Danfoss VLT FC Series Manuals

Items Supplied • VLT® Wireless Communication Panel LCP 103. • Gasket Illustration 1.1 VLT® Wireless Communication Panel LCP 103 Compatible Drive Series NOTICE Compatible drives have a white USB port. • VLT® HVAC Drive FC 102 • VLT® Refrigeration Drive FC 103 • VLT® AQUA Drive FC 202 • VLT® AutomationDrive FC 301/FC 302 • VLT® Lift Drive LD 302 Compatible software versions - FC 102: 5.10 - FC 103: 2.10 - FC 202: 3.10 - FC 30x: 8.03 Approvals and Certifications FCC ID: 2ANSELCP-103 NOTICE FCC COMPLIANCE NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by 1 or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected. • Consult the dealer or an experienced radio/ television technician for help. Modifications: Any modifications made to this device that are not approved by Danfoss may void the authority granted to the user by the FCC to operate this equipment. RF EXPOSURE COMPLIANCE This portable transmitter with its antenna has shown compliance with FCC’s SAR limits for general population/ uncontrolled exposure. The maximum listed SAR level is 0.22 W/kg (body). The antenna used for this device must not be co-located or operating in conjunction with any other antenna or transmitter. Installation Instructions VLT® Wireless Communication Panel LCP 103 VLT® FC Series FC 102, FC 103, FC 202, FC 301/FC 302, and LD 302 Danfoss A/S © 08/2018 All rights reserved. MI38V402

These installation instructions contain the following sections: • fuse/relay locations for specified A, B, C frame frequency converters • voltage ratings • fuse replacement table 1.1 Fuse/Relay Locations for A Frame The following illustrations show the input power, motor, and relay locations for A2, A3, and A5 frame sizes. The A5 illustration also contains the location of the drive fuses. NOTICE Note that these locations are different than what is indicated in the Operating Instructions. Illustration 1.1 Frames A2 and A3 1 Input power 2 Relays 3 Motor Table 1.1 Legend to Illustration 1.1 Illustration 1.2 Frame A5 1 Drive fuses 2 Input power 3 Motor 4 Relays Table 1.2 Legend to Illustration 1.2 1.2 Fuse/Relay Locations for B and C Frames The following illustrations show the input power, motor, and relay locations for B1, B2, C1, and C2 frame sizes. NOTICE Note that these locations are different than what is indicated in the Operating Instructions. Installation Instructions VLT® FC Series Internal Fuse Replacement MI92D102 - VLT® is a registered Danfoss trademark

Installation Guide Control Card VLT® FC Series 1 Introduction 1.1 Compatible Drives This guide describes the replacement of the control card in: • VLT® HVAC Drive FC 102. • VLT® Refrigeration Drive FC 103. • VLT® AQUA Drive FC 202. • VLT® AutomationDrive FC 301/FC 302. • VLT® Lift Drive LD 302. 1.2 Safety Instructions Only Danfoss authorized, qualified personnel is allowed to repair this equipment. WARNING DISCHARGE TIME The drive contains DC-link capacitors, which can remain charged even when the drive is not powered. High voltage can be present even when the warning indicator lights are off. Failure to wait the specified time after power has been removed before performing service or repair work could result in death or serious injury. - Stop the motor. - Disconnect AC mains, permanent magnet type motors, and remote DC-link supplies, including battery back-ups, UPS, and DC-link connections to other drives. - Wait for the capacitors to discharge fully. The minimum waiting time is specified in table Discharge time and is also visible on the nameplate on top of the drive. - Before performing any service or repair work, use an appropriate voltage measuring device to make sure that the capacitors are fully discharged. Table 1: Discharge Time, VLT® HVAC Drive FC 102 Voltage [V] Minimum waiting time (minutes) 4 7 15 20 30 40 200–240 1.1–3.7 kW (1.50–5 hp) – 5.5–45 kW (7.5–60 hp) – – – 380–480 1.1–7.5 kW (1.50–10 hp) – 11–90 kW (15–121 hp) – – 315–1000 kW (450–1350 hp) AN279051429263en-000101 / 130R0788 | 1 Danfoss A/S © 2018.09

Installation Guide VLT® Wireless Communication Panel LCP 103 VLT® FC Series FC 102, FC 103, FC 202, FC 301/FC 302, and LD 302 1 Introduction 1.1 Items Supplied • VLT® Wireless Communication Panel LCP 103 • Gasket e30bg047.10 Illustration 1: VLT® Wireless Communication Panel LCP 103 1.2 Compatible Drive Series NOTICE Compatible drives have a white USB port. • VLT® HVAC Drive FC 102 • VLT® Refrigeration Drive FC 103 • VLT® AQUA Drive FC 202 • VLT® AutomationDrive FC 301/FC 302 • VLT® Lift Drive LD 302 AN331428064824en-000101 / 130R0814 | 1 Danfoss A/S © 2020.02

MAKING MODERN LIVING POSSIBLE Instruction VLT® FC Series Add On Instruction for MCA 121 EtherNet/IP

MAKING MODERN LIVING POSSIBLE Operating Instructions VLT® FC Series Option Panel

Operating Guide Safe Torque Off VLT® Frequency Converters vlt-drives.danfoss.com

ENGINEERING TOMORROW Service Guide VLT® FC Series, D1h–D8h, Da2/Db2/Da4/Db4, E1h–E4h, J8/J9 VLT® HVAC Drive FC 102 • VLT® Refrigeration Drive FC 103 • VLT® AQUA Drive FC 202 VLT® AutomationDrive FC 302 • VLT® AutomationDrive FC 361 • VLT® Parallel Drive Modules vlt-drives.danfoss.com