CyberPower CPS1000EI Manuals

CPS1000EI/CPS2000EI User’s Manual K01-C000003-00 IMPORTANT SAFETY INFORMATION (SAVE THESE INSTRUCTIONS) This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate the INVERTER. Insure the wall outlet and INVERTER are located near the equipment being attached for proper accessibility. To reduce risk of damage and injury, please use batteries with good quality. Provide adequate ventilation for the battery compartment. The battery enclosure should be designed to prevent accumulation and concentration of hydrogen gas at the top of the compartment. DO NOT expose the INVERTER to rain, snow or liquids of any type. The INVERTER is designed for indoor use only. DO NOT obstruct the ventilation openings. CAUTION! Risk of electric shock, do not remove cover. No user serviceable parts inside. The battery can energize hazardous live parts inside even when the AC input power is disconnected. To avoid electrical shock, turn off the INVERTER and unplug it from the AC power source before servicing the battery. Servicing the battery can only be performed by trained personnel. INSTALLING YOUR INVERTER SYSTEM UNPACKING Inspect the unit upon receipt. The box should contain the following: Inverter Unit
1; Power Cord
1; User Manual
1 HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT 1. Insure that the equipment plugged into the AC outlet does not exceed the INVERTER unit’s rated capacity (1000VA/600W for CPS1000EI; 2000VA/1200W for CPS2000EI). If rated unit capacities are exceeded, an overload condition may occur and cause the INVERTER unit to shut down or the circuit breaker trip. 2. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert Watts (W) or Amps (A) into VA by doing the calculations below. Note: The below equation only calculates the maximum amount of VA that the equipment can use, not what is typically used by the equipment at any one time. Users should expect usage requirements to be approximately 60% of below value. TO ESTIMATE POWER REQUIREMENTS 1. 220 V x Amps (A) = VA 2. Add the totals up for all pieces of equipment and multiply this total by 0.6 to calculate actual requirements. There are many factors that can affect the amount of power that your computer system will require. The total load that you will be placing on the battery-powered outlets should not exceed 80% of the unit’s capacity. HARDWARE INSTALLATION GUIDE Before installation, please read and understand the following instructions: 1. Placement The Inverter must be installed in a protected environment away from heat- emitting appliances such as a radiator or heat register. Do not install this product where excessive moisture is present. 2. Ventilation The location should provide adequate air flow around the INVERTER with one inch minimum clearance on all sides for proper ventilation. 3. Connect the Battery Connect the external battery with the DC cables from the back of the INVERTER. Follow battery polarity guide located near battery cables as below. “+” Red cable for battery positive polarity; “-” Black cable for battery negative polarity. 4. Connect to AC and Charge the Battery Connect the INVERTER to a wall outlet. Avoid using extension cords and adapter plugs. Charging the battery for at least 8 hours is recommended to insure that the battery is fully charged. To recharge the battery, simply leave the unit plugged into a wall outlet. To maintain optimal battery charge, leave the INVERTER plugged into an AC outlet at all times. This INVERTER can be charged even when INVERTER is not turned on. 5. Connect the Load Connect the equipment to the INVERTER outlet. Please make sure that the total loads of your equipments are less than the maximum total power load of the INVERTER. BASIC OPERATION FRONT PANEL DESCRIPTION 1. Fault LED The red LED will light when fault or over load occurs. 2. Battery Mode LED The yellow LED will light when power mains are abnormal and the unit will work in battery mode. 3. AC Mode LED The green LED will light when utility power is normal. 4. Power Switch Press the power switch to turn the INVERTER ON or OFF. . REAR PANEL DESCRIPTION 1. DC Input Cable (Black) Connect to battery negative polarity. 2. DC Input Cable (Red) Connect to battery positive polarity. 3. Input Circuit Breaker The circuit breaker provides optimal overload protection. 4. Charger Control The charger control function should only be operated by trained professionals. If it is operated incorrectly, the battery will be damaged. Contact your local technical support for setting details. 5. Input Voltage Range Selector Input voltage range is defined in specification section. Output voltage is the same as input voltage in AC mode. A. Select “Narrow” setting for general electrical appliance such as TUBE LIGHT, ENERGY

CPS1000EI/CPS2000EI User’s Manual K01-C000003-00 IMPORTANT SAFETY INFORMATION (SAVE THESE INSTRUCTIONS) This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate the INVERTER. Insure the wall outlet and INVERTER are located near the equipment being attached for proper accessibility. To reduce risk of damage and injury, please use batteries with good quality. Provide adequate ventilation for the battery compartment. The battery enclosure should be designed to prevent accumulation and concentration of hydrogen gas at the top of the compartment. DO NOT expose the INVERTER to rain, snow or liquids of any type. The INVERTER is designed for indoor use only. DO NOT obstruct the ventilation openings. CAUTION! Risk of electric shock, do not remove cover. No user serviceable parts inside. The battery can energize hazardous live parts inside even when the AC input power is disconnected. To avoid electrical shock, turn off the INVERTER and unplug it from the AC power source before servicing the battery. Servicing the battery can only be performed by trained personnel. INSTALLING YOUR INVERTER SYSTEM UNPACKING Inspect the unit upon receipt. The box should contain the following: Inverter Unit�1; Power Cord�1; User Manual�1 HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT 1. Insure that the equipment plugged into the AC outlet does not exceed the INVERTER unit’s rated capacity (1000VA/600W for CPS1000EI; 2000VA/1200W for CPS2000EI). If rated unit capacities are exceeded, an overload condition may occur and cause the INVERTER unit to shut down or the circuit breaker trip. 2. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert Watts (W) or Amps (A) into VA by doing the calculations below. Note: The below equation only calculates the maximum amount of VA that the equipment can use, not what is typically used by the equipment at any one time. Users should expect usage requirements to be approximately 60% of below value. TO ESTIMATE POWER REQUIREMENTS 1. 220 V x Amps (A) = VA 2. Add the totals up for all pieces of equipment and multiply this total by 0.6 to calculate actual requirements. There are many factors that can affect the amount of power that your computer system will require. The total load that you will be placing on the battery-powered outlets should not exceed 80% of the unit’s capacity. HARDWARE INSTALLATION GUIDE Before installation, please read and understand the following instructions: 1. Placement The Inverter must be installed in a protected environment away from heat- emitting appliances such as a radiator or heat register. Do not install this product where excessive moisture is present. 2. Ventilation The location should provide adequate air flow around the INVERTER with one inch minimum clearance on all sides for proper ventilation. 3. Connect the Battery Connect the external battery with the DC cables from the back of the INVERTER. Follow battery polarity guide located near battery cables as below. “+” Red cable for battery positive polarity; “-” Black cable for battery negative polarity. 4. Connect to AC and Charge the Battery Connect the INVERTER to a wall outlet. Avoid using extension cords and adapter plugs. Charging the battery for at least 8 hours is recommended to insure that the battery is fully charged. To recharge the battery, simply leave the unit plugged into a wall outlet. To maintain optimal battery charge, leave the INVERTER plugged into an AC outlet at all times. This INVERTER can be charged even when INVERTER is not turned on. 5. Connect the Load Connect the equipment to the INVERTER outlet. Please make sure that the total loads of your equipments are less than the maximum total power load of the INVERTER. BASIC OPERATION FRONT PANEL DESCRIPTION 1. Fault LED The red LED will light when fault or over load occurs. 2. Battery Mode LED The yellow LED will light when power mains are abnormal and the unit will work in battery mode. 3. AC Mode LED The green LED will light when utility power is normal. 4. Power Switch Press the power switch to turn the INVERTER ON or OFF. . REAR PANEL DESCRIPTION 1. DC Input Cable (Black) Connect to battery negative polarity. 2. DC Input Cable (Red) Connect to battery positive polarity. 3. Input Circuit Breaker The circuit breaker provides optimal overload protection. 4. Charger Control The charger control function should only be operated by trained professionals. If it is operated incorrectly, the battery will be damaged. Contact your local technical support for setting details. 5. Input Voltage Range Selector Input voltage range is defined in specification section. Output voltage is the same as input voltage in AC mode. A. Select “Narrow” setting for general electrical appliance such as TUBE LIGHT, ENERGY

EN CPS1000EI/CPS2000EI User’s Manual K01-C000028-02 IMPORTANT SAFETY INFORMATION (SAVE THESE INSTRUCTIONS) This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate the INVERTER. Insure the wall outlet and INVERTER are located near the equipment being attached for proper accessibility. CAUTION! To reduce risk of damage and injury, please use batteries with good quality. CAUTION! Provide adequate ventilation for the battery compartment. The battery enclosure should be designed to prevent accumulation and concentration of hydrogen gas at the top of the compartment. DO NOT expose the INVERTER to rain, snow or liquids of any type. The INVERTER is designed for indoor use only. DO NOT obstruct the ventilation openings. DO NOT connect neutral of the power distribution box on the wall to: (a) The OUTPUT neutral of inverter. or (b) The INPUT neutral of equipment. Otherwise the reversed polarity will damage the inverter and the connected equipment. CAUTION! The battery can energize hazardous live parts inside even when the AC input power is disconnected. CAUTION! To avoid electrical shock, turn off the INVERTER and unplug it from the AC power source before servicing the battery. Servicing the battery can only be performed by trained personnel. CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area, free of conductive contaminants. (Please see specifications for acceptable temperature and humidity range.) CAUTION! To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before installing equipment. CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not use with or near aquariums. Condensation from the aquarium can come in contact with metal electrical contacts and cause the machine to short out. INSTALLING YOUR INVERTER SYSTEM UNPACKING Inspect the unit upon receipt. The box should contain the following: Inverter Unit1; Power Cord1; User Manual1 OVERVIEW The CPS1000EI/CPS2000EI ensures home/office users the always-on power supply with the exceptional power performance comes at a comfortable pricing. Featuring the high-efficiency conversion design, the Power Inverter supplies long-lasting and reliable power to various appliances and provide longer backup for equipments. The defensive mechanisms of automatic switch-over and overload protection ensure the efficiency of appliances as protection against overload and load shredding is secured. HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT 1. Ensure that the equipment plugged into the AC outlet does not exceed the INVERTER unit’s rated capacity (1000VA/600W for CPS1000EI; 2000VA/1200W for CPS2000EI). If rated unit capacities are exceeded, an overload condition may occur and cause the INVERTER unit to shut down or the circuit breaker trip. 2. There are many factors that can affect the amount of power that your appliances will require. For optimal system performance keep the load below 80% of the unit’s rated capacity. HARDWARE INSTALLATION GUIDE Before installation, please read and understand the following instructions: 1. Placement The Inverter must be installed in a protected environment away from heat- emitting appliances such as a radiator or heat register. Do not install this product where excessive moisture is present. 2. Ventilation The location should provide adequate air flow around the INVERTER with 10 CM minimum clearance on all sides for proper ventilation. 3. Connect the Battery Connect the external battery with the DC cables from the back of the INVERTER. Follow battery polarity guide located near battery cables as below. “+” Red cable for battery positive polarity; “-” Black cable for battery negative polarity. 4. Connect to AC and Charge the Battery Connect the INVERTER to a wall outlet. Avoid using extension cords and adapter plugs. Charging the battery for at least 8 hours is recommended to insure that the battery is fully charged. To recharge the battery, simply leave the unit plugged into a wall outlet. To maintain optimal battery charge, leave the INVERTER plugged into an AC outlet at all times. This INVERTER can be charged even when INVERTER is not turned on. 5. Connect the Load Connect the equipment to the INVERTER outlet. Please make sure that the total loads of your equipments are less than the maximum total power load of the INVERTER. BASIC OPERATION FRONT PANEL DESCRIPTION 1. Fault LED The red LED will light when fault or over load occurs. 2. Battery Mode LED The yellow LED will light when power mains are abnormal and the unit will work in battery mode. 3. AC Mode LED The green LED will light when utility power is normal. 4. Power Switch Press the power switch to turn the INVERTER ON or OFF. . REAR PANEL DESCRIPTION *6 outlet types available including: Universal, Schuko, French, UK, India and NEMA, type. 1. DC Input Cable (Black) Connect to battery negative polarity.