for 3 minutes. Under Test mode, the LED indicator will light up every time the Door Contact is triggered. Supervision Enable/Disable Jumper Switch (JP2) If enabled, the PIR sensor will transmit supervision signal to Control Panel periodically for the sensor to monitor PIR sensor condition. Jumper set to ON = supervision function is Disabled Jumper set to OFF = supervision function is Enabled (Default) O Oppeerraattiioonn LLeeaarrnniinngg IInnssttaallllaattiioonn Frame Door/ Window Jumper On The jumper link is inserted connecting the two pins Jumper Off if the jumper link is removed or parked on one pin.

Blaupunkt Competence Center Security Security Brand Pro GmbH Mondstrasse 2-4 85622 Feldkirchen, Germany E-Mail: [email protected] www.blaupunkt.com/service Follow the instruction in this document to setup and use the accessory. For further setting and operation details, please visit the Blaupunkt website http://www.blaupunkt.com/service to download the complete manual. DC-S1 / DC-S1B White/Brown EN | Door / Window Detector 1. LED Indicator 2. Learn Button 3. Knockouts 4. Battery Insulator 5. Rib Mark 6. Magnet DE | Funk- Tür/Fenstersensor 1. LED-Anzeige 2. Lern-/Testtaste 3. Aussparungen für Montage 4. Batterieisolator 5. Sensormarkierung 6. Magnet EN Follow instruction in this document to setup and use the accessory. For further setting and operation detail, please visit Blaupunkt website http://www.blaupunkt.com/service to download the complete manual. Getting Started 1. Pull out the battery insulator to activate battery. 2. Put the Control Panel into learning mode. 3. Press Learn Button to learn sensor. 4. Refer to Control Panel manual to complete learning process. Mounting Location  Mount the main body of the detector on the door/window frame, and the magnet on the door.window. Mount as high as possible  Do not aim a PIR Movement Detector at this door/window.  Do not mount on metallic surface. Installation 1. Break through knockouts on back cover of main body. 2. Drill holes into the door/window frame using the knockouts as template. 3. Fix the back cover onto the wall with the screws and plugs provided. 4. Replace the front cover on the back cover 5. Align the magnet with the Rib Mark on the main body; screw the magnet onto the door/ window. The gap between the main body and the magnet should be no more than 15 mm.  Instead of screw mounting, you can also use the double side adhesive tape included in the package to install the accessory. Battery: 1 x 3V lithium battery (Pre-inserted) Radio: 868 MHz DE Befolgen Sie diese Anleitung zur Einrichtung und Bedienung des Funk-Tür/Fenstersensors. Weitere Einzelheiten finden Sie in der vollständigen Betriebsanleitung unter http://www.blaupunkt.com/service . Inbetriebnahme 1. Batterieisolator herausziehen, um Batterie zu aktivieren. 2. Die Alarmzentrale in den Einlern-Modus bringen. 3. Lern-/Testtaste drücken, um den Sensor einzulernen. 4. Siehe Anleitung Alarmzentrale, um Einlernvorgang zu beenden. Montageort  Möglichst hoch anbringen. Sensor am Tür- /Fensterrahmen, den Magneten auf der Tür oder dem Fenster montieren.  Keinen Bewegungsmelder auf diese Tür/dieses Fenster richten!  Nicht auf metallischen Ober- flächen montieren. Montage 1. Aussparungen durchdrücken und als Schablone zur Markierung der Bohrlöcher verwenden. 2. Löcher in den Tür-/Fenster- rahmen bohren. 3. Unterseite mit mitgelieferten Dübeln und Schrauben montieren. 4. Gehäuse schließen. 5. Den Magneten in Höhe der Sensormarkierung ausrichten und an Tür/Fenster schrauben. Abstand zum Sensor: max. 15 mm.  Die beiden Teile können auch ohne Schraubmontage mit dem beiliegenden doppel- seitigen Klebeband montiert werden. Batterie: 1 x 3 V Lithiumbatterie (werksseitig eingelegt) Radio: 868 MHz FR Suivre les instructions de cette notice pour enregistrer le détecteur. Pour plus d’informations, rendez-vous sur http://www.blaupunkt.com/service pour télécharger la notice complète. Installation 1. Retirer la languette de protection de la pile. 2. Si le détecteur ne fait pas partie du kit, suivre les étapes ci- dessous pour enregistrer le détecteur dans la centrale. Si le détecteur est déjà inclus dans le kit, passer les étapes 3 à 5. 3. Mettre la centrale en mode Enregistrement. 4. Appuyer sur le bouton. 5. Se référer à la notice de la centrale pour finir l’enregistrement. Emplacement  Installer le détecteur sur le cadre et l’aimant sur l’ouvrant de la porte / fenêtre. L’installer le plus haut possible.  Ne pas installer près d’un détecteur de mouvement.  Ne pas installer sur une surface métallique. Installation 1. Percer les pré-trous. 2. Fixer la face arrière du détecteur. 3. Refermer le détecteur. 4. Aligner l’aimant avec le repère sur le détecteur. L’écart entre l’aimant et le détecteur ne doit pas dépasser 15 mm.  Il est possible d’utiliser la bande adhésive double face fournie pour fixer l’aimant et le détecteur mais nous vous recommandons de le visser. Pile : 1 x pile 3V Lithium (déjà insérée) Radio: 868 MHz FR | Contact d’ouverture 1. Voyant 2. Bouton 3. Pré-trous 4. Languette pile 5. Repère aimant 6. Aimant IT | Rivelatore Porta/Finestra 1. Indicatore LED 2. Tasto Apprendimento 3. Predisposizioni 4. Isolatore Batteria 5. Fascia di Marcatura 6. Magnete ES | Detector de puerta/ventana 1. Indicador LED 2. Botón de registro 3. Orificios ciegos 4. Aislante de batería 5. Marca para imán 6. Imán PT | Porta / janela Detector 1. LED Indicador 2. Saiba Botão 3. Nocautes 4. Bateria Isolador 5. Rib Mark 6. Ímã IT Per installare e configurare questo accessorio, seguire le istruzioni in allegato. Per avere ulteriori settaggi e dettagli sul suo funzionamento, visitate il sito http://www.blaupunkt.com/service per scaricare il manuale completo. Guida Introduttiva 1. Rimuovere la placchetta isolante per attivare la batteria. 2. Mettere il Pannello di Controllo in modalità apprendimento. 3. Premere il Pulsante di Apprendimento per far apprendere il sensore. 4. Consultare il manuale del Pannello di Controllo per completare il processo di apprendimento. Posizione di Montaggio  Montare il corpo principale del rivelatore sul telaio della porta/finestra, e il magnete sulla porta/finestra. Montare più in alto possibile  Non puntare un Sensore di Movimento PIR verso questa porta/finestra.  Non montare su una superficie metallica. Installazione 1. Rompere le predisposizioni per I fori tassello sulla copertura posteriore del corpo principale. 2. Trapanare i buchi sul telaio della porta/finestra usando le predisposizioni come sagoma. 3. Fissare la copertura posteriore sul muro con le viti e i plug in dotazione. 4. Riposizionare la copertura frontale su quella posteriore. 5. Allineare il Magnete con la fascia di marcatura sul corpo principale; avvitare il magnete sulla porta/finestra. Il dislivello tra il corpo principale e il magnete non deve superare i 15 mm.  Per installare l’accessorio, si può anche usare il biadesivo incluso nella dotazione al posto delle viti. Battery: 1 batteria al litio da 3V (Pre-inserita) Radio: 868 MHz ES Siga las instrucciones en este documento para instalar y usar este accesorio. Para más detalles por favor visite la página web de Blaupunkt http://www.blaupunkt.com/service para descargarse el manual completo. Comenzando 1. Retire el aislante de la bacteria para activar la bateria. 2. Ponga el panel de control en modo registro. 3. Presione cualquier botón para registrar el control remoto. 4. Consulte el manual del panel de control para terminar el registro. Donde instalar  Instale el detector en el marco de la puerta/ventana y el imán en la puerta/ventana. Móntelo lo más alto posible.  No apunte un detector PIR a la puerta/ventana.  No lo instale en superficies metálicas. Instalación 1. Rompa los orificios ciegos en la parte trasera del detector. 2. Taladre en el marco de la puerta/ventana usando los orificios como guía. 3. Fije la tapa trasera a la pared con los tornillos proporcionados. 4. Recoloque la tapa delantera en la tapa trasera. 5. Alinee el imán con la marca del detector y atornille el imán en la puerta/ventana. El espacio entre el detector y el imán no debe ser mayor de 15mm.  En vez de instalarlo con tornillos puede usar la cinta adhesiva de doble cara que está incluida con el dispositivo para instalar el accesorio. Batería: Batería de litio 1 x 3V (Pre-instalada) Radio: 868 MHz PT Siga as instruções deste documento para configurar e usar o acessório. Para mais definição e detalhes de operação, por favor, visite o site da Blaupunkt http://www.blaupunkt.com/service para baixar o manual completo. Começando 1. Retire o isolador da bateria para ativar bateria. 2. Coloque o Painel de Controle no modo de aprendizagem. 3. Imprensa Saiba botão para Aprender sensor. 4. Consulte o Manual de Controle Panel para concluir o processo de aprendizagem. Local de Montagem  Monte o corpo principal do detector na moldura da porta / janela, eo ímã na door.window. Montar o mais alto possível.  Não aponte um Movimento Detector PIR neste porta / janela.  Não monte na superfície metálica. Instalação 1. Romper nocautes na tampa traseira do corpo principal. 2. Faça furos na porta / janela do quadro usando os nocautes como modelo. 3. Fixe a tampa de volta para a parede com os parafusos e buchas fornecidos. 4. Recoloque a tampa frontal na tampa traseira. 5. Alinhe o ímã com o Mark Rib no corpo principal, parafuso do ímã para a porta / janela. A diferença entre o corpo principal eo íman deve ser não mais do que 15 mm.  Em vez de parafuso de montagem, você também pode usar a fita adesiva dupla face incluído no pacote para instalar o acessório. Bateria: 1 x bateria de lítio 3V (Pré-inserido) Radio: 868 MHz