Broan 192 Manuals

1 IMPORTANT SAFETY INSTRUCTIONS WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOW- ING: 1. All electrical work must be done in accordance with local or national electrical code as applicable. For safety, this product must be grounded. If you are unfamiliar with methods of in- stalling electrical wiring, secure the services of a qualified elec- trician. 2. When wiring, servicing or cleaning this unit, turn off power and lock out service panel. Failure to do so could allow others or thermostat to turn on power unexpectedly which may cause fatal electrical shock. 3. To avoid electrical shock: • Do not install unit in a tub or shower enclosure or any loca- tion where it may come in contact with water. • Never place a switch where it can be reached from a tub or shower. 4. Do not install this unit in an area where chemicals and other flammables are stored or used. Explosion and fire may result. CAUTION 1. This product may ONLY be installed in a wall. Do not mount in any other position. 2. Install heater at least 12" from floor or any adjacent vertical surface. 3. Do not locate heater behind a door, furniture, drapes, etc., where the air flow to the unit would be restricted. 4. Provide heater with an appropriately-rated electrical circuit to prevent tripped breakers or blown fuses. 5. Do not connect heater to dimmer switch or speed control. 6. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc., off power unit. 7. Please read specification label on product for further informa- tion and requirement. INSTALLATION INSTRUCTIONS READ & SAVE THESE INSTRUCTIONS! Wall Heater MODELS: 192, 194, 198 FIGURE 1 PLAN THE INSTALLATION This heater is intended to be used to supply supplemental heat from a wall location in new or existing construction. Choose a location where edge of heater will be at least 12" from the floor or any adjacent vertical surface. The heater can be operated using its built-in thermostat or a re- mote thermostat (Choose either the Model 86W Line-Voltage ther- mostat or use the Model 82 Transfomer/Relay with an appropriate low-voltage thermostat.). The Model 85 Kit is available for surface- mount applications. Purchase these accessories separately. Plan to supply the heater with proper line voltage and appropriate power cable. NOTE: Power can be tapped from a nearby circuit depending on the heater wattage required and the amperage rating of the circuit. Heater can be converted to half-wattage to avoid overloading such circuits. MODEL VOLTS AMPS WATTS BTU/HR 192 240 8.33/4.17 2000/1000 6827/3413 194 240 12.50/6.25 3000/1500 10240/5120 198 240 16.67/8.33 4000/2000 13653/6827 DRYWALL THERMAL OVERLOAD GRILLE BUILT-IN THERMOSTAT HEATER HOUSING POWER CABLE Bold ratings are factory wired. See “OPTIONAL WIRING CONVERSIONS” section for wattage conversion instructions. Refer to FIGURE 1 Follow these basic steps when installing this heater: 1) Nail housing to studs. 2) Connect power cable. 3) Fasten heater assembly and grille to housing. Call 1-800-667-8721 anywhere in the US and Canada - www.bathroomsource.com ::bathroomsource.com Broan at ::bathroomsource.com is a division of kitchen::accessories U N L I M I T E D

READ AND SAVE THESE INSTRUCTIONS MODELS 192, 194 & 198 WALL HEATERS MODELOS 192, 194 y 198 CALENTADORES DE PARED LEA Y CONSERVE ESTAS INSTRUCCIONES WARNING 1. ALL ELECTRICAL WORK MUST BE DONE IN ACCORDANCE WITH LOCAL OR NATIONAL ELECTRICAL CODE AS APPLICABLE. FOR SAFETY, THIS PRODUCT MUST BE GROUNDED. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL WIR- ING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN. 2. WHEN WIRING, SERVICING OR CLEANING THIS UNIT, TURN OFF POWER AND LOCK OUT SERVICE PANEL. FAILURE TO DO SO COULD ALLOW OTHERS OR THERMOSTAT TO TURN ON POWER UNEXPECTEDLY WHICH MAY CAUSE FATAL ELECTRICAL SHOCK. 3. To avoid electrical shock: • DO NOT install unit in a tub or shower enclo- sure or any location where it may come in con- tact with water. • NEVER place a switch where it can be reached from a tub or shower. 4. DO NOT install this unit in an area where chemi- cals and other flammables are stored or used. Explosion and fire may result. CAUTION 1. This product may ONLY be installed in a wall. DO NOT MOUNT IN ANY OTHER POSITION. 2. Install heater at least 12" from floor or any adja- cent vertical surface. 3. DO NOT locate heater behind a door, furniture, drapes, etc., where the air flow to the unit would be restricted. 4. Provide heater with an appropriately-rated elec- trical circuit to prevent tripped breakers or blown fuses. (See chart on page 2). 5. DO NOT CONNECT HEATER TO DIMMER SWITCH OR SPEED CONTROL. 6. To avoid motor bearing damage and noisy and/ or unbalanced impellers, keep drywall spray, con- struction dust, etc., off power unit. 7. Please read specification label on product for fur- ther information and requirement. PLAN THE INSTALLATION This heater is intended to be used to supply supple- mental heat from a wall location in new or existing construction. Choose a location where edge of heater will be at least 12" from the floor or any adjacent vertical sur- face. The heater can be operated using its built-in thermo- stat or a remote thermostat (Broan Model 86W Line- Voltage thermostat). The Broan Model 85 Kit is avail- able for surface-mount applications. Purchase these accessories separately. Plan to supply the heater with proper line voltage and appropriate power cable. NOTE: Power can be tapped from a nearby circuit depending on the heater wattage required and the amperage rating of the circuit. Heater can be converted to half-wattage to avoid over- loading such circuits. INSTALLER: Leave This Manual With The Homeowner. HOMEOWNER: Use and Care Information on Page 3. INSTALADOR: Deje este manual con el dueño de casa. DUEÑO DE CASA: Información del uso y mantenimiento en la página 3. FIG. 1 GRILLE REJILLA BUILT-IN THERMOSTAT TERMOSTATO INCORPORADO HEATER HOUSING CAJA DEL CALENTADOR POWER CABLE CABLE DE ENERGIA ELECTRICA ADVERTENCIA 1. TODO EL TRABAJO ELECTRICO DEBE REALIZARSE DE ACUERDO CON LOS CODIGOS ELECTRICOS LOCALES Y/O NACIONALES CORRESPONDIENTES. PARA SU SEGURIDAD, ESTE PRODUCTO DEBE SER CONECTADO A TIERRA. SI USTED NO ESTA FAMILIARIZADO CON LOS METODOS DE INSTALACION DEL CABLEADO ELECTRICO, OBTENGA LOS SERVICIOS DE UN ELECTRICISTA COMPETENTE. 2. AL HACER EL CABLEADO, LIMPIEZA O DAR SERVICIO A ESTA UNIDAD, CORTE LA ENERGIA Y ASEGURE EL PANEL DE SERVICIO. SI NO HACE ESTO, ES POSIBLE QUE OTRAS PERSONAS O EL TERMOSTATO RESUMA LA ENERGIA EN FORMA INESPERADA, LO QUE PUEDE CAUSAR UN GOLPE ELECTRICO MORTAL. 3. Para evitar descarga eléctrica: • NO instale la unidad en una bañera o recinto de ducha. • NUNCA coloque un interruptor en un lugar que pueda ser alcanzado desde una bañera o ducha. 4. NO instale esta unidad en un área donde se almacenen o usen productos químicos u otros productos inflamables. De lo contrario, pueden producirse explosiones e incendios. CUIDADO 1. Este producto SOLAMENTE se puede instalar en una pared. NO LO MONTE EN NINGUNA OTRA POSICION. 2. Instale el calentador por lo menos a 30,48 cm de distancia del piso o de alguna superficie vertical adyacente. 3. NO COLOQUE el calentador detrás de una puerta, muebles, cortinas, etc., donde el flujo de aire a la unidad se encuentre restringido. 4. Proporcione al calentador un circuito eléctrico de capacidad apropiada, a fin de impedir la desconexión de disyuntores o quemado de fusibles. (Véase el diagrama en la página 2). 5. NO CONECTE EL CALENTADOR A UN VARIADOR DE LUZ O CONTROL DE VELOCIDAD. 6. Para evitar daños al cojinete del motor e impulsores ruidosos y/o desequilibrados, mantenga la unidad de energía alejada de rocíos de yeso, polvo de construcción, etc. 7. Para más información y requisitos, lea la etiqueta de especificación sobre el producto. PLANIFICACION DE LA INSTALACION Este calentador ha sido diseñado para proporcionar calefacción adicional desde el cielo raso en una construcción nueva o una ya existente. Escoja un lugar en que el borde del calentador se encuentre por lo menos a 30,48 cm de cualquier superficie vertical adyacente. Este calentador se puede poner en funcionamiento usando su termostato incorporado o un termostato a distancia (el termostato de tensión de línea Broan Modelo 86W). El conjunto Broan Modelo 85 está disponible para aplicaciones de montaje en superficie. Adquiera estos accesorios en forma separada. Proporcione al calentador la tensión de línea y cable de energía eléctrica apropiados. NOTA: La energía se puede tomar de un circuito cercano, lo que dependerá del vatiaje requerido del calentador y amperaje nominal del circuito. El calentador se puede convertir a mitad de vatiaje para evitar sobrecargar dichos circuitos. DRYWALL PARED DE YESO THERMAL OVERLOAD SOBRECARGA TERMICA