Digi PortServer TS Series Manuals

Quick Start Guide PortServer® TS Family Welcome to your Digi product Get started: This guide helps you with initial product setup. Need more? Find additional supporting material for this product at www.digi.com/support/portserverts. Or connect to the online documentation by scanning this code: Digi Technical Support: Digi offers multiple support plans to help you get the most out of your product. For information on Technical Support plans and pricing, contact us at 877.912.3444 or visit www.digi.com/support. Documentation feedback: To provide feedback on this documentation, send your comments to [email protected]. 1 Verify your components Included equipment Required equipment Note A loose label sticker that includes the unique device password is included in the box. Retain this label sticker with your hardware records. This default password will be needed if the device is factory reset and you want to access the web UI on the device. 2 Confirm serial pinouts Step 1: Configure DIP switches (MEI models only) For PortServer TS 1-4 port models, if the connected device is not EIA-232, set the DIP switches as shown for the serial port according to your serial device requirements. PortServer TS 1-4 port DIP Switch settings: PortServer TS P MEI DIP switch settings: Switch settings Up/On Down/Off For PortServer TS P MEI series only, in EIA-232 mode, if switch 3 is down, 9V power is provided on pin 9 (DTR). If switch 3 is up, power on pin 9 is disabled and 5V power can be enabled on pin 1 (RI) through the software interface. If using EIA-422 or EIA-485, the DIP switch settings are the same as for any other PortServer TS 1-4 MEI model. If switch 4 is up, the termination resistor is connected. If switch 4 is down, the termination resistor is not connected. Step 2: Review serial pinouts Pin positions for connecting serial devices Note For additional information on Digi part numbers for serial cables and adapters, refer to the Cable Adapter Insert Card. Pin # on 10-wire connector Pin # on 8 wire connector EIA-232 MEI versions only EIA-422/485 Full- Duplex EIA-485 Half-Duplex 1 RI TxD- N/A 2 1 DSR* RxD- DATA- 3 2 RTS RTS+ N/A 4 3 CGND CGND CGND 5 4 TxD TxD+ N/A 6 5 RxD RxD+ DATA+ 7 6 SGND SGND SGND 8 7 CTS CTS+ N/A 9 8 DTR RTS- N/A 10 DCD* CTS- N/A *Use the Altpin setting to swap these two signals. Note The CTS and RTS control signals are available as separate differential signals in the EIA- 422/EIA-485 4-wire mode. Do not use these differential signals in 2-wire mode. The CTS and RTS differential signals are not terminated or biased internally. Any termination or biasing must be done externally. Serial port pin assignments © 2019 Digi International Inc. Digi, Digi International, and the Digi logo are trademarks or registered trademarks in the United States and other countries worldwide. All other trademarks mentioned in this document are the property of their respective owners.

PortServer TS Family Series Quick Start Guide *If switch 4 is up, termination resistor is connected. If switch 4 is down, termination resistor is not connected. Set serial DIP switch (MEI versions only) according to your serial device requirements. Pinout information available on back of quick start. Congratulations! Configuration is complete. Go to the User's Guide on the CD for more information. Connect serial device Connect Ethernet cable Connect power supply Insert CD Follow wizard © Digi International Inc., 2006. Digi, Digi International, the Digi logo, and PortServer TS are trademarks or registered trademarks of Digi International, Inc. in the United States and other countries worldwide. All other trademarks are the property of their respective owners. Software & Documentation Software & Documentation PortServer TS 1 MEI (shown) PortServer TS 16 MEI (shown) Connect Ethernet cable Connect power cord and flip power switch on If you have a UNIX system and it does not use an auto-mounter, you will need to manually mount the CD. See the back of this guide for UNIX specific instructions. Connect serial devices Connect Ethernet cable Connect power supply PortServer TS MEI PortServer TS P MEI PortServer TS H MEI PortServer TS What you will need PortServer TS 8 PortServer TS 16 MEI Ethernet cable not included The PortServer TS 8/16 MEI settings are configured through the software. Complete the Quick Start Guide and go to the User's Guide for the procedure to configure the MEI ports. The ports are set to EIA-232 by default. If your device is not EIA-232, configure the MEI settings immediately after completing the Quick Start. The default settings will not harm your device, however, we recommend configuring the MEI settings immediately as a precaution. *If you need help with cabling, see other side Connect serial devices 1 2 3 1 2 3 1 2 4 RUN WIZARD INSTALL 8 or 16 Port INSTALL 1, 2, or 4 Port 3 Be sure to check Digi Support for the latest firmware updates at: http://support.digi.com 1 2 3 4 * In EIA-232 mode, If switch 3 is down, 9V power is provided on pin 9 (DTR). If switch 3 is up, power on pin 9 is disabled and 5V power can be enabled on pin 1 (RI) through the software interface. Note for PortServer TS P MEI series only - Power (green) on; power supply LEDs will flash during startup Power - steady blinking; seeking or waiting for an IP address Link - on; physical network detected 10/100 - off; 10Mbit Ethernet detected, on; 100Mbit Ethernet detected ACT - on; bad initialization, off; ready, blinking; network activity COL - on; Ethernet collision detected LEDs will flash during startup Up/On Down/Off EIA-232 EIA-422/485 Full-Duplex EIA-485 Half-Duplex Switch Settings * 1 2 3 4 * Status (yellow) blinking; seeking or waiting for an IP address - for status codes, see User's Guide You must disable firewall/antivirus software before running wizard. ! Power cord (PortServer TS 16 families only) Wall and brick power supply (PortServer TS families 1/2/4/8 only) DB-9 -RJ-45 adapter PN:(1P) B 90000687-88