Control 4 C4-KC240 Manuals

™ Warnings and Considerations WARNING! Turn OFF electrical power before installing or servicing this product. Improper use or installation can cause SERIOUS INJURY, DEATH or LOSS/DAMAGE OF PROPERTY. WARNING! This device must be protected by a circuit breaker (20A max). WARNING! Ground this device in accordance with the National Electric Code (NEC) requirements. DO NOT rely solely upon the yoke plate’s contact with a metal wallbox for adequate grounding. Use the device’s ground wire to make a secure connection to the safety ground of the electrical system. IMPORTANT! This device must be installed by a licensed electrician in accordance with all national and local electrical codes. IMPORTANT! If you are unsure about any part of these instructions, consult a qualified electrician. IMPORTANT! Use this device only with copper or copper-clad wire. Do not use aluminum wiring. This product has not been approved for use with aluminum wiring. IMPORTANT! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See “Troubleshooting.” IMPORTANT! Do NOT use a power screwdriver to install this device. If you do, you may overtighten the screws and strip them. Also, overtightening the screws may interfere with proper button operation. IMPORTANT! This is an electronic device with intricate components. Handle and install with care! Installation Instructions 1 Ensure that the location and intended use meet the following criteria: • When replacing a traditional 3-way switch, refer to the “Two-Location” sample wiring configurations provided in the appropriate load control device installation guide. • Install in accordance with all national and local electrical codes. • The range and performance of the wireless control system is highly dependent on the following: (1) distance between devices; (2) layout of the home; (3) walls separating devices; and (4) electrical equipment located near devices. 2 Turn off the mains electrical power at the consumer unit. To ensure the wires do NOT have power running to them, use an inductive voltage detector. NOTE: The wallbox wiring shown in this document is an example. Your wire colors and functions may differ. If you are not sure which wires are the Hot, Neutral, and Ground wires, have a trained electrician do the installation. 3 Prepare each wire. Wire insulation should be stripped back 7mm from the wire end (see Figure 1). Supported Model • C4-KC240 Wireless Configurable Keypad, 240V Introduction The Control4® Configurable Keypad is intended for use in a Control4 system. It installs in a standard wallbox using typical wiring standards and communicates to the Control4 system using a wireless connection. Box Contents • Configurable Keypad • Keycap Button Kit • Terminal Block • Warranty Card • Configurable Keypad Installation Guide (this document) • Keypad Buttons Installation Guide Specifications The specifications are described below. Model Number C4-KC240-xx Power Requirements 220VAC-240VAC +/-10% 50/60 Hz 36-48VDC This device requires a neutral AC connection. Power Consumption 240V: 480mW 36VDC: 430mW Environmental Operational Temperature 32˚ F - 104˚ F (0˚ C - 40˚ C) Humidity 5% to 95% non-condensing Storage -4˚ F - 158˚ F (-20˚ C - 70˚ C) Miscellaneous Control Communications ZigBee, IEEE 802.15.4, 2.4 GHz, 15-channel spread spectrum radio Wallbox Volume 4.75 cubic inches (77.8 cubic centimeters) Weight 0.12 lb. (0.05 kg) Shipping Weight 0.18 lb. (0.08 kg) Configurable Keypad Installation Guide

™ Warnings and Considerations WARNING! Turn OFF electrical power before installing or servicing this product. Improper use or installation can cause SERIOUS INJURY, DEATH or LOSS/DAMAGE OF PROPERTY. WARNING! This device must be protected by a circuit breaker (20A max). WARNING! Ground this device in accordance with the National Electric Code (NEC) requirements. DO NOT rely solely upon the yoke plate’s contact with a metal wallbox for adequate grounding. Use the device’s ground wire to make a secure connection to the safety ground of the electrical system. IMPORTANT! This device must be installed by a licensed electrician in accordance with all national and local electrical codes. IMPORTANT! If you are unsure about any part of these instructions, consult a qualified electrician. IMPORTANT! Use this device only with copper or copper-clad wire. Do not use aluminum wiring. This product has not been approved for use with aluminum wiring. IMPORTANT! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See “Troubleshooting.” IMPORTANT! Do NOT use a power screwdriver to install this device. If you do, you may overtighten the screws and strip them. Also, overtightening the screws may interfere with proper button operation. IMPORTANT! This is an electronic device with intricate components. Handle and install with care! Installation Instructions 1 Ensure that the location and intended use meet the following criteria: • When replacing a traditional 3-way switch, refer to the “Two-Location” sample wiring configurations provided in the appropriate load control device installation guide. • Install in accordance with all national and local electrical codes. • The range and performance of the wireless control system is highly dependent on the following: (1) distance between devices; (2) layout of the home; (3) walls separating devices; and (4) electrical equipment located near devices. 2 Turn off the mains electrical power at the consumer unit. To ensure the wires do NOT have power running to them, use an inductive voltage detector. NOTE: The wallbox wiring shown in this document is an example. Your wire colors and functions may differ. If you are not sure which wires are the Hot, Neutral, and Ground wires, have a trained electrician do the installation. 3 Prepare each wire. Wire insulation should be stripped back 7 mm (0.287 in.) from the wire end (see Figure 1). Supported Model • C4-KC240 Wireless Configurable Keypad, 240V Introduction The Control4® Configurable Keypad is intended for use in a Control4 system. It installs in a standard wallbox using typical wiring standards and communicates to the Control4 system using a wireless connection. Box Contents • Configurable Keypad • Keycap Button Kit • Terminal Block • Warranty Card • Configurable Keypad Installation Guide (this document) • Keypad Buttons Installation Guide Specifications The specifications are described below. Model number C4-KC240-xx Power requirements 220V AC to 240V AC +/-10% 50/60 Hz 36-48V DC This device requires a neutral AC connection. Power consumption 240V: 480mW 36V DC: 430mW Environmental Operational temperature 0 to 40 ˚C (32 to 104 ˚F) Humidity 5% to 95% non-condensing Storage -20 to 70 ˚C (-4 to 158 ˚F ) Miscellaneous Control communications Zigbee, IEEE 802.15.4, 2.4 GHz, 15-channel spread spectrum radio Wallbox volume 77.8 cubic centimeters (4.75 cubic inches) Weight 0.05 kg (0.12 lb.) Shipping weight 0.08 kg (0.18 lb.) Configurable Keypad Installation Guide