Crestron DM-MD6X1 Manuals

1 quickstart guide DM-MD6X1 www.crestron.com 888.273.7876 201.767.3400 ©2010 Specifications subject to change without notice. For details, refer to the latest revision of the DM-MD6X1 DigitalMedia™ Switcher Operations Guide, Doc. 6850. QUICKSTART DOC. 6851B (2024731) 06.10 DigitalMedia™ Switcher All brand names, product names, and trademarks are the property of their respective owners. DM-MD6X1 1 Before Starting 2 3 ! CAUTION: Do not connect power cords until instructed to do so. NOTE: Before beginning any of these QuickStart procedures, make certain that all DigitalMedia™ cables are installed throughout the home. Connect DigitalMedia Room Controllers and Repeaters A. Using a DigitalMedia™ cable (DM-CBL-P or DM-CBL-NP), connect the switcher output directly to a DM-RMC-100 Room Controller, or, if required, first connect to a DM-DR Repeater and then connect the output of the DM-DR to a DM-RMC-100. The illustration immediately to the right shows the special connectors used for the three cables contained within the DigitalMedia cable. The illustration at the far right shows a typical wiring configuration for the switcher’s single DM output port. (The output can support a maximum of up to three repeaters and one room controller.) B. For detailed instructions on operation and setup of the DM-DR Repeater and the DM-RMC-100 Room Controller, refer to the latest version of their respective Operations & Installation Guides (Doc. 6745 and Doc. 6743). DM-CBL-P or DM-CBL-NP DM-DR Repeater Room Controller DM-CBL-P or DM-CBL-NP ‘D’ Video ‘M’ Data Management ‘DMNet’ Control & Power ‘D’ Video ‘DMNet’ Control & Power ‘M’ Data Management (CAT5E) Connect DigitalMedia Device Power Source 24 VDC + G A. The switcher can supply up to 30 watts of internal power to connected room controllers repeaters and transmitters up to their rated level. B. Ensure that the EIG jumpers are installed and wired between E and I for internal power to be routed to the connected devices. If power is not being supplied to an external device, make sure the jumper is not connected. C. If the devices to be connected (both input and output) will require more power than is available from the switcher, connect them to an external 24 VDC supply (that can supply the required power) by connecting the E and G terminals of the EIG connector to the + and G terminals of the (unpowered) external supply. (Refer to the illustration.) EXTERNAL POWER SUPPLY INTERNAL POWER 4 Connect Other Inputs and Outputs : : DM Input D M 24ABG RGB IN 2: From Analog and Component Video Input Sources NOTE: Before beginning any of these QuickStart procedures, make certain that all DigitalMedia™ cables are installed throughout the home. NOTE: Before beginning any of these QuickStart procedures, make certain that all DigitalMedia™ cables are installed throughout the home. NOTE: Before beginning any of these QuickStart procedures, make certain that all DigitalMedia™ cables are installed throughout the home. NOTE: If a DM switcher, or other DM device supplying power, is connected to a DM IN 4-6 port of the DM-MD6X1, then the +24V wire between the DM device and the DM-MD6X1 must be disconnected. The A B G wires must remain connected. VIDEO IN 1: From YPbPr, Composite or S-video Sources HDMI IN 3: HDMI Digital Video/Audio DM IN / 24 A B G (4-6): From Outputs of DM Transmitters or Other DM Devices USB HID: To USB HID Device LAN: 10BASE-T/ 100BASE-TX Ethernet to LAN HDMI OUT: HDMI Digital Video/Audio Output AUDIO OUT: Balanced Line Level Audio SPDIF IN 1: From Digital Audio Output AUDIO IN (1-2): Balanced Line Level Analog Audio