Chip Hyde VISION 3D Manuals

INSTRUCTIONS FOR CHIP HYDE VISION 3D Copyright 2004 – Chip Hyde Products Chip Hyde Products 999 East Fry Boulevard Suite 316 Sierra Vista Arizona 85635 520 234 4848 www.chiphyde.com Liability Exclusion and Damages You have acquired a kit, which can be assembled into a fully working R/C model when fitted out with suitable accessories, as described in the instruction manual with the kit. However, we at Chip Hyde Products Inc. are not in a position to influence the way you build and operate your model, and we have no control over the methods you use to install, operate and maintain the radio control system components. For this reason we are obliged to deny all liability for loss, damage or costs which are incurred due to the incompetent or incorrect application and operation of our products, or which are connected with such operation in any way. Unless otherwise prescribed by binding law, the obligation of Chip Hyde Products Inc. to pay compensation is excluded, regardless of the legal argument employed. This applies to personal injury, death, damage to buildings, loss of turnover and business, interruption of business or other direct and indirect consequent damages. BY OPERATING THIS MODEL YOU ASSUME FULL RESPONSIBILITY FOR YOUR ACTIONS. It is important to understand that Chip Hyde Products Inc. is unable to monitor whether you follow the instructions contained in this instruction manual regarding the construction, operation and maintenance of the aircraft, nor whether you install and use the radio control system correctly. For this reason we at Chip Hyde Products Inc. are unable to guarantee or provide a contractual agreement with any individual or company that the model you have made will function correctly and safely. You, as operator of the model, must rely upon your own expertise and judgment in acquiring and operating this model. An R/C aircraft is not a toy! If misused, it can cause serious bodily harm and damage to property. Fly only in open areas, preferably AMA (Academy of Model Aeronautics) approved flying sites, following all instructions included with your radio and engine. Do not fly this or any other model airplane after consuming any alcohol and/or drugs (both legal and/or illegal). SUPPLIMENTARY SAFETY NOTES: Before every session check that all of the model’s working systems function correctly, and be sure to carry out a range check. The first time you fly any new model aircraft we strongly recommend that you enlist the help of an experienced modeler to help you check the model and offer advice while you are flying. He should be capable of detecting potential weak points and errors. Be certain to keep to the recommended CG position and control surface travels. If adjustments are required, carry them out before operating the model. Be aware of any instructions and warnings of other manufacturers, whose product(s) you use to fly this particular aircraft, especially engines and radio equipment. Please don’t ignore our warnings, or those provided by other manufacturers. They refer to things and processes, which, if ignored, could result in permanent damage or fatal injury. Contents of Vision 3D Assembly Manual 1. Introduction ......................................................................................................... 4 2. Intended Use....................................................................................................... 4 3. Warranty.............................................................................................................. 4 4. Kit Contents......................................................................................................... 5 5. Items Needed to Complete the Vision 3D ........................................................... 7 5.1 Components and Hardware Needed to Complete the Vision 3D ................ 7 5.2 Tools Needed to Complete the Vision 3D ................................................... 8 5.3 Adhesives Needed to Complete the Vision 3D ........................................... 8 6 Vision 3D Building Instructions............................................................................ 9 6.1 Overview and Useful Information ................................................................ 9 6.2 Covering...................................................................................................... 9 7 Wing Assembly ................................................................................................. 10 7.1 Fitting and Hinging the Ailerons ................................................................ 10 7.2 Aileron Servo Installation........................................................................... 12 8 Engine Installation............................................................................................. 16 8.1 Mounting the Engine ................................................................................. 16 8.2 Fitting the Ignition Module ......................................................................... 18 8.3 Fitting the Exhaust and Fibreglass Pipe Tunnel........................................ 18 9. Undercarriage and Tail Wheel Unit Installation................................................. 20 9.1 Undercarriage Installation ......................................................................... 20 9.2 Tail Wheel Unit Installation........................................................................ 20 10. Fin, Rudder and Rudder Servo/linkage Installation....................................... 21 10.1 Fin Preparation and Gluing ....................................................................... 21 10.2 Fitting and Hinging the Rudder.................................................................. 22 10.3 Rudder Servo and Control Linkage Installation......................................... 22 11 Horizontal Stabilizers and Servos/linkages Installation..................................... 24 11.1 Elevator Servos Installation....................................................................... 24 11.2 Fitting and Hinging the Elevators .............................................................. 24 11.3 Fitting the Horizontal Stabilizers................................................................ 25 11.4 Fitting the Elevator Control Rods and Ball Raced Horns........................... 26 12. Wing Retainer Installation ............................................................................. 27 12.1 Wing Retainer Method............................................................................... 27 18. Final Finishing and Checks ........................................................................... 36 19. Chip’s Recommended Control Throws.......................................................... 37 1. Introduction The Vision 3D is a highly aerobatic monoplane designed and sold by world renowned aerobatic RC pilot Chip Hyde - multiple USA National, World and TOC champion. The model is fully capable of both precision F3A type aerobatics and full blown more extreme 3-D aerobatics. The Vision 3D may be assembled rapidly due to plug-in wings and plug-in horizontal stabilizers. Not only does this make assembly at your flying site fast, but makes the model easy and accurate to construct. The wings and stabilizers slide onto pre-fitted tubes and are aligned by anti- rotation pins. There is a minimal amount of gluing and drilling required to complete the assembly. This greatly reduces the time to assemble the model and get you to your flying site. The Vision 3D can be disassembled and broken down into two wing panels, two stabilizer halves and a fuselage to facilitate transportation in almost any size of vehicle. The larger the vehicle, the less you will need to remove! The Vision 3D is designed for gas motors in the 50-cc category. The recommended motor is the DA 50 that is shown in the assembly instructions. The final choice of power plant is left up to the builder. A computer radio is recommended for the Vision 3D. This is primarily because then the Pilot can take advantage of the full capabilities of this model, using the various mixing and servo adjustments functions that are typically available. Either a single or a pair of servos may be used for each aileron. The allows either a single high torque servo to be used to drive each aileron, or in the event only lower powered servos are available; a pair may be used. 2. Intended Use The Vision 3D should not be regarded as a toy. This is an advanced aerobatic plane and is recommended for pilots who are well beyond the trainer-stage and are comfortable with flying at least an aerobatic sport plane. 3. Warranty Defective parts will be exchanged/replaced once the original item is returned at the owner’s expense. Contact Chip Hyde Products if you are located in North America or Probuild Aircraft if you are located in Europe.