Dell 1900 Manuals

w w w. d e l l . c o m | s u p p o r t . d e l l . c o m Dell™ PowerEdge™ 1900 Systems Getting Started With Your System Guide de mise en route Primeiros passos com o sistema Procedimientos iniciales con el sistema

w w w. d e l l . c o m | s u p p o r t . d e l l . c o m Dell™ PowerEdge™ 1900 Systems Getting Started With Your System 系统使用入门 開始使用系統 はじめに 시스템시작하기

w w w. d e l l . c o m | s u p p o r t . d e l l . c o m Dell™ PowerEdge™ 1900 Systems Hardware Owner’s Manual

About Cautions CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. Microprocessor Installation Information CAUTION: Any installation that requires removal of the system cover is intended solely to be performed by trained service technicians. See your Product Information Guide for complete information about safety precautions, working inside the computer and protecting against electrostatic discharge. NOTICE: If the front of your system chassis is labeled with a "II," your system is upgradeable to the Quad-Core Intel® Xeon® Processor 5300 series. See www.dell.com and support.dell.com for information on processor availability and upgrade options for your system. Prior to adding or replacing a processor, you must verify that the latest system BIOS and BMC firmware versions are on your system. Loading the latest BIOS and BMC firmware versions will ensure that the processor is fully supported. NOTICE: Failure to update your system to the latest BIOS and BMC firmware versions prior to installing the microprocessor can result in your system hanging during POST. 1 Check your system BIOS version in the System Setup program. See "Using the System Setup Program" in the Hardware Owner’s Manual included on the CDs provided with your system or on support.dell.com. 2 Check the latest system BIOS version available on support.dell.com. 3 Download and flash the latest BIOS version if necessary. 4 Check your system BMC firmware version in the BMC Configuration Utility. To enter the BMC Configuration Utility, press when prompted during POST. For more information, see the BMC User’s Guide included on the CDs provided with your system or on support.dell.com. 5 Check the latest system BMC firmware version available on support.dell.com. 6 Download and flash the latest BMC firmware, if necessary. 7 Install the processor. See "Installing System Components" in the Hardware Owner’s Manual included on the CDs provided with your system or on support.dell.com. ____________________ Information in this document is subject to change without notice. © 2006–2007 Dell Inc. All rights reserved. Printed in the U.S.A. Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; Intel and Xeon are registered trademarks of Intel Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own. March 2007

Dell™ PowerEdge™ 19x0 and 29x0 Systems Installing a SATA Optical Drive

About Cautions CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. Installing the Stabilizer Feet and/or the Optional Casters on Your System This document provides instructions for installing the stabilizer feet and/or the optional casters on your system. To prepare your system, perform the following steps: 1 Disconnect the system and any attached peripherals from their electrical outlets, and then disconnect the peripherals from the system. CAUTION: The system may weigh up to 45 kilograms (100 pounds) when fully loaded. To prevent personal injury, do not attempt to move the system by yourself. 2 Place the system on a flat work surface with the bottom of the system overhanging the surface edge. Installing the Stabilizer Feet NOTE: If you plan to install the optional casters, you must install the casters on the stabilizer feet before installing the feet on your system. See "Installing the Optional Casters" for instructions. To install the stabilizer foot on the system, align the foot tabs with the chassis cutouts on the bottom of the system, and slide the tabs into the cutouts until the tabs lock into place in the foot tab slots. See Figure 1. Repeat to install the remaining foot. Installing the Optional Casters NOTE: For an existing configuration, you must remove the stabilizer feet from the system before installing the casters. See "Removing the Stabilizer Feet" for instructions. 1 Slide the caster plate under the caster retaining tabs on the stabilizer foot until the caster locking tab locks into place behind the caster. See Figure 1. Repeat to install the remaining three casters, installing two casters per foot. 2 Install the stabilizer feet on your system. See "Installing the Stabilizer Feet." Removing the Stabilizer Feet To remove the stabilizer foot from the system, locate the foot tabs, which are locked in the foot tab slots. Press down and hold both tabs, and then slide the foot away from the slots until the tabs are free from the chassis. See Figure 1. Repeat to remove the remaining foot. February 2006

w w w. d e l l . c o m | s u p p o r t . d e l l . c o m Dell™ PowerEdge™ 1900 Systems Hardware Owner’s Manual book.book Page 1 Tuesday, September 1, 2009 4:19 PM

Trusted Platform Module (TPM) Update Systems that are shipping in China are not equipped with TPM. Disregard any TPM options listed in the "Using the System Setup Program" chapter of your Hardware Owner’s Manual. ____________________ Information in this document is subject to change without notice. © 2007 Dell Inc. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own. November 2007

w w w. d e l l . c o m | s u p p o r t . d e l l . c o m Dell™ PowerEdge™ 1900 Systems Information Update