Dromex DHFFM Manuals

Dromex: Unit 1, 1 Blase Road, New Germany, 3620, South Africa T. +27(31) 713 1960 E. [email protected] www.dromex.co.za FULL FACE MASK RESPIRATOR DH FFM Description The Dromex® DHFFM full face mask provides the user with unparalleled vision, comfort and reliability protecting against hazardous vapours, gases and particulates, provided there is sufficient oxygen present in the contaminated atmosphere. The Dromex® full face mask utilizes the Dromex® twin uni-fit cartridges and pre-filters only. Special Instructions All respiratory selections should be read in conjunction with BS EN 529:2005 “Respiratory Protective devices – Recommendations for selection, use, care and maintenance”. Do not use these respirators or enter in area where: • The oxygen concentration is not known or is less than 19.5%. • Contaminants or their concentrations are unknown or are known to be immediately dangerous to life or health. • Particulate concentrations exceed levels fixed by the applicable health and safety regulations or protection factor 40 NPF whichever is lower. • Gases and/or vapours are present except for respirators designated as protecting against vapours, in which case vapour concentrations should not exceed 20 NPF. • The requirement for leak tightness is unlikely to be achieved if worn against a beard or facial stubble. • Do not wear standard eye glasses with a full-face respirator • Not to be used for firefighting. • These respirators do not supply oxygen. Do NOT use in oxygen deficient atmospheres (e.g. tanks or other poorly ventilated areas). • Do not use in explosive atmospheres. • Do not modify or alter this device. Compliance & Conformity NRCS Homologated to SANS 50136:1998 CL1 as required by the Occupational Health and Safety Act, 1993 (Act No. 85 of 1993) EN136:2008 approved: Respiratory protective devices full face masks — Requirements, testing, marking quality system as per ISO9001:2008. Specifications Type: Class1 full face masks for light duty use Material: Thermo Plastic Elastomer/Rubber Colour: Black Harness: 5-point comfort harness with 2 grip holes for easier fitting on and removing with gloves and accommodation of women’s hair (ability to wear a pony tail). Withstands a pull of up to 15KG or 150N Visor: Polycarbonate anti-fog and impact resistant with peripheral optical vision of 220 degree’s (110 on the left and right). The natural field of vision is greater than the 70% specified of EN136:2008 standards. One size mask body: Accommodates small to large facial size's Temperature: Designed to withstand temperatures of up to 70 ± 3˚ Light weight dual filter cartridge system evenly distributes weight of mask and cartridges on the face. DHFFM 10 -20˚C +40˚C <75% RH DHFFM Packaging, Storage & Obsolescence DHFFM - Packed individually sealed in cardboard box,10 masks per carton for shipping. When not in use, store the full-face mask with filters in the Dromex® full face mask storage bag that can be worn on the operator’s waist. Store in a cool dry place, away from direct sunlight at temperature between-20˚C and + 40˚C and where relative humidity is less than 75% and away from sources of possible contamination and physical damage. Cleaning & Maintenance - Remove cartridge filters from connectors and all inhalation and exhalations valves. - Clean / disinfect the face piece and components with a damp cloth, using lukewarm with all-purpose detergent (neutral, pH 6-8, e.g.: washing-up liquid), warm soapy water or cleaning solution not exceeding 30 degrees. - Do not immerse the product in water or use abrasive cleaners. - Do not use solvents (e.g alcohol, acetone, turpentine), hot water, strong detergents, bleaches or petroleum based products to clean any part of masks. - Dry in air at room temperature. - Replace all components after cleaning and inspect for visible damage. Shelf life 5 years, with correct maintenance and storage procedures. Discard immediately if mask is damaged and tears are visible. Materials None of the materials used in the manufacture are known to adversely affect the hygiene or health. Disposal All industrial waste should be disposed of correctly according to local regulations and good disposal practice. Respiratory protective devices should be disposed of considering the hazardous substance they were used for. Please consider recycling.