Danfoss TP5000 si range Manuals

TP5000 Si Range Installation and User Instructions Electronic 5/2 day programmable room thermostat Mains, Battery and RF versions GB ® Certification Mark


 
 

 
 

      

          

         

          

      !"# $    %&# '  

$  ( )$&   * %&     +,    


,    (* - !" .   
$ $ &/ ( )0   * )0 ,    


$   1 2  '!!345+6 $    (   ,*
     (* &&" ,  77  4  
,    8 --  59&""    :  ;
!" 58      '#     / :9 " 2 


             

$       >    >  > ?


   >     !"#
>     > %&# + '  


>  + ( 1 @ )$&* %&    $   A>


> 2    (* - !" . $   
$ $ &/ ( )0   * $    1 +0


0>2   1   '!!345+6
> >   (  2   *
      (* &&"  77  4 > -     8 --  59&"" /B  ;
!" $ >  8 '# 9  1 / :9 "      <#
  
   

                               !"      #$%      &  %           
 
'    %     %(    ) ( )  (  )  !*  #$  + ,  -( ) ( # #.#)    TP5000 Honeywell T6360B Honeywell T4360E Sunvic TLX Models Invensys (ACL Drayton) RTS models COM CALL SAT B A C 4 - 2* 3 1 3 2* 1 1 1 3 3 * selected models only  
    
   

TP5000 + RF Installation Instructions User Instructions Instructions d’installation Instructions d’utilisateur Installationsanweisungen Inbetriebnahme-Instruktion Instrucciones de instalación Instrucciones del usuario Instruktions vejledning Brugervejleding Electronic 5/2 day programmable room thermostat Installatie handleiding Instructiesevoor Gebruik Ïäçãßåò åãêáôÜóôáóçò Ïäçãßåò ÷ñÞóçò Instrukcja instalacji Instrukcja Użytkownika Montavimo instrukcijos Informacija Vartotojui Istruzioni per l’uso Istruzioni per l’utente GB F D ES DK NL GR P LT I ® Certification Mark

Fig.1 TP5000 Si/TP5000 RF Si User Instructions Mon-Fri Sat-Sun Fig.2 Before programming the thermostat press and release the RESET button to restart the unit. (Fig. 1) Setting the Clock and Day The day and time are set in the factory and therefore it will not normally be necessary to do this on site. Changes between summer and winter time are handled automatically by the unit. Accepting the Factory Pre-settings The TP5000 Si has pre-set times already programmed in, which often suit most people (see table below). Note: If set up for 4 events per day, events 3 & 4 are skipped. If set up for 2 events per day, events 2, 3, 4 & 5 are skipped and the events are re-numbered. To adjust the factory pre-settings & set your own time and temperature programmes For Days 1-5 (weekdays) a) Press PROG (Fig. 2) until the 1st pre-set time and temperature (Event 1 Days 1,2,3,4,5) (Fig. 3). b) Use + or – buttons (Fig. 4) to adjust the TIME (press and hold to change in 10 min increments). c) Use Λ or V buttons (Fig. 5) to adjust the TEMPERATURE. d) Press PROG (Fig. 2) to move to next preset time & temp (Event 2) (Fig. 6). e) Repeat steps b, c & d for programming Events 3, 4, 5 & 6. For Days 6-7 (weekends) Press • PROG (Fig. 2) to show 1st pre-set time and temperature (Event 1 Days 6-7) (Fig. 7). Repeat steps b, c and d above to programme time and temperature events for • the weekend. Returning to RUN mode Press PROG (Fig. 2) – the colon in the LCD display will start to flash (Fig. 8). Fig.5 Fig.4 Fig.6 Fig.7 Fig.8 Event Time Temp. °C 1 06:30 20 2 08:30 15 3 11:30 20 4 13:30 15 5 16:30 21 6 22:30 15 Event Time Temp. °C 1 07:30 20 2 09:30 20 3 11:30 20 4 13:30 20 5 16:30 20 6 22:30 15 RESET Fig.3 Complete Shut off - Summer time Press Λ and V together to enter thermostat mode. A frost protection symbol (snowflake in a shield) will appear in the display . Press the down arrow ∨ once, OFF will appear in the display. To return to automatic programming press both ∧ and ∨ together.