Core HR10 Manuals

Configuring the Remote After charging the remote fully, proceed with the setup by following these steps: 1) Remove endcap and slide the power switch right to the “off” position. 2) Plug in the provided Micro-USB cable to the remote USB port located on the left side behind the endcap (see figure one for location). 3) Plug the other end of the USB cable into a computer or chassis with compatible software already installed and running. 4) Slide the power switch left to the “on” position. 5) Enter the password requested on the HR30 screen using the numeric buttons on the remote. Enter: 3526 then press Enter. The screen should now say “USB Active”. 6) You are now ready to proceed with configuration. Please refer to the HR10 integration note or your System Training Guide for more details. Removal and Replacement of the battery 1) To access the battery, locate the Endcap Release Button on the bottom of the remote. While depressing the Endcap release button, pull the Endcap away from the body of the remote as illustrated. 2) Remove the two screws holding the Battery Retaining Bracket in place using a #1 Phillips Screwdriver. Slide out the old battery. 3) CAUTION: Danger of explosion if battery is incorrectly replaced. Replace battery with only Core Brands approved battery part number 2900008. (Contact your local dealer for replacement battery.) 4) Assure proper orientation while inserting replacement battery. Battery label should be faced down and gold plated charging contacts should enter the unit first. Refer to the illustration below. Improper installation of the battery will result in permanent damage to the remote. HR10 Quick Reference Guide English © 2017 Core Brands, LLC. P/N 10018770 (Rev-B3) 11/2017 3 4 on rear on rear Remove Battery Retaining Bracket and slide out old battery Endcap Release Button Correct Battery orientation Incorrect Battery orientation Gold plated contacts Remove Screws Pull Endcap out while pressing Endcap Release Button Endcap Micro-USB Micro-USB Micro-USB 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9. Only use attachments/accessories specified by the manufacturer. 10. Unplug this apparatus during Iightning storms or when unused for long periods of time. 11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. FCC and IC Information: This Class B digital apparatus complies with Part 15 of the FCC rules and with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions: 1. This device may not cause interference and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Contains: FCC ID: 2ADHKATWINC1500 IC ID: 20266-WINC1500PB CAN ICES-3B / NMB-3B Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC and IC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the exemption from the routine evaluation limits in section 2.5 of RSS 102. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. Warning: The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102, and users can obtain Canadian information on RF exposure and compliance from the Canadian Representative Product Solutions Group at Tel: (519) 763-4538. Important Safety Instructions