Dialogic DM/IP601-CPCI-100BT Manuals

Dialogic® DM/IP601-CPCI-100BT IP Board Quick Install Card Part number 64-0027-02 Copyright © 2002-2007 Dialogic Corporation. All Rights Reserved. Before You Begin Protecting the Board from Damage CAUTION: All computer boards are sensitive to electrostatic discharge (“ESD”). Handle all static-sensitive boards and components at a static-safe work area, and observe anti-static precautions at all times. If you are not familiar with ESD safety precautions, visit http://www.dialogic.com/support/hwinstall to learn more. Unpacking the Board Unpack the Dialogic® DM/IP601-CPCI-100BT board (“board”) according to the following steps: 1. Prepare a static-safeguarded work area. 2. Carefully remove the board from the shipping carton and anti-static packaging. Handle the board by the edges and avoid touching the board’s components. 3. Lay the board on the static-dissipative work surface. Note: Place boards in static-shielding bags when carrying boards from station to station. CAUTION: Do not remove the board from the anti-static packaging until you are ready to install it. Observe proper anti-static precautions at all times. Installing the Hardware NOTE: In a Windows environment, install the software first, the hardware second, and then run the Dialogic® Configuration Manager (DCM) to configure the system. 1. Turn the power to the chassis OFF if you do not have a live insertion system. If you do have live insertion capability, the power to the chassis can remain ON. 2. Remove the chassis cover plate or open the front door. 3. Select an empty expansion bus slot. NOTE: When power is on, the Rear I/O module should be installed first, before the main board. 4. Install the Rear I/O module in the rear of the slot selected in step 3. Use the slot’s board guides as you insert the board into the chassis slot. Make sure that the tabs on the board extractors engage the guide holes in the chassis card cage, then lock down the board extractors until the red locking tabs snap shut. CAUTION cPCI backplane pins are bent easily. Make sure that the board is seated with hand pressure before fully seating board. If board extractors are used to seat the board, make sure to seat evenly. 5. Install the board in the front of the slot selected in step 3. Use the slot’s board guides as you insert the board into the chassis slot. Make sure that the tabs on the board extractors engage the guide holes in the chassis card cage, then lock down the board extractors until the red locking tabs snap shut. NOTE: If the power to the chassis is on, power is automatically applied to the board, the Out of Service LED lights briefly and then goes out, and the Power LED goes on. 6. Tighten the retaining screws to secure the board firmly in the chassis slot (optional). 7. Select a new slot and repeat steps 4-6 for each board you Physical Description RED YEL CARR SGNL LOOP RED YEL CARR SGNL LOOP A L A R M S T A T U S RED YEL CARR SGNL LOOP RED YEL CARR SGNL LOOP A L A R M S S A T U S P5 P4 P1 Board Extractor POWER Alarm Status LEDs OUT OF SERVICE Board Extractor Baseboard Daughterboard 1 2 3 4 / P 5 P2 P 2 P 5 J1-J4 R J-48C Jacks B N C C onnectors E thernet Interface C onnector E thernet Interface C onnector Trunk 1 Trunk 1 Trunk 2 Trunk 3 Trunk 4 Faceplate Compact PCI Board T-1 and E-1 120-Ohm E-1 75-Ohm (front view) Rear I/O Module Rear I/O Module Compact PCI Baseboard Rear I/O Modules Part: Power LED Red Alarm LEDs Yellow Alarm LEDs Carrier Signal LEDs Loopback LEDs Out of Service LED Function: Indicates board is powered up. Not functional in this assembly. Not functional in this assembly. Not functional in this assembly. Not functional in this assembly. Indicates board is out of service or in reset from host. Part: J1–J4 P2 P5 BNC Connectors Function: Not functional in this assembly. Telephony network interface test port Rear I/O module connector to Compact PCI backplane Not functional in this assembly P1, P4, P5 Compact PCI board connectors to backplane. Ethernet Connector Connection to Ethernet network NOTES: Rear I/O Modules are ordered separately and are available in two different forms depending on the type of connectors used, guided or unguided. Select a Rear I/O Module that is compatible with your chassis type. See the PICMG 2.0 D3.0 Compact PCI Specification for more information on guided and unguided connectors.