Control4 C4-DIN-8ESW-E Manuals

™ The 8-Port Ethernet Switch specifications include: Power 110V-277VAc, 50/60 Hz Operating Temperature 32˚F to 104˚F (0˚C to 40˚C) Power Consumption 2W Communications 10/100 Ethernet Connectors Three (3) Screw Terminals (Line, Neutral, Ground), one (1) 26AWG to 12AWG (.12 - 4mm2) per ter- minal Eight (8) RJ-45 Ethernet Humidity 5% - 95% Non-condensing Storage -4˚ F - 158˚ F (-20˚ C - 70˚ C) Dimensions (HxWxD) 8.5” x 4.3” x 2.3” (215 mm x 109 mm x 57 mm) DIN Module Width 12M Weight 2.3 lbs. (1.04 kg) Shipping Weight 2.8 lbs. (1.27 kg) Front View Figure 1. Front View 1 Power LED 2 Link/Activity LEDs 3 Reset button 4 Ethernet RJ-45 Connectors 5 Line Voltage Connector Pre-Installation Instructions Before You Install in a Control4 Panel 1 Use Composer Pro to add the 8-Port Ethernet Switch to a project, define its location in a panel, and print the panel report. See the Composer Pro User Guide for details. 2 Install the panel following the instructions in the 5-Slot and 2-Slot Panel Installation Guide. 3 Install and wire the Terminal Block for the 8-Port Ethernet Switch following the instructions in the Terminal Block Installation Guide and in the location defined by the Composer Pro panel reports. Before You Install in a Third-Party DIN Rail Panel 1 Install the third-party panel according to the third-party instructions. Supported Model đŏ C4-DIN-8ESW-E 8-Port Ethernet Switch (DIN Rail) Introduction The Control4® 8-Port Ethernet Switch is part of the Control4 Panelized Lighting System. It installs in the Control4 5-Slot or 2-Slot Panel or in any standard DIN rail panel with 35mm rails. The Ethernet Switch is a standard 8-port 10/100 switch that allows a single Ethernet CAT5e cable to be pulled into the panel, and then distributed to up to seven (7) other Control4 panelized lighting devices in the panel. Box Contents đŏ 8-Port Ethernet Switch đŏ Warranty Card đŏ ĉġ+.0ŏ0$!.*!0ŏ3%0$ŏ */0((0%+*ŏ1% ! (this document) đŏ 8-Port Ethernet Switch Wiring Guide Warnings and Considerations WARNING! Improper use or installation can cause SERIOUS INJURY, DEATH or LOSS/DAMAGE OF PROPERTY. ATTENTION! Une mauvaise utilisation ou installation peut entraîner des blessures graves, décès ou perte / dommages à la propriété. WARNING! This device must be protected by a circuit breaker (20A max). ATTENTION! Cet appareil doit étre protègè par un disjoncteur (20A max.) WARNING! Ensure that all circuit breakers feeding into the panel are OFF before installing or servicing the devices. ATTENTION! Assurez-vous que tous les disjoncteurs d’alimentation dans le panneau sont éteints avant d’installer ou de réparer l’appareil. IMPORTANT! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See “Troubleshooting.” IMPORTANT! Changes or modifications not expressly approved by Control4 could void the user’s authority to operate the equipment. IMPORTANT! The Ethernet Switch should be installed by a licensed electrician in accordance with all national and local electrical codes. Requirements and Specifications Prior to installing this product, ensure that the Control4 5-Slot or 2-Slot Panel or that the cabinet to house the switch has been installed. 8-Port Ethernet Switch Installation Guide 1 2 4 3 5