Draper FlexShade F MO Series Manuals

Overview - Components CAUTION Read and understand all warnings (Page 2 of this document) before beginning installation. Contents Overview - Components .......................................................................................1 PLEASE READ - Important Safety and Installation Information ....................2 PLEASE READ - Field Adjustments, Cleaning and Maintenance ...................2 Section 1 - Mounting Brackets ...........................................................................3 Section 2 - Idler-End and Operator End Assemblies ......................................3 Section 3 - Pocket Headbox Installation ...........................................................4 Section 4 - Installing Closure Panel ...................................................................5 Section 5 - Mounting / Assembly ..........................................................................................6 Section 6 - Fabric/Roller Assembly Alignment ................................................8 Section 8 - Electrical Connections ............................................................... 9-11 Section 9 - Dimensions ......................................................................................12 Section 10 - Large Hardware Dimensions ......................................................12 FLEXSHADE D*MO Locking Ring SHADE FABRIC SHADE FABRIC Motor Plate Idler End Bracket Spanner Wrench Motor End Bracket Coupler Bracket Assembly } TOOLS REQUIRED POWER DRILL PENCIL TAPE MEASURE HARDWARE (by others) LEVEL Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.7999 © 2021 All Rights Reserved | FORM: Coupled_DR_FS_MO_Large_Hardware_Inst21 Dual Roller Coupled Motorized FlexShades® (Large Hardware) INSTRUCTIONS INSTALLATION & OPERATION If you have any difficulties installing or servicing your Dual Roller Coupled FlexShades®, call your dealer or Draper, Inc. PERSONNEL REQUIRED WARNING Improper installation and use of the Dual Roller Fascia Coupled FlexShade® can result in serious injury or death. Primarily, injuries can occur if the unit falls due to imprecise installation, mishandling of the unit during installation or installation on an insufficient wall or ceiling structure. Please use extreme care. 1. Please read the following installation guidelines thoroughly and follow them carefully. Failure to do so may cause product to fall or otherwise fail, and could result in serious injury. 2. Installation and calibration of the unit should only be performed by an authorized, qualified, and experienced professional. In particular, electrical work and wiring [indicated in diagram by dashed lines] must be completed only by a qualified professional electrician who has read this manual completely and is familiar with the construction and operation of this equipment and the hazards involved. 3. Do not affix the unit to wall or ceilings that have inadequate strength to permanently hold the unit during use. It is the owner’s and installer’s responsibility to confirm the wall or ceiling to which the unit attaches is sufficient to permanently hold the weight and stress loads of the unit at all times. Draper, Inc., is not responsible for improper installation, application, testing, or workmanship related to the product at place of installation. 4. It is the installer’s responsibility to ensure appropriate fasteners are used for mounting. 5. All brackets, fascia, headboxes, pockets, wall clips, and other hardware must be installed level. Unit must be level and square. 6. Never leave the area while operating the unit during installation, maintenance, or normal operation, unless it is secure and safe. 7. Before testing or operation, carefully inspect the entire area and path of the shade and areas underneath the shade to be sure no persons or objects are in the area. 8. Turn off power and any nearby equipment or cables carrying electricity before connecting switches, wires, controls, or electrical components. 9. Ensure the limit switches are pointed down or accessible when placing the motor in brackets/endcaps. 10. All motors should be tested and limits set using test cord before shades are wired. 11. Do not wire motors in parallel without written permission from Draper, Inc. 12. During testing or operation, carefully watch the surrounding area for any potential safety concerns including nearby persons or objects. 13. After installation, the entire system, including all sensors, should be carefully tested to ensure safe and normal operation. Extreme care should be taken during testing to remain clear of moving parts to avoid possible injury. 14. Operation of unit should be performed only by authorized and qualified personnel, who have been trained in the safe and effective operation of the unit and understand its safety features. 15. The safety features of the unit , including sensors, should never be disabled, bypassed, or overridden. The system should not be operated until all safety features, including the sensors, are properly and completely installed, calibrated, and tested. 16. Unit may need to comply with local, state, or district rules and regulations, in particular when installed in schools. All applicable rules and regulations should be reviewed before installation and use. 17. Failure to precisely follow installation guidelines invalidates all warranties. 18. Custom products/installations may not be reflected in this manual. Call Draper, Inc., if you have questions about the installation of custom products or any questions about your installation. Before Beginning Installation 1. Look for any job site conditions that could interfere with installation or operation of the system. 2. Read carefully and be sure to understand all installation instructions and all related operations manuals. These instructions are intended to serve as a guide for the installer and owner. They should be followed closely and combined with the expertise of experienced qualified installers. Draper, Inc., is not responsible for improper installation, application, testing, or workmanship related to the product at place of installation. Please retain all instructions for future use. 3. Open cartons lengthwise. 4. Locate and lay out all pieces. 5. Inspect all boxes to ensure you have received the proper shade and parts. Controls may be shipped separately, or in same carton as shade. 6. If you have any difficulties with installing, servicing, or operating your shade, call your dealer or Draper, Inc., 765-987-7999. Important Safety Information Important Safety Information PLEASE READ - Important Installation Information Caution: 1. Inspect all boxes to ensure you have received the proper shades and parts. Controls may be shipped separately, or in same carton as shades. 2. Open cartons lengthwise. 3. Before mounting shades, verify measurements on label provided with shade, and ensure unit is installed at correct width. 4. Before connecting switches, controls, or electrical, ensure that power is turned OFF. Wiring indicated in diagram by dashed lines must be completed by an electrician. 5. Do not wire motors in parallel without written permission from Draper. 6. All brackets, fascia, pocket headbox, and other hardware must be installed level. Shades must be level and square. 7. Read the following installation guidelines thoroughly and follow them carefully. Failure to do so may cause product to fall or otherwise fail, and invalidates warranty. 8. Installer is responsible for selecting mounting hardware appropriate for site conditions. PLEASE READ - Safety Information PLEASE READ - Field Adjustments Each Draper Solar Control Shade is tested to ensure proper operation. Even with this testing, some field adjustments may be needed for telescoping. If the shade is telescoping, place a piece of high quality gaffer tape about 1" (25mm) wide on the exposed roller (where the fabric will cover it) on the side that the fabric will be drawn toward. For example: if the fabric is tracking to the left, place the tape on the right side. PLEASE READ - Cleaning and Maintenance Window covering products manufactured by Draper, when properly installed, should require no operational maintenance or lubrication. Most standard Draper fabrics may be cleaned at the window by vacuuming with a soft brush attachment. They also may be cleaned by using a sponge or soft cloth and mild solution of warm soapy water. A mild dishwashing liquid is recommended. A clean dry cloth is recommended for the metal finish. Please Note: Exceptions are GreenScreen Evolve, GreenScreen Revive, Flocké and Phifer SW7000 fabrics, which must be cleaned with a dry art sponge. page 2 of 12 Dual Roller Coupled Motorized FlexShades® (Large Hardware) Section 2 - Idler-End and Operator End Assemblies Please Note: The operator will already be installed in the operator-end roller; the sliding pin idler will also be installed in the idler-end roller. It is only necessary to install the coupler assemblies. Caution: Section 1.1 - 2" (51 mm) Idler-End Assembly Please Note: Notches in the tube need to be lined up with the "keys" on the couplers. 1. Insert coupler assembly into roller. Ensure the notch in the tube is lined up with the "key" on the coupler, and press until the assembly is fully seated in the roller. Section 1.2 - 2" (51 mm) Operator-End Assembly Please Note: Operator-end coupler assemblies will not slide straight in to the roller tube. 1. Insert assembly into the roller, with the "key" slightly off center from the notch. 2. Once assembly is far enough in that the ribs are past end of the notch, rotate the coupler until the notch is lined up with the "key" on the coupler. Please Note: If the assembly will not fully seat in the roller, retract the shaft (if applicable) and tap the assembly with a rubber mallet. Be careful not to damage the coupler. Section 1.3 - 3" (76 mm) Idler-End Assembly Please Note: The retractable shaft needs to be pointing toward the opposite end of the motor and oriented that direction for the whole unit. 1. Insert coupler assembly adapter into roller. Making sure the notch in the adapter is lined up with the notch in the coupler, press until the adapter is fully seated in the roller. 2. Insert coupler assembly into adapter. Making sure the notch in the inside of the adapter is lined up with the "key" on the coupler, press until the assembly is fully seated. Section 1.3 - 3" (76 mm) Operator-End Assembly 1. Follow the same steps used for the idler-end. Please Note: If the assembly will not fully seat in the roller, retract the shaft (if applicable) and tap the assembly with a rubber mallet. Be careful not to damage the coupler. • Ensure the locking ring on the idler-end coupler assembly is fully tightened before installing roller into brackets. There should be no play in the locking ring. If the locking ring is loose, then the idler is in "height adjustment" mode. • Wear a heavy glove on the hand used to grip the locking ring. • Tighten the locking ring until it is fully locked and it cannot rotate any further. Ensure it is tight and will not work loose. If locking ring cannot be tightened by hand, use a flat screwdriver or other tool to assist. OR C177.059SA C177.062SA OR C177.058SA C177.061SA Idler End Coupler Operator End Coupler C103.069 C177.061SA AND C103.069 C177.062SA AND Idler End Coupler Operator End Coupler Figure 2-A Figure 2-B Please Note: The retractable shaft must point toward the opposite end of the motor and oriented in that direction for the entire unit. Please Note: The retractable shaft must point toward the opposite end of the motor and oriented in that direction for the entire unit. Section 1 - Mounting Brackets Please Note: Installer is responsible for selecting mounting hardware appropriate for site conditions. 1. Mark wall, jamb, or ceiling for placement of mounting brackets. 2. Drill small starter hole (if necessary) in mounting surface. 3. Mount brackets using appropriate fasteners for surface. 4. Place operator (motor) end of rear shade into its bracket. 5. Secure motor plate with the provided clips. 6. Slide notched pin into idler bracket. Secure with retainer clip and lock into place with rotating idler lock. 7. Repeat with front shade. Retainer Clip Retainer Clip OPERATOR END IDLER END Figure 1 page 3 of 12 Dual Roller Coupled Motorized FlexShades® (Large Hardware)

Overview - Components CAUTION Read and understand all warnings (Page 2 of this document) before beginning installation. Contents Overview - Components .......................................................................................1 PLEASE READ - Important Safety and Installation Information ....................2 PLEASE READ - Field Adjustments, Cleaning and Maintenance ...................2 Section 1 - Idler-End and Operator End Assemblies ......................................3 Section 2 - Mounting / Assembly ........................................................................................4 Section 3 - Fascia Attachment ............................................................................5 Section 4 - Fabric/Roller Assembly Alignment ................................................6 Section 6 - Electrical Connections .................................................................7-8 Section 7 - Dimensions ..................................................................................9-10 TOOLS REQUIRED POWER DRILL PENCIL TAPE MEASURE HARDWARE (by others) LEVEL PLIERS FLEXSHADE F*MO Locking Ring SHADE FABRIC SHADE FABRIC Motor Plate Idler End Bracket Spanner Wrench Motor End Bracket Coupler Bracket Assembly } Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.7999 © 2021 All Rights Reserved | FORM: Coupled_DR_FS_MO_Standard_Hardware_Inst21 Dual Roller Coupled Motorized FlexShades® (Standard Hardware) INSTRUCTIONS INSTALLATION & OPERATION If you have any difficulties installing or servicing your Dual Roller Fascia Coupled FlexShades®, call your dealer or Draper, Inc. PERSONNEL REQUIRED WARNING Improper installation and use of the Dual Roller Fascia Coupled FlexShade® can result in serious injury or death. Primarily, injuries can occur if the unit falls due to imprecise installation, mishandling of the unit during installation or installation on an insufficient wall or ceiling structure. Please use extreme care. 1. Please read the following installation guidelines thoroughly and follow them carefully. Failure to do so may cause product to fall or otherwise fail, and could result in serious injury. 2. Installation and calibration of the unit should only be performed by an authorized, qualified, and experienced professional. In particular, electrical work and wiring [indicated in diagram by dashed lines] must be completed only by a qualified professional electrician who has read this manual completely and is familiar with the construction and operation of this equipment and the hazards involved. 3. Do not affix the unit to wall or ceilings that have inadequate strength to permanently hold the unit during use. It is the owner’s and installer’s responsibility to confirm the wall or ceiling to which the unit attaches is sufficient to permanently hold the weight and stress loads of the unit at all times. Draper, Inc., is not responsible for improper installation, application, testing, or workmanship related to the product at place of installation. 4. It is the installer’s responsibility to ensure appropriate fasteners are used for mounting. 5. All brackets, fascia, headboxes, pockets, wall clips, and other hardware must be installed level. Unit must be level and square. 6. Never leave the area while operating the unit during installation, maintenance, or normal operation, unless it is secure and safe. 7. Before testing or operation, carefully inspect the entire area and path of the shade and areas underneath the shade to be sure no persons or objects are in the area. 8. Turn off power and any nearby equipment or cables carrying electricity before connecting switches, wires, controls, or electrical components. 9. Ensure the limit switches are pointed down or accessible when placing the motor in brackets/endcaps. 10. All motors should be tested and limits set using test cord before shades are wired. 11. Do not wire motors in parallel without written permission from Draper, Inc. 12. During testing or operation, carefully watch the surrounding area for any potential safety concerns including nearby persons or objects. 13. After installation, the entire system, including all sensors, should be carefully tested to ensure safe and normal operation. Extreme care should be taken during testing to remain clear of moving parts to avoid possible injury. 14. Operation of unit should be performed only by authorized and qualified personnel, who have been trained in the safe and effective operation of the unit and understand its safety features. 15. The safety features of the unit , including sensors, should never be disabled, bypassed, or overridden. The system should not be operated until all safety features, including the sensors, are properly and completely installed, calibrated, and tested. 16. Unit may need to comply with local, state, or district rules and regulations, in particular when installed in schools. All applicable rules and regulations should be reviewed before installation and use. 17. Failure to precisely follow installation guidelines invalidates all warranties. 18. Custom products/installations may not be reflected in this manual. Call Draper, Inc., if you have questions about the installation of custom products or any questions about your installation. Before Beginning Installation 1. Look for any job site conditions that could interfere with installation or operation of the system. 2. Read carefully and be sure to understand all installation instructions and all related operations manuals. These instructions are intended to serve as a guide for the installer and owner. They should be followed closely and combined with the expertise of experienced qualified installers. Draper, Inc., is not responsible for improper installation, application, testing, or workmanship related to the product at place of installation. Please retain all instructions for future use. 3. Open cartons lengthwise. 4. Locate and lay out all pieces. 5. Inspect all boxes to ensure you have received the proper shade and parts. Controls may be shipped separately, or in same carton as shade. 6. If you have any difficulties with installing, servicing, or operating your shade, call your dealer or Draper, Inc., 765-987-7999. Important Safety Information Important Safety Information PLEASE READ - Important Installation Information Caution: 1. Inspect all boxes to ensure you have received the proper shades and parts. Controls may be shipped separately, or in same carton as shades. 2. Open cartons lengthwise. 3. Before mounting shades, verify measurements on label provided with shade, and ensure unit is installed at correct width. 4. Before connecting switches, controls, or electrical, ensure that power is turned OFF. Wiring indicated in diagram by dashed lines must be completed by an electrician. 5. Do not wire motors in parallel without written permission from Draper. 6. All endcaps, fascia, pocket headbox, and other hardware must be installed level. Shades must be level and square. 7. Read the following installation guidelines thoroughly and follow them carefully. Failure to do so may cause product to fall or otherwise fail, and invalidates warranty. 8. Installer is responsible for selecting mounting hardware appropriate for site conditions. PLEASE READ - Safety Information PLEASE READ - Field Adjustments Each Draper Solar Control Shade is tested to ensure proper operation. Even with this testing, some field adjustments may be needed for telescoping. If the shade is telescoping, place a piece of high quality gaffer tape about 1" (25mm) wide on the exposed roller (where the fabric will cover it) on the side that the fabric will be drawn toward. For example: if the fabric is tracking to the left, place the tape on the right side. PLEASE READ - Cleaning and Maintenance Window covering products manufactured by Draper, when properly installed, should require no operational maintenance or lubrication. Most standard Draper fabrics may be cleaned at the window by vacuuming with a soft brush attachment. They also may be cleaned by using a sponge or soft cloth and mild solution of warm soapy water. A mild dishwashing liquid is recommended. A clean dry cloth is recommended for the metal finish. Please Note: Exceptions are GreenScreen Evolve, GreenScreen Revive, Flocké and Phifer SW7000 fabrics, which must be cleaned with a dry art sponge. page 2 of 10 Dual Roller Coupled Motorized FlexShades® (Standard Hardware) Section 1 - Idler-End and Operator End Assemblies Please Note: The operator will already be installed in the operator-end roller; the sliding pin idler will also be installed in the idler-end roller. It is only necessary to install the coupler assemblies. Section 1.1 - 2" (51 mm) Idler-End Assembly Please Note: Notches in the tube need to be lined up with the "keys" on the couplers. 1. Insert coupler assembly into roller. Making sure the notch in the tube is lined up with the "key" on the coupler, press until the assembly is fully seated in the roller. Caution: • Ensure the locking ring on the idler-end coupler assembly is fully tightened before installing roller into brackets. There should be no play in the locking ring. If the locking ring is loose, then the idler is in "height adjustment" mode. • Wear a heavy glove on the hand used to grip the locking ring. • Tighten the locking ring until it is fully locked and it cannot rotate any further. Check to ensure it is tight and will not work loose. If locking ring cannot be tightened by hand, use a flat screwdriver or other tool to assist. Section 1.2 - 2" (51 mm) Operator-End Assembly Please Note: Operator-end coupler assemblies will not slide straight in to the roller tube. 1. Insert assembly into the roller, with the "key" slightly off center from the notch. 2. Once assembly is far enough in that the ribs are past end of the notch, rotate the coupler until the notch is lined up with the "key" on the coupler. Please Note: If the assembly will not fully seat in the roller, retract the shaft (if applicable) and tap the assembly with a rubber mallet. Be careful not to damage the coupler. Section 1.3 - 3" (76 mm) Idler-End Assembly Please Note: The retractable shaft needs to be pointing toward the opposite end of the motor and oriented that direction for the whole unit. 1. Insert coupler assembly adapter into roller. Making sure the notch in the adapter is lined up with the notch in the coupler, press until the adapter is fully seated in the roller. 2. Insert coupler assembly into adapter. Making sure the notch in the inside of the adapter is lined up with the "key" on the coupler, press until the assembly is fully seated. Caution: • Ensure the locking ring on the idler-end coupler assembly is fully tightened before installing roller into brackets. There should be no play in the locking ring. If the locking ring is loose, then the idler is in "height adjustment" mode. • Wear a heavy glove on the hand used to grip the locking ring. • Tighten the locking ring until it is fully locked and it cannot rotate any further. Check to ensure it is tight and will not work loose. If locking ring cannot be tightened by hand, use a flat screwdriver or other tool to assist. Section 1.3 - 3" (76 mm) Operator-End Assembly 1. Follow the same steps used for the idler-end. Please Note: If the assembly will not fully seat in the roller, retract the shaft (if applicable) and tap the assembly with a rubber mallet. Be careful not to damage the coupler. OR C177.059SA C177.062SA OR C177.058SA C177.061SA Idler End Coupler Operator End Coupler C103.069 C177.061SA AND C103.069 C177.062SA AND Idler End Coupler Operator End Coupler Figure 1a Figure 1b Please Note: The retractable shaft must point toward the opposite end of the motor and oriented in that direction for the entire unit. Please Note: The retractable shaft must point toward the opposite end of the motor and oriented in that direction for the entire unit. page 3 of 10 Dual Roller Coupled Motorized FlexShades® (Standard Hardware) Section 2 - Mounting / Assembly (Requires two (2) installers) Section 2.1 - Operating the Retractable Coupler Shaft (Fig. 2) Please Note: Custom products/installations may not be reflected by this document. Draper® Coupled FlexShades utilize a locking retractable shaft (Fig. 1) to hold roller assemblies in place and link panels together. The retractable coupler shaft on has three distinct positions: fully extended, intermediate, and fully retracted. 1. To retract the coupler shaft from fully extended to the intermediate position, grasp the roller with one hand while rotating the metal ring counterclockwise (as viewed facing the coupler assembly) approximately ½ of a turn with the other; this will leave the shaft extended approximately ½". 2. To retract the coupler shaft fully, rotate the metal ring counterclockwise (as viewed facing the coupler assembly) an additional 1/3"of a turn. 3. To lock shaft in place when extended, rotate metal ring clockwise ¼ turn. Caution:.Installation of this product requires two people. Caution: Before beginning installation, practice extending and retracting the coupler shaft in a fabric/roller assembly, following instructions in the "Operating the Retractable Coupler Shaft" section below. Caution: All motors should be tested and limits set using test cord before electrician wires shade. Please Note: Custom products/installations may not be reflected by this document. Call Draper, Inc. with any questions about product installation. Section 2.3 - First (Operator-end) Fabric Roller Assembly (Fig. 4) 1. If desired, the proper location of the coupler bracket assembly can be verified. Otherwise, proceed to step 2. Section 2.2 - Operator-end Bracket Assembly (Fig. 3) 1. Before mounting shades, verify measurements on the card provided with the shade, and ensure the brackets are installed at the correct width. 2. Measure and mark wall, jamb, or ceiling for placement of mounting brackets or endcaps. Mark a level line across all windows to ensure a level installation. Mark the outer edges of the operator- and idler-end brackets or endcaps, and the center locations of the coupler brackets. Locations are determined by: A. Operator-end panel width; B. Intermediate panel width(s); and C. Idler-end panel width. 3. Mount the operator-end bracket assembly (Fig. 3 for bracket/endcap types). Ensure the outside edge is aligned with the marked location. Please Note: There is no retractable shaft in the idler end assembly on the idler end shade (furthest from the operator). This idler assembly utilizes a sliding pin and retainer clip. Please Note: These instruction steps are for installing endcaps/brackets one at a time. Brackets/ endcaps may also all be installed at the same time, prior to installing roller/fabric assemblies. If brackets/endcaps are installed first, please be certain of measurements and locations. For best results, assemble the unit on a flat, clean surface and verify measurements before attaching brackets/endcaps. Caution: During installation and adjustment of coupled shades, fingers may slip, causing possibly severe cuts and/or scrapes. Wear gloves that are flexible enough to adjust the metal wheel but strong enough to prevent scrapes from surrounding metal or other surfaces. Please Note: Installer is responsible for selecting mounting hardware appropriate for site conditions. A. Installer #1 attaches the operator end to the operator-end bracket. B. Installer #2 slides the coupler bracket onto the coupler shaft of the fabric/roller assembly to be installed, and holds in place. C. Verify and mark location and set fabric/roller assembly aside. 2. Install first coupler bracket assembly to mounting surface. 3. Ensure the operator-end fabric/roller assembly's coupler shaft is completely retracted (see "Operating the Retractable Shaft" and Fig. 2). 4. Raise first rear/upper fabric/roller assembly into place. While Installer #1 inserts the operator end of fabric/roller assembly into the operator-end bracket, Installer #2 lifts the coupler end up next to the coupler bracket assembly, then extends the coupler shaft to the intermediate position by rotating the ring clockwise about 1/3 of a turn (see "Operating the Retractable Shaft" and Fig. 2). This will hold the first unit in place during installation of the next panel. 5. For motorized shades, connect power so the shade can be operated and adjusted. 6. Operate the shade to ensure proper fabric tracking and to set up and down limits (see sections on limit adjustment and field adjustments). 7. Raise shade to upper limit. R E T R A C T E X T E N D R E T R A C T E X T E N D R E T R A C T E X T E N D Idler-end Coupler Bracket Motor End Endcap Fascia Assembly-Fascia Endcap Fascia Figure 4 EXTEND RETRACT EXTEND RETRACT PERSONNEL REQUIRED Figure 2 Figure 3 page 4 of 10 Dual Roller Coupled Motorized FlexShades® (Standard Hardware)