Control 4 LOZ-5S1-W Manuals

Wireless Outlet Switch Installation Guide Supported Models and Requirements LOZ-5S1-W Wireless Outlet Switch Graphical Symbols in this Guide The following symbols and their descriptions draw your attention to important safe practices and additional information that can help you avoid injury, death, or loss of material or time. WARNING! This indicates a potentially hazardous situation that, if not avoided, may result in death or serious injury. DO NOT IGNORE A WARNING! CAUTION! This indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. DO NOT IGNORE A CAUTION! IMPORTANT! This indicates information that will help you avoid damage to your equipment, loss of materials, or loss of time. PAY ATTENTION TO THESE IMPORTANT STATEMENTS! Specifications and Supported Fixtures This Wireless Outlet Switch plugs into a standard, earth-grounded (3-prong) electrical outlet and communicates with the Control4 system using a wireless ZigBee connection through its built-in antenna. Use the Wireless Outlet Switch to control electrical devices such as pumps, Christmas lights, fans, and fluorescent lights, individually or within a lighting scene. The Wireless Outlet Switch can sense the power state of the devices attached to it (On, Off, or Stand-by). WARNING! The Wireless Outlet Switch is rated for a combined load of 1150 Watts; do not plug in devices that require more than 1150 Watts, either alone or in combination. The Control4 Wireless Outlet Switch offers these features: • Power sensors allow the Control4 system to detect the power state of the devices you have plugged into each outlet. • Two tri-color LEDs to indicate outlet activity and system feedback. • A security screw tab that attaches to the outlet’s center screw. • An external button for manual operation and to automatically identify the device to the Control4 system. Specifications Important Warnings and Information WARNING! Improper use or installation can cause SERIOUS INJURY, DEATH, or LOSS/DAMAGE OF PROPERTY. WARNING! Install in accordance with all national, state, and local electrical codes. WARNING! This product generates heat. The room must have adequate ventilation or the ability to dissipate heat effectively. WARNING! This product must be grounded in accordance with the National Electrical Code (NEC) requirements. WARNING! Use only in dry locations. CAUTION! For residential use only. IMPORTANT! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is not liable for any damage incurred because of the misuse of this product. See “Limited 1 Year Warranty” on page 2. Install and Configure a Wireless Outlet Switch To enable full use of the Control4 system’s features, configure your Wireless Outlet Switch to read the power state of the devices that you plug into it. For example, if your switch can read the power state of the DVD player, your DVD player can then participate in concert with the lights and the other devices in your home theater in a lighting scene. 1 Choose a location where the ZigBee wireless communication will be most efficient: (1) Place the Outlet Switch near enough to the next ZigBee device to facilitate communication (2); Keep the Outlet Switch from being continually too close to devices that can cause interference, such as microwave ovens or cordless telephones with a 2.4 GHz frequency. 2 Remove the screw that holds the faceplate onto the AC outlet to which you will plug the Wireless Outlet Switch. 3 Plug the Wireless Outlet Switch into the receptacle of the outlet, keeping the faceplate between the Wireless Outlet Switch and the wall. 4 Through the Wireless Outlet Switch’s security screw tab, insert the screw that you removed in Step 2 and then screw it back in place. 5 Within Composer software, add the outlet to the project and make necessary connections. See “Configure an Outlet Switch or Dimmer” in Composer online help. To identify the Wireless Outlet Switch as part of the Composer software configuration, press the button on the top panel of the Wireless Outlet Switch. 6 Plug in the device you would like to control, such as a DVD player, into one of the Wireless Outlet Switch’s receptacles (on the bottom panel). 7 Push and hold the button on the top panel of the Wireless Outlet Switch until the two LED lights flash orange, On and Off, from one to the next. 8 When the LED lights up on the side that corresponds to the outlet in which your device is plugged, release the button. For example, if the device you have plugged in is on the right side of the Wireless Outlet Switch, release the button when the LED lights on the right side. The LED on that side of the switch alone flashes orange, indicating that it is in the first phase of learning the state (Off) of the device. When it has completed this learning phase, the LED then shines solid orange. 9 When the LED shines solid orange, turn On the device that you have plugged into the Wireless Outlet Switch. The LED light again flashes orange while the Wireless Outlet Switch completes the first phase of Power Requirements: 120 VAC, 50/60 Hz, 1.7 W Load Ratings: (Total of Both Outlets) 120 VAC, 1150 VA, Inductive, Total 120 VAC, 1/3 HP (7.2 FLA), Total 120 VAC, 7.2 A, Ballast, Total Operating Temperature: All load ratings are based on an ambient temperature of 25 degrees Celsius.

Wireless Outlet Switch Installation Guide Supported Models and Requirements LOZ-5S1-W Wireless Outlet Switch Specifications and Supported Fixtures This Control4® Wireless Outlet Switch plugs into a standard, earth-grounded (3-prong) electrical wall outlet and communicates with the Control4 system using a wireless ZigBee (802.15.4) connection through its built-in antenna. Use the Wireless Outlet Switch to control a wide variety of electrical devices. The Wireless Outlet Switch can also sense the power state of the devices attached to it (On or Off). The Control4 Wireless Outlet Switch has two (2) outlets. You can configure these outlets independently for different uses, including: • Controlling a plugged-in audio/video (A/V) component (such as a DVD player or VCR) or other electrical equipment controlled by IR. • Controlling power to a plugged-in relay device (such as a pump) or other household appliances. • Switching a plugged-in florescent lamp On or Off. The Wireless Outlet Switch features include: • Two (2) individually controllable 120 VAC electrical outlets. • Two (2) multi-color LEDs to indi- cate outlet activity and system feedback. • An external button for initial set up of the Wireless Outlet Switch, including identifying the device on the Control4 system and for Power Learning for power sensing. Specifications Important Warnings and Information WARNING! The Wireless Outlet Switch is rated for a combined load as listed in the table above. Do not plug in devices that exceed these ratings, either alone or in combination. Avertissement ! Le commutateur sans fil de sortie est évalué pour une charge combinée comme énuméré dans la table ci-dessus ; ne branchez pas les dispositifs qui excèdent ces estimations, seul ou en association. WARNING! Improper use or installation can cause SERIOUS INJURY, DEATH, or LOSS/DAMAGE OF PROPERTY. Avertissement ! L'utilisation ou l'installation inexacte peut causer des DOMMAGES, la MORT, ou LOSS/DAMAGE SÉRIEUSE DE PROPRIÉTÉ. WARNING! Install in accordance with all national, state, and local electrical codes. Avertissement ! Installez selon tous les national, état, et codes électriques locaux. WARNING! This product generates heat. The room must have adequate ventilation or the ability to dissipate heat effectively. Avertissement ! Ce produit produit de la chaleur. La salle doit avoir à ventilation proportionnée ou la capacité d'absorber la chaleur efficacement. WARNING! This product must be grounded in accordance with the National Electrical Code (NEC) requirements. Avertissement ! Ce produit doit être fondu selon les conditions électriques nationales de code (NEC). WARNING! Use this product only in dry locations. Avertissement ! Employez ce produit seulement dans des endroits secs. CAUTION! This product is for residential use only. Attention ! Ce produit est pour à l'usage résidentiel ou commercial seulement. IMPORTANT! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is not liable for any damage incurred because of the misuse of this product. See “Limited 2 Year Warranty” on page 2. Important ! Employer ce produit en quelque sorte autre que décrit dans ce document vide votre garantie. De plus, Control4 n'est pas responsable d'aucun dommage encouru en raison de l'abus de ce produit. Voyez que « Limited 2 Year Warranty » à la page 2. Install and Configure a Wireless Outlet Switch The Wireless Outlet Switch provides a way for a standard AC-powered device to be controlled as a custom Control4 device. The following steps guide you through the Wireless Outlet Switch setup. To complete the configuration, you must have access to the Composer project and the installed Control4 Controller. To install and configure a Wireless Outlet Switch: 1 Choose a location where the ZigBee wireless communication will be most efficient: (1) place closely enough to receive a strong signal, and (2) the switch should not be placed too close to devices that cause interference, such as a 2.4 GHz portable phone. 2 Plug the Wireless Outlet Switch into a power outlet. 3 Plug one (1) or two (2) devices into an outlet provided on the Wireless Outlet Switch. 4 In the Composer software, add and configure the Wireless Outlet switch and the device(s) you plugged into the Wireless Outlet Switch. Specify for each outlet how you intend to use the outlet, such as for control of A/V equipment, for power sensing, or for power control of relay devices. For detailed instructions, refer to the Composer Help topic “Configure a Wireless Outlet Switch.” 5 If you are using the Wireless Outlet Switch for power-sensing (such as to control an AV component), you need to perform Power Learning. See the next section, “Perform Power Learning” for instructions. Perform Power Learning To enable use of the power-sensing features, configure your Wireless Outlet Switch to read the power state of the devices that you plug into it. 1 Follow the steps to “Install and Configure a Wireless Outlet Switch”. 2 Turn Off the device plugged into the Wireless Outlet Switch. 3 Push and hold the button on the top panel of the Wireless Outlet Switch until the two (2) LEDs toggle Orange On/Off, alternating back and forth. 4 Choose an outlet to configure (Outlet 1 or 2) by releasing the button when the LED that corresponds to that outlet number lights up. For example, if a device is plugged into Outlet 1, then release the button when LED 1 lights up. Upon doing so, the LED you chose flashes orange, indicating that the Wireless Outlet Switch is learning a steady state of the device (such as On or Off). When the LED turns solid orange, the Wireless Outlet Switch has learned the steady state, but has not yet determined whether the state is On or Off. Power Requirements: 120 VAC, 50/60 Hz, 1.7 W Minimum Wattage 5 W Load Types and Ratings: (Total of Both Outlets) 120 VAC, 1000 VA, Inductive, Total 120 VAC, 1/3 HP (7.2 FLA), Total 120 VAC, 7.2 A, Ballast, Total Operating Temperature: All load ratings are based on an ambient temperature of 25 degrees Celsius. LEDs Button