Digital Watchdog Spot DW-HDSPOTMOD16 Manuals

WHAT’S IN THE BOX Quick setup and download guides 1 set 12V DC power cable 1 USB mouse 1 Quick Start Guide Quick Start Guide STEP 1 – SETTING UP THE SPOT MONITORING MODULE OFF-SITE STEP 2 – POWERING UP THE SPOT MONITORING MODULE SAFETY TIPS 1. Connect the module to an appropriate power supply. 2. Connect the module to a local monitor off-site for configuration. 3. Make sure the module is connected to the same network as your IP cameras, Universal HD over Coax® VMAX® A1™ DVRs or VMAX IP Plus™ NVR. When the module boots up, it will be in protective mode and the password setup screen will appear. 1. You will be asked to setup a new password. The password must be a minimum of 8 characters with at least 3 combinations of upper-case letters, lower-case letters, numbers, and special characters. 2. When the module boots up for the first time, you will be guided through the startup wizard. 3. You can also access the monitor for basic setup via its web browser. 1. During the boot-up process, the module should not be interrupted by pressing any buttons on the mouse. Do not unplug the power adapter or turn the module off during the boot-up process. 2. A UPS (uninterrupted power supply) is highly recommended to prevent damage to the module during a power outage. The Digital Watchdog Spot™ monitoring module requires only 2 steps to complete the installation—local configuration off-site, and power and monitor connection at the site. NOTE: The Spot monitoring module supports up to 16 supported devices registered, with single, quad and 16-channel view. Tel: +1 (866) 446-3595 / (813) 888-9555 Technical Support Hours: 9:00AM – 8:00PM EST, Monday thru Friday digital-watchdog.com Attention: This document is intended to serve as a quick reference for initial set-up. It is recom- mended that the user read the entire instruction manual for complete and proper installation and usage. DW-HDSPOTMOD DW-HDSPOTMOD16 ORIGINAL LAYOUT VERTICAL LAYOUT ONVIF IP Cameras VMAX AHD CORE and VMAX IP Plus Network DW Spot VGA Output VGA HDMI Output HD ONVIF IP Cameras VMAX® A1™ DVRs (via RTSP) and VMAX® NVRs Network DW Spot™ Monitor VGA Output True HD Output VGA HD POWER SUPPLY NETWORK PORT USB MOUSE VGA HD POWER SUPPLY NETWORK PORT USB MOUSE VGA HD FRONT PANEL BACK PANEL Default login information: admin | no password When logging into the recorder for the first time, you will be prompted to setup a new password. NOTE: Download all your support materials and tools in one place. 1. Go to: http://www.digital-watchdog.com/resources 2. Search your product by entering the part number in the ‘Search by Product’ search bar. Results will populate automatically based on the part number you enter. 3. Click ‘Search’. All supported materials, including manuals and quick start guide (QSGs) will appear in the results.

’ Quick Start Guide Quick Start Guide DW-HDSPOTMOD DW-HDSPOTMOD16 DW-HDSPOTMOD DW-HDSPOTMOD16 Default Login Information Username: admin Password: no password WHAT S IN THE BOX Quick Start Guide 1 Set 12V DC power cable 1 Set USB mouse 1 Set NOTE: Download All Your Support Materials and Tools in One Place 1. Go to: http://www.digital-watchdog.com/support-download/ 2. Search your product by entering the part number in the ‘Search by Product’ search bar. Results for applicable part numbers will populate automatically based on the part number you enter. 3. Click ‘Search’. All supported materials, including manuals, Quick Start Guides (QSG), software and firmware will appear in the results. Attention: This document is intended to serve as a quick reference for initial set-up. It is recommended that the user read the entire instruction manual for complete and proper installation and usage. Tel: +1 (866) 446-3595 / (813) 888-9555 digital-watchdog.com Technical Support Hours: 9:00AM – 8:00PM EST, Monday thru Friday The Digital Watchdog Spot™ monitoring module requires only 2 steps to complete the installation—local configuration off-site, and power and monitor connection at the site. STEP 1 – SETTING UP THE SPOT MONITORING MODULE OFF SITE 1. Connect the module to an appropriate power supply. 2. Connect the module to a local monitor off site for configuration. 3. Make sure the module is connected to the same network as your IP cameras, Universal HD over Coax® VMAX® A1™ DVRs or VMAX IP Plus ™ NVR. DW-HDSPOTMOD DW-HDSPOTMOD16 FRONT PANEL FRONT PANEL BACK PANEL USB DC 12V LAN VGA OUT HD OUT BACK PANEL PWR REC USB DC 12V USB LAN VGA OUT HD OUT NET PWR REC NET POWER SUPPLY POWER SUPPLY NETWORK PORT USB MOUSE NETWORK PORT USB MOUSE VGA VGA HD HD SAFETY TIPS 1. During the boot up process, the module should not be interrupted by pressing any buttons on the mouse. Do not unplug the power adapter or turn the module off during the boot up process. 2. A UPS (uninterrupted power supply) is highly recommended to prevent damage to the module during a power outage. STEP 2 – POWERING UP THE SPOT MONITORING MODULE 1. When the module boots up, it will be in protective mode. This means you will not be able to access the module’s setup menu until you enter the proper username and password. 2. To unlock the module, right-click anywhere on the screen. The login screen will appear. (Default username / password: admin / no password) 3. When the module boots up for the first time, you will be guided through the startup wizard. 4. You can also access the Spot monitor for basic setup via its web browser. ONVIF IP Cameras VMAX® A1™ DVRs and VMAX® IP Plus™ NVRs Network DW Spot VGA Output HDMI Output HD VGA NOTE: The Digital Watchdog spot monitoring module supports up to 16 supported devices registered, with single, quad and 16-channel view. Available from A1 Security Cameras www.a1securitycameras.com email: [email protected]

Before operating the system, please read this user manual and retain it for future reference. The picture might differ according to the specification and model. Copyright © DW. All rights reserved. Specifications and pricing are subject to change without notice. Rev: 07/20 USER MANUAL