Canon VB-R11VE Manuals

The Operation Guide should be read before using the network camera. ENGLISH Network Camera Operation Guide / / / /

This Installation Guide is comprised of pages [1/2] and [2/2]. Please be sure to read the included "Safety Precautions" leaflet for correct use. After reading the Installation Guide, keep it in a safe location. There are two types of cameras: Hydrophilic Coating Model and Non-hydrophilic Coating Model. The hydrophilic coating models have a "hydrophilic coating model label" attached on the product's exterior cover. Hydrophilic Coating Models • VB-R13VE (H2)/VB-R12VE (H2)/VB-R11VE (H2)/VB-R10VE (H2) Non-hydrophilic Coating Models • VB-R13VE/VB-R12VE/VB-R11VE/VB-R10VE For handling the hydrophilic coating, be sure to read the included “Safety Precautions”. Do not remove the protective sheet of the hydrophilic coating model until installation of the camera is completed. * Some cameras are not available in certain countries or regions.  Caution Request a professional installer for all installation work. Never try to install the camera yourself. Doing so may result in unforeseen accidents such as dropping the camera or electric shock. Symbols used in this Installation Guide  : VB-R13VE (H2)/VB-R13VE  : VB-R12VE (H2)/VB-R12VE  : VB-R11VE (H2)/VB-R11VE  : VB-R10VE (H2)/VB-R10VE Items indicated in the Installation Guide [2/2] with this icon are not included with the camera, and should be provided by the user. Check Included Items Camera Warranty Card Before Using This Camera Safety Precautions Installation Guide (This document) Dedicated Wrench Waterproofing Tape Power Interface Cable (BK2-0036-000) I/O Interface Cable (BK2-0035-000) Power Interface Cable (Waterproof) (BK2-0039-000) LAN Connector Set (Waterproof) Accessories The following accessories can be purchased separately as necessary. Some accessories are not available in certain countries or regions. Ceiling Mounting Kit CM10-VB Dedicated accessory for attaching the camera to the ceiling. Wall Mounting kit WM10-VB Dedicated accessory for attaching the camera to a wall surface. 1.5inch Pipe Adapter PA10-15-VB Dedicated accessory used to install the camera to the end of pipe that extends from high ceilings, such as in big-box stores. Dome Unit DU10-S-VB Smoked dome cover (Hydrophilic coating is not treated). Canon AC Adapter PA-V18 Dedicated AC adapter for this camera. Part Names 9 11 10 12 13 14 15 Serial_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ MAC_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 4 6 8 1 2 3 5 1. External device I/O terminals / 2. Audio input terminal (Black) (common LINE IN and MIC IN) / 3. Audio output terminal (White) (LINE OUT) / 4. Power connection terminal / 5. LAN connector (RJ45, 100Base-TX) / 6. Attachment lock screws / 7. Power connection terminal / 8. LAN connector / 9. Dome case / 10. Reset switch*1 / 11. Reboot switch / 12. Lens / 13. LED (Orange) / 14. Memory card slot / 15. LED (Blue)*2 *1 Please refer to the “Operation Guide” for the method to reset the camera. *2 On: when powered on, during reboot / Off: during normal use Hydrophilic Coating Model label Protective sheet Notes for When and After Installing the Camera When Installing the Camera Installing the Camera Outdoors • Be sure to wrap with waterproofing tape. Please refer to the "Wrapping the Waterproofing Tape" cautions below for how to wrap. • Please be sure to use the included LAN Connector Set (Waterproof). • If connecting the camera to the composite pipe by wiring, bridge the gap using Ceiling Mounting Kit (sold separately) or Wall Mounting kit (sold separately). When connecting the pipe, apply silicon sealant to seal it tightly after attaching the pipe to prevent water getting in as necessary. Wrapping the Waterproofing Tape Properly waterproof the connections, as shown in the Installation Guide [2/2], using the waterproofing tape (included). If not properly waterproofed, it may result in water intrusion, thereby causing breakdown. • To prevent cable connections from shorting out, wrap each individual connection with insulating tape, and then wrap all of the cables with waterproofing tape. Please refer to the Installation Guide [2/2] for details on how to wrap the waterproofing tape. • The camera conforms to the dust-resistant/waterproof specification (IP66), however the cable ends that connect to external devices are not. Cable connections should be wrapped with waterproofing tape, if there are any chances that it may get wet. • Accessories for installation are not dust-proof/waterproof. Wrap the cable connections with the included waterproofing tape, even if they can fit within the optional unit, because there could be a chance of the cables getting wet. After Installing the Camera When the temperature within the camera is low (heater activation) When the camera is powered by a 24 V AC/ PoE+ power source, the heater unit can be used. The heater unit will be activated automatically when the temperature within the camera is low. The orange LED will be lit, until the camera has warmed up enough to start transferring video. Once the temperature within the camera has reached the level where it can transfer the video once again, the orange LED will turn off. Before Installing the Camera Separating the Camera and Attachment Note Please unhook the safety wire connected to the camera.    Removing and Attaching the Dome Case Attaching the Dome Case (1) Fix the screws in the dome case and attach the safety wire. (2) Align the dome case with the camera body. (3) Tighten the dome case screws with the dedicated wrench. Removing the Dome Case Loosen the screws holding the dome case in place with the dedicated wrench, and remove it. Loosen the screws on the dome case to detach the safety wire. Dedicated wrench Note When you use a memory card, remove the dome case and place it in the memory card slot (SD memory card, SDHC memory card, and SDXC memory card are available). The screws used for the dome case fall prevention safety wire and dome cover holder are as follows. Connecting the LAN Connector Set (Waterproof) Connect the LAN cable to the connector. 7.5 - 8.6 mm ( 0.30 - 0.34 in.) 6.1 - 7.5 mm ( 0.24 - 0.30 in.) 4.9 - 6.1 mm ( 0.19 - 0.24 in.) 14 - 16 mm (0.55 - 0.63 in.) 24 - 26 mm (0.94 - 1.02 in.)          Note • Align the wires with the terminal settings according to the 568B/568A color coded illustration, and insert them into the wire manager. • The LAN cable may not be able to be properly inserted or removed from the LAN connector, if the LAN Connector Set (Waterproof) is not used. The cable’s water resistance will not be maintained as well. Wire Manager 568B 568A Nominal diameter Length Head shape M3 6 mm (0.24 in.) pan head Network Camera / / / / / / / Installation Guide ENGLISH BIE-7249-000 1 2