Bradley Aerada 1100 Series S53-302 Manuals

Installation For Service Only Aerada™ 1100 Series Low Arc Faucet S53-302 Battery Infrared Metering Faucet (Center Shank with 4" Trimplate) 215-1525 Rev. G; EN 07-209 © 2007 Bradley Corporation Page 1 of 8 7/23/07 P.O. Box 309, Menomonee Falls, WI USA 53052-0309 PHONE 1-800-BRADLEY FAX (262) 251-5817 http://www.bradleycorp.com IMPORTANT! Read this entire installation manual to ensure proper installation, then file this manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances is the responsibility of the installer. Pressurized plumbing fixtures must be installed in accordance with manufacturer’s recommendations. The supply piping to these devices must be securely anchored to the building structure to prevent unnecessary movement of the installed device when operated by the user. Use extreme caution when installing the device to prevent damage to the exposed significant surface. Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. Flush water supply lines before making connections. DO NOT use pipe dope on any faucet or supply connections. Possible solenoid contamination could occur which will void any warranty. Teflon tape is the recommended sealant. The incoming water supply can be tempered or cold. An optional Bradley Vernatherm™ thermostatic mixing valve delivers tempered water at a temperature no greater than 105°F. The 1100 series faucet operates at a flowing water pressure of 20–80 PSI. A vandal-resistant .5 GPM flow restrictor ensures a constant flow rate at all pressures. Product warranties may be found under "Product Information" on our web site at www.bradleycorp.com. THIS SIDE UP Packing List Installation S53-302 Installation - For Service Only 2 7/23/07 Bradley Corporation • 215-1525 Rev. G; EN 07-209 Table of Contents Faucet Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Installation Mount the Faucet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Make Supply Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Sensor Range Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Cleaning and Maintenance Replacing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Cleaning the Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Vernatherm™ Mixing Valve . . . . . . . . . . . . . . . . . . . . . . . . .7–8 ADAPTER (OPTIONAL) 153-436 IN OUT ON OFF OPERATION BOX FILTER 153-437 TRIMPLATE ASSEMBLY (INCL. GASKET, STUDS, HEX NUTS & ANTI-ROTATIONAL SCREWS) 159-422 OPERATION BOX ASSEMBLY S08-366 SENSOR CABLE 269-1753 HOSE, BRAIDED 269-1752 FAUCET SENSOR ASSEMBLY (INCL. HEX NUTS, RUBBER WASHER & BRASS MTG. WASHER) S39-601 AERATOR ASSY. S05-173 www.bradleycorp.com SILICONE LUBRICANT 269-1776 Components for Model S53-302 3 Installation - For Service Only S53-302 Bradley Corporation • 215-1525 Rev. G; EN 07-209 7/23/07 Installation Supplies required: • Mounting screws for operation box • Pipe sealant • 1/2" NPS water inlet supply • Pipe fittings • OPTIONAL: 100–240 VAC adapter (plug-in adapter available from Bradley) Step 1: Mount the Faucet 1. Select the location on the deck where the faucet will be mounted. 2. Drill a 1-1/4" (32mm) diameter mounting hole in the deck (to allow for clearance of the mounting nut and sensor cable). 3. OPTIONAL TRIMPLATE: • Drill two 3/8" (10mm) dia. mounting holes on the deck as shown The holes should be spaced 4" (102mm) apart (measured from center to center) and aligned with the faucet mounting hole. • Thread the studs into the bottom of the trimplate. • Insert the trimplate studs into the deck holes and position the plate onto the deck. Secure the plate to the deck with the two 3/8" hex nuts and U-brackets provided. • Thread the two small anti-rotational mounting screws into the two holes in the underside of the trimplate and into the two holes in the bottom of the faucet body. Make sure screws are aligned with all holes. 4. Gently insert the faucet stud and sensor cable through the center hole in the deck. NOTE: Take care not to pinch the sensor cable. 5. Position the brass mounting washer onto the stud from beneath the deck. The sensor cable should be free from contact with the brass mounting washer. Screw the hex nut onto the faucet stud and secure the faucet to the deck by tightening the nut. Figure 1 FAUCET RUBBER GASKET SENSOR CABLE FAUCET STUD TRIMPLATE TRIMPLATE STUD (qty. 2) BRASS MOUNTING WASHER NUT 3/8" DIA. HOLE 1-3/4" DIA. HOLE DECK U-BRACKET ANTI-ROTATIONAL MOUNTING SCREW (qty. 2) S53-302 Installation - For Service Only 4 7/23/07 Bradley Corporation • 215-1525 Rev. G; EN 07-209 Installation Step 2: Make Supply Connections NOTE: Refer to Figure 2 when making supply connections. 1. Connect one end of the braided hose (supplied by Bradley) to the end of the faucet stud. 2. Connect the other end of Bradley’s braided hose to the operation box’s 1/2" NPS inlet fitting. 3. Connect one end of the braided hose (supplied by the installer) to the operation box’s inlet fitting. 4a. Connect the other end of the installer’s braided hose to the tempered or cold water inlet. 4b. FOR OPTIONAL VERNATHERM™ VALVE: Connect the other end of the installer’s braided hose to the Vernatherm™ mixing valve. IN OUT ON OFF www.bradleycorp.com Figure 2 FAUCET DECK SENSOR CABLE FAUCET STUD TRIMPLATE BRAIDED HOSE 1/2" NPS INLET FITTING