Crestron FlipTop FT2 Series Manuals

FT2-202-ELEC-PTL FlipTop™FT2 Series Cable Management System, 202 Size, Electrical, Pass-Through Lid DocType - 9082A (2058223) 07.21 Getting Started Scan the QR code to view the Quick Start Guide. www.crestron.com/docs/9083 For information on the Crestron® FT2-202-ELEC-PTL, visit www.crestron.com/model/6511666. Certification and Compliance Regulatory Models: FT2-202-ELEC-AL, FT2-202-ELEC-B As of the date of manufacture, the product has been tested and found to comply with specifications for CE marking. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  l Reorient or relocate the receiving antenna.  l Increase the separation between the equipment and receiver.  l Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  l Consult the dealer or an experienced radio/TV technician for help. Industry Canada (IC) Compliance Statement CAN ICES-3 (B)/NMB-3(B) Legal The product warranty can be found at www.crestron.com/warranty. The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents. Certain Crestron products contain open source software. For specific information, visit www.crestron.com/opensource.

Quick Start The Crestron® FT2-700-MECH FlipTop™ cable management system device, for simplicity within this document called the FlipTop assembly, installs into a table or other horizontal surface to provide modular tabletop connectivity for users. The one-touch lid on the unit conceals 12 module spaces arranged in two rows of six. The FlipTop assembly includes eight pass-through cable modules and four blank plate modules. Each pass-through cable module accommodates a Crestron FT2A-CBL-PT Series Pass-Through Cable (not included) and various other third-party interface cables. Use blank plate modules to cover any unused module spaces within the FlipTop assembly. The flexible modular design of the FlipTop assembly can be customized with an assortment of Crestron accessories (not included): • FT2A-CBL-PT is a series of pass-through cables optimized for the provided pass-through cable modules. • FT2A-CBLR-GR is a series of gravity cable retractors. Each cable in the retractor pulls out up to 3 ft (0.9 m) and retracts gently back into the FlipTop assembly. • FT2A-PLT-KEY-10 is a pack of 10 keystone plate modules. Each module accommodates standard flush-mount keystone connectors. • FT2A-CHGR-USBA-BASIC is a USB rapid charging module that provides two USB Type-A charging ports. • FT2A-PWR-US is a series of AC power outlet modules that provide one or more NEMA 5 type receptacles above the table. The basic model provides one additional outlet below the table; the other models provide two. • FT2A-UTK-SHELF is an under-table utility shelf capable of holding HDMI® switches or HDBaseT® transmitters. • FT2A-PLT-BLANK-10 is a pack of 10 blank plate modules used to supplement those provided with the FlipTop assembly. Each module covers one unused module space within the assembly. • FT2A-PLT-PT-10 is a pack of 10 pass-through cable modules used to supplement those provided with the FlipTop assembly. Each module accommodates a Crestron FT2A-CBL-PT Series Pass- Through Cable or a third-party interface cable. NOTE: For more information about FlipTop assembly accessories, refer to the specific product manual located at www.crestron.com/manuals. Check the Box Item Qty FT2-700-MECH 1 Bars, Locking, with Screws (P/N 4528906) 3 Module, Blank Plate (P/N 2049602) 4 Module, Pass-Through Cable (P/N 4526880) 8 Spacer, Plastic, FT2-700 (P/N 2050568) 4 Template, Cutout (P/N 4527491) 1 FT2-700-MECH-AL Only Bezel, FT2-700, Alloy (P/N 4529321) 1 FT2-700-MECH-B Only Bezel, FT2-700, Black (P/N 4529320) 1 Mount the FlipTop Assembly Mount the FlipTop assembly into an existing FT-600 FlipTop assembly installation or create a new mounting. The next three sections describe the mounting procedure. If replacing an the FT-600 FlipTop assembly, there is no need to cut a new mounting hole (skip “Cut the Mounting Hole”). If this is not a replacement, cut a hole and secure the FlipTop assembly (skip “Replace FT-600 FlipTop Assembly”). Cut the Mounting Hole NOTE: Before cutting the mounting hole, check underneath the table for any obstructions that may impede the installation of the FlipTop assembly, retractors, and accessories. 1. Trace an outline of the mounting hole onto the table using the included cutout template. 2. Cut a mounting hole in the table with an appropriate saw. Replace FT-600 FlipTop Assembly To replace an older FT-600 FlipTop assembly with an FT2-700 FlipTop assembly: 1. Remove the FT-600 FlipTop assembly by loosening four socket screws that secure two mounting plates and the FlipTop assembly to the surface. 2. Attach four plastic spacers (included) to each corner of the FT2-700 FlipTop assembly prior to inserting into the mounting hole previously cut for the FT-600 FlipTop assembly. Location of Plastic Spacers on FlipTop Assembly Corners (Enlarged View) Flat portion must face upward. Plastic spacer (4) FT2-700 FlipTop assembly (top front) Clip a plastic spacer into two slots on each corner of FlipTop assembly. Secure the FlipTop Assembly To secure the FlipTop assembly: 1. Ensure that all four swiveling dogs are positioned inside of the FlipTop assembly, and then insert the assembly into the mounting hole until the top lip is flush with the table surface. CAUTION: Set the screwdriver torque to its lowest setting to avoid stripping the swiveling dogs and damaging the table. If removing the FlipTop assembly from the table, ensure that the screwdriver rotation is set correctly before loosening the swiveling dogs. 2. Carefully tighten the four swiveling dogs in each corner of the FlipTop assembly clockwise until the assembly is secured in place against the table. Do not overtighten the swiveling dogs. Location of Swiveling Dogs Swiveling dogs (4) Retractable lid FlipTop assembly Install the Modules NOTE: Installation procedures for most modules are available in separate product documentation. For more information, refer to the specific product manual located at www.crestron.com/manuals. The following section provides best practices and includes installation procedures for pass-through cable modules and blank plate modules. Position the Modules NOTE: The FlipTop assembly includes eight FT2A-PLT-PT pass-through cable modules and four FT2A-PLT-BLANK blank plate modules. No other modules are included. Follow the best practices below when performing module installation: • Perform module installation in the following order: 1. AC Power Outlet Modules (FT2A-PWR-US) 2. Retractor modules (FT2A-CBLR-GR) 3. All other modules (FT2A-PLT-KEY, FT2A-PLT-PT, and FT2A-PLT-BLANK) • Place the FT2A-CBLR-GR modules only at the ends of a module row. • Dress all cables after installing each module. NOTE: FT2A-CBLR-GR modules are compatible with electrical and mechanical FlipTop assemblies; however, the LED indicators on the front of these modules do not light when installed into an FT2-700-MECH. Install the Pass-Through Cable Module Each pass-through cable module is packaged with one nylon grommet and one cable plate. One empty module slot is required for installation. To assemble and install the pass-through cable modules into the FlipTop assembly: 1. Separate the grommet. 2. Insert the cable into the grommet with the connector facing up toward the end user. NOTE: The grommet is optional. It fits 10mm or smaller cables (non-4K cables such as USB, CAT6, VGA, and audio). Omit the grommet if installing larger cables (such as Crestron 4K video cables) into the module. 3. Press the grommet back together to secure the cable inside. 4. Push the grommet and cable into the hole in the cable plate. 5. Insert the cable plate into one of the three slots in the pass-through module. The top of the cable connector should sit flush with the top of the module. NOTE: If the cable connector extends past the top of the pass-through module, the FlipTop assembly lid cannot close. Location of Cable Plates within the Pass-Through Cable Module The cable plate with the nylon grommet may be installed in one of these three slots. Pass-through module (with side plate removed) 6. Attach the side plate to the module by snapping the plastic clips on the plate into the two slots on the module. NOTE: Ensure that the cable moves freely in the module prior to attaching the side plate, as the plate is difficult to remove once it is attached. If the side plate must be removed, use a small, flat object (such as a flat-head screwdriver) to carefully pry the plastic clips on the side plate off of the module near the two slots. Location of Plastic Clips on Side Panel Snap to attach (or pry to remove) the plastic clips from the slots on a pass-through module. 7. Feed the other end of the cable through an empty module slot in the FlipTop assembly. 8. Slide the pass-through cable module into the empty module slot in the FlipTop assembly. Use the guide ribs on the front and rear of each module to help position the module in the assembly. Install the Blank and Keystone Plate Module Two blank plate modules are included to fill empty slots in the module rows. A keystone plate module allows for cables terminated with standard keystone jacks to be installed in the FlipTop assembly. The blank and keystone plate modules each require one empty module slot for installation. Blank and Keystone Plate Modules Blank plate module Keystone plate module To install a blank or keystone plate module into the FlipTop assembly: • Slide the blank plate module down into the appropriate module slot. Use the guide ribs on the front and rear of each module to help position it in the assembly. • For the keystone plate module, complete the following. 1. Snap the cable’s keystone jack into the keystone opening in the keystone plate module. 2. Feed the cable down through the empty module slot. FT2-700-MECH FlipTop™ Cable Management System FT2 Series, 700 Size, Mechanical

Quick Start The Crestron® FT2-1400-ELEC FlipTop™ cable management system device, for simplicity within this document called the FlipTop assembly, installs into a table or other horizontal surface to provide modular tabletop connectivity for users on either side of the table. The two one-touch lids on the unit conceal 18 module spaces arranged in two rows of nine. The FlipTop assembly includes 12 pass-through cable modules and six blank plate modules. Each pass-through cable module accommodates a Crestron FT2A-CBL-PT Series Pass-Through Cable (not included) and various other third-party interface cables. Use blank plate modules to cover any unused module spaces within the FlipTop assembly. An included power pack, power supply holder, power cord, and DC power splitter energize the two power buses located within the FlipTop assembly. A second power pack with power supply holder (not included) is required if two Crestron FT2A-CHGR-USBA/C USB Rapid Charging Modules (not included) are installed in a single FlipTop assembly. The flexible modular design of the FlipTop assembly can be customized with an assortment of Crestron accessories (not included): • FT2A-CBL-PT is a series of pass-through cables optimized for the provided pass-through cable modules. • FT2A-CBLR-GR is a series of gravity cable retractors. Each cable in the retractor pulls out up to 3 feet (0.9 m) and retracts gently back into the FlipTop assembly. • FT2A-CBLR-1T is a series of one-touch cable retractors. Each cable in the retractor pulls out up to 5 feet (1.5 m) and retracts when the cable retractor button is pressed or a Crestron control system automatically retracts the cable. • FT2A-CP is a series of active connector plate modules. Each module provides panel mounted connectors, which allow the connection of devices using separate, detached interface cables (not included). • FT2A-CHGR-USBA/C is a USB rapid charging module. It provides one USB Type-C™ charging port and one USB Type-A charging port. • FT2A-PWR-US is a series of AC power outlet modules that provide one or more NEMA 5 type receptacles above the table. The basic model provides one additional outlet below the table; the other models provide two. • FT2A-UTK-SHELF in an under-table utility shelf capable of holding HDMI® switches or HDBaseT® transmitters. • FT2A-UTK-PWS is a power supply for the FlipTop assembly. A maximum of two power supplies may be connected to a single FlipTop assembly. • FT2A-PLT-BLANK-10 is a pack of 10 blank plate modules used to supplement those provided with the FlipTop assembly. Each module covers one unused module space within the assembly. • FT2A-PLT-PT-10 is a pack of 10 pass-through cable modules used to supplement those provided with the FlipTop assembly. Each module accommodates a Crestron FT2A-CBL-PT Series Pass- Through Cable or a third-party interface cable. NOTE: For more information about FlipTop assembly accessories, refer to the specific product manual located at www.crestron.com/manuals. Check the Box Item Qty FT2-1400-ELEC 1 Bars, Locking, with Screws (P/N 4527589) 4 Cable, DC Power Splitter,  Single 2.1 mm to Dual 2.1 mm (P/N 2050094) 1 Connector, 3-Pin (P/N 2003575) 2 Holder, Power Supply (P/N 2048887) 1 Module, Blank Plate (P/N 2049602) 6 Module, Pass-Through Cable (P/N 4526880) 12 Power Cord, 5 ft 10 in. (1.78 m) (P/N 2042043) 1 Power Pack, 24 Vdc, 2.5 A, 100-240 Vac (P/N 2045873) 1 Template, Cutout (P/N 4527605) 1 Tie Wrap (P/N 2047935) 2 FT2-1400-ELEC-AL Only Bezel, FT2-1400, Alloy (P/N 4527431) 1 FT2-1400-ELEC-B Only Bezel, FT2-1400, Black (P/N 4527430) 1 Mount the FlipTop Assembly The next two sections describe the mounting procedure. Cut the Mounting Hole NOTE: Before cutting the mounting hole, check underneath the table for any obstructions that may impede the installation of the FlipTop assembly, retractors, and accessories. 1. Trace an outline of the mounting hole onto the table using the included cutout template. 2. Cut a mounting hole in the table with an appropriate saw. Secure the FlipTop Assembly To secure the FlipTop assembly: 1. If using a single power supply, connect the dual connector ends of the included DC power splitter cable to the two barrel jacks in the bottom of the power bus so the cable may be accessed later. For location of the barrel jacks, refer to “Connect the FlipTop Assembly.” DC Power Splitter Cable (Included) 2. Ensure that all four swiveling dogs are positioned inside of the FlipTop assembly, and then insert the assembly into the mounting hole until the top lip is flush with the table surface. CAUTION: Set the screwdriver torque to its lowest setting to avoid stripping the swiveling dogs and damaging the table. If removing the FlipTop assembly from the table, ensure that the screwdriver rotation is set correctly before loosening the swiveling dogs. 3. Carefully tighten the four swiveling dogs in each corner of the FlipTop assembly clockwise until the assembly is secured in place against the table. Do not overtighten the swiveling dogs. Location of Swiveling Dogs Swiveling dogs (4) Retractable lids (2) FlipTop assembly Connect the FlipTop Assembly Access the two network connectors and two power bus barrel jacks on the underside of the FlipTop assembly. Location of 3-Pin Network Connector and Power Bus Barrel Jacks Power bus barrel jack FlipTop assembly (bottom view) Power bus barrel jack 3-Pin network connector NOTE: Second network connector is not visible in the above diagram. Connect the Network A network connection between the FlipTop assembly and a Crestron control system or DMPS3 enables remote control of installed accessories. For example, when a networked FlipTop assembly with a one-touch cable retractor is installed in a room with an occupancy sensor and the sensor detects an unoccupied room, the FlipTop assembly communicates with the system to automatically retract the cable. Connect the FlipTop assembly to a Crestron control system or DMPS3 via the 3-pin connectors using standard Cresnet® cable. The red power lead is not connected and should be terminated. 3-Pin Connector with Wires Attached White (Y) Blue (Z) Black (G) Connect and Place the Power Supply The FlipTop assembly ships with one 24 Vdc power supply that is used to supply power to the power bus in the assembly. There are six possible locations to attach the power supply. Connect the power supply prior to installing any modules. NOTE: Two power supplies are required if installing two FT2A-CHGR-USBA/C modules in the FlipTop assembly. For more information, refer to the FT2A-CHGR-USBA/C Installation Guide (Doc. 8219) at www.crestron.com/manuals. To connect the power supply to the power bus: 1. Underneath the table, connect the power supply to the bottom of the power bus: • If connecting one power supply, connect the power supply’s power cord to the single connector end of the DC power splitter cable. Refer to step 1 in “Secure the FlipTop Assembly.” • If connecting two power supplies, connect each power supply’s power cord to a barrel jack in the power bus. 2. Use two tie wraps (included) and dress the power cord. 3. Slide the power supply into the power supply holder until it is secured in place. 4. Insert the power supply holder into the side of the FlipTop assembly so that the four mounting posts on the rear of the holder engage the four rectangular slots in one of the six mounting locations. Location of Power Supply FlipTop assembly Power supply Power supply holder Rectangular slots (4) 5. Slide the holder downward until it is secured to the FlipTop assembly. FT2-1400-ELEC FlipTop™ Cable Management System FT2 Series, 1400 Size, Electrical

The Crestron® FT2-202-ELEC-PTL FlipTop™cable management system installs into a table or other horizontal surface to provide modular connectivity. It features a retracting lid that disappears within the enclosure. When the lid is retracted, six module slots are arranged in one row. The flexible modular design may also be customized with an assortment of Crestron accessories, and the pass-through lid style allows cables to be fully extended while the lid is closed. For more information about the accessories, please visit www.crestron.com/Crestron-FlipTops. To configure your FlipTop, launch the FlipTop Configuration Tool. In the Box 1 FT2-202-ELEC-PTL Additional Items 2 Locking Bars with screws and gaskets (4532479) 1 Cable, DC Power Splitter (2050094) 1 Connector, Plug (2003575) 1 Holder, Power Supply (2048887) 1 Power Cord, 5 ft 10 in. (1.78 m) (2042043) 1 Power Pack, 24VDC, 2.5 A, 100-240VAC (2045873) 1 Cutout Template (4529443) FT2-202-ELEC-PTL Quick Start FlipTop™FT2 Series Cable Management System, 202 Size, Electrical, Pass-Through Lid 1

The Crestron® FT2-1200-ELEC-PTL FlipTop™cable management system installs into a table or other horizontal surface to provide modular connectivity. It features a retracting lid that disappears within the enclosure. When the lid is retracted, nine module slots are arranged in one row. The flexible modular design may also be customized with an assortment of Crestron accessories, and the pass-through lid style allows cables to be fully extended while the lid is closed. For more information about the accessories, please visit www.crestron.com/Crestron-FlipTops. To configure your FlipTop, launch the FlipTop Configuration Tool. In the Box 1 FT2-1200-ELEC-PTL Additional Items 2 Locking Bars with screws and gaskets (4532619) 1 Cable, DC Power Splitter (2050094) 1 Connector, Plug (2003575) 1 Holder, Power Supply (2048887) 1 Power Cord, 5 ft 10 in. (1.78 m) (2042043) 1 Power Pack, 24VDC, 2.5 A, 100-240VAC (2045873) 1 Cutout Template (4528347) FT2-1200-ELEC-PTL Quick Start FlipTop™FT2 Series Cable Management System, 1200 Size, Electrical, Pass-Through Lid 1

The Crestron® FT2-500-ELEC-PTL FlipTop™cable management system installs into a table or other horizontal surface to provide modular connectivity. It features a retracting lid that disappears within the enclosure. When the lid is retracted, eight module slots are arranged in two rows of four. The flexible modular design may also be customized with an assortment of Crestron accessories, and the pass-through lid style allows cables to be fully extended while the lid is closed. For more information about the accessories, please visit www.crestron.com/Crestron-FlipTops. To configure your FlipTop, launch the FlipTop Configuration Tool. In the Box 1 FT2-500-ELEC-PTL Additional Items 3 Locking Bars with screws and gaskets (4532634) 1 Cable, DC Power Splitter (2050094) 1 Connector, Plug (2003575) 1 Holder, Power Supply (2048887) 1 Power Cord, 5 ft 10 in. (1.78 m) (2042043) 1 Power Pack, 24VDC, 2.5 A, 100-240VAC (2045873) 1 Cutout Template (4528039) FT2-500-ELEC-PTL Quick Start FlipTop™FT2 Series Cable Management System, 500 Size, Electrical, Pass-Through Lid 1

The Crestron® FT2-700-ELEC and the FT2-700-ELEC-PTL FlipTop™ cable management systems install into a table or other horizontal surface to provide modular tabletop connectivity for users. The FT2-700-ELEC series feature a one touch lid that retracts fully and disappears with the tap of a button. When the lid is retracted, 12 module slots are arranged in two rows of six. The flexible modular design may also be customized with an assortment of Crestron accessories. For more information about the accessories, please visit www.crestron.com/Crestron-FlipTops. The FT2-700-ELEC Series features a built in electrical power bus, which enables compatibility with one-touch cable retractors, active connector plates, and USB rapid charging modules. It also enables backlighting of the symbol icons on all retractors, connector plates, and USB charging modules. The FT2-700-ELEC-PTL offers an alternative pass-through lid style which allows cables to be fully extended while the lid is closed. The FT2-700-ELEC and the FT2-700-ELEC-PTL are functionally similar. For simplicity within this document, they are both referred to as the "FT2-700 assembly." In the Box 1 FT2-700-ELEC, FlipTop™ FT2 Series, 700 Size, Electrical Additional Items 3 Bars, Locking, with Screws (P/N 4528906) 1 Cable, DC Power Splitter (P/N 2050094) 1 Holder, Power Supply (P/N 2048887) 4 Module, Blank Plate (P/N 2049602) 8 Module, Pass-Through Cable (P/N 4526880) 1 Power Cord, 5 ft 10 in. (1.78 m) (P/N 2042043) 1 Power Pack, 24 VDC, 2.5 A, 100-240 VAC (P/N 2045873) 4 Spacer, Plastic, FT2-700 (P/N 2050568) 1 Template, Cutout (P/N 4527491) FT2-700-ELEC-AL Only 1 Bezel, FT2-700, Alloy (P/N 4529321) FT2-700-ELEC-PTL-AL Only 1 Bezel, FT2-700, Pass-Through Lid, Alloy (P/N 4531563) FT2-700-ELEC-PTL-B Only 1 Bezel, FT2-700, Pass-Through Lid, Black (P/N 4531562) FT2-700-ELEC-B Only 1 Bezel, FT2-700, Black (P/N 4529320) 1 FT2-700-ELEC Series Quick Start FlipTop™ FT2 Series, 700 Size, Electrical