DSC Power832 Manuals

1 S E C T I O N 1 1.1 Specifications Control Panel Specifications Flexible Zone Configuration: • 8 Fully Programmable Zones • 37 Access Codes: 32 User, 1 System Master, 2 Partition Master and 2 Duress • Expandable to 32 Zones • Hardwired expansion available using the PC5108 Eight Zone Expansion Module • Wireless expansion available using the PC5132 Wireless Zone Expansion Module (up to 32 wireless zones, 900MHz, True Spread Spectrum Technology, Fully Supervised) • Normally Closed, Single EOL, or Double EOL zone supervision • 2-Wire Smoke Zone • 27 Zone Types, 8 Programmable Zone Options • 2 Partitions Audible Alarm Output: • Supervised Bell Output (current limited at 3 amps), 12 VDC • Steady or Pulsed Output EEPROM Memory: • Will not lose programming or system status on complete AC and Battery failure Programmable Outputs: • Up to 14 Programmable Voltage Outputs, 18 programmable options • One High Current (300 mA) PGM output with 2 wire smoke detector capability on main panel • Maximum Loop Current is 1.5 mA when the 2-wire smoke detector configuration is used • One Low Current (50 mA) PGM output on main panel • Eight Additional Low Current (50 mA) PGM outputs available using the PC5208 module • Four High Current (1 Amp) PGM outputs Available Using the PC5204 module • 1 PC5204 Output Fully Supervised for Siren Output Powerful 1 Amp Regulated Power Supply: • 500 mA Auxiliary Supply, 12 VDC • Positive Temperature Coefficient (PTC) components replace fuses • Supervision for loss of AC Power, Low Battery • Internal Clock Locked to AC Power Frequency Power Requirements: • Transformer = 16.5 VAC, 40VA • Battery = 12 volt 4 Ah minimum rechargeable sealed lead acid Remote Keypad Specifications: • 4 Different Keypads Available: - PC5508/KP5508 8 Zone LED Keypad - PC5516/KP5516 16 Zone LED Keypad - PC5532/KP5532 32 Zone LED Keypad - LCD5500/KPL5500 Alphanumeric Keypad • Each Keypad has 5 Fully Programmable Function Keys • Connect up to 8 Keypads • Four Wire (Quad) Connection to Keybus • Built in Piezoelectric Buzzer Digital Communicator Specifications: • Supports all Major Formats including SIA and Contact ID • Event Initiated Personal Paging • 3 Programmable Phone Numbers • 2 Account numbers • Supports LINKS1000 Cellular Communication • DTMF and Pulse Dialing • DPDT Line Seizure • Anti-jam Feature • Split Reporting of Selected Transmissions to Each Telephone Number System Supervision Features The PC5010 continuously monitors a number of possible trouble conditions including: • AC Power Failure • Trouble by Zone • Fire Trouble • Telephone Line Trouble • Low Battery Condition • Bell Output Trouble • Loss of Internal Clock • AUX Power Supply Fault • Tamper by Zone • Failure to Communicate • Module Fault (Supervisory or Tamper) System Introduction

Instruction Manual PC5O15 v2.2 WARNING This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read.

1 16 About Your Security System Your DSC Power832 Security System has been designed to provide you with the greatest possible flexibility and convenience. Read this manual carefully and have your installer instruct you on your system's operation and on which features have been implemented in your system. All users of this system should be equally instructed in its use. Fill out the “System Information” page with all of you zone information and access codes and store this manual in a safe place for future reference. Fire Detection This equipment is capable of monitoring fire detection devices such as smoke detectors and providing a warning if a fire condition is detected. Good fire detection depends on having adequate number of detectors placed in appropriate locations. Carefully review the Family Escape Planning guidelines in this manual. NOTE: Your installer must enable the fire detection portion of this equipment before it becomes functional. Testing To insure that your system continues to function as intended, you must test your system weekly. Please refer to “Testing Your System” on page 13 of this manual. If your system does not function properly, call your installing company for service. Monitoring This system is capable of transmitting alarms, troubles and emergency information over telephone lines to a monitoring station. If you inadvertently initiate an alarm, immediately call the monitoring station to prevent an unnecessary response. NOTE: The monitoring function must be enabled by the installer before it becomes functional. General System Operation Your security system is made up of a DSC Power832 control panel, one or more Power832 keypads and various sensors and detectors. The control panel will be mounted out of the way in a utility closet or in a basement. The metal cabinet contains the system electronics, fuses and stand-by battery. There is normally no reason for anyone but the installer or service professional to have access to the control panel. All the keypads have an audible indicator and command entry keys. The LED keypads have a group of zone and system status lights. The LCD keypad has an alphanumeric liquid crystal display (LCD). The keypad is used to send commands to the system and to display the current system status. The keypad(s) will be mounted in a convenient location inside the protected premises close to the entry/ exit door(s). The security system has several zones of area protection and each of these zones will be connected to one or more sensors (motion detectors, glassbreak detectors, door contacts, etc.). A sensor in alarm will be indicated by the corresponding zone lights flashing on a LED keypad or by written messages on the LCD keypad. IMPORTANT NOTICE A security system cannot prevent emergencies. It is only intended to alert you and – if included – your monitoring station of an emergency situation. Security systems are generally very reliable but they may not work under all conditions and they are not a substitute for prudent security practices or life and property insurance. Your security system should be installed and serviced by qualified security professionals who should instruct you on the level of protection that has been provided and on system operations. • Each person should know of a predetermined assembly point where everyone can be accounted for i.e.: across the street or at a neighbour's house. Once everyone is out of the building, call the Fire Department. • A good plan emphasizes quick escape. Do not investigate or attempt to fight the fire, and do not gather belongings or pets as this wastes valuable time. Once outside, do not re-enter the house. Wait for the fire department. • Write the fire escape plan down and rehearse it frequently so that should an emergency arise, everyone will know what to do. Revise the plan as conditions change, such as the number of people in the home, or if there are changes to the building's construction. • Make sure your fire warning system is operational by conducting weekly tests (see “Fire Alarm Operation” on page 14). If you are unsure about system operation, contact your installing dealer. • We recommend that you contact your local fire department and request further information on fire safety and escape planning. If available, have your local fire prevention officer conduct an in- house fire safety inspection. Maintenance With normal use, the system requires minimum maintenance. The following points should be observed. 1.Do not wash the security station with a wet cloth. Light dusting with a slightly moistened cloth should remove normal accumulations of dust. 2.The battery/ bell test is designed to determine battery condition. We recommended, however, that the stand-by batteries be replaced every three years. 3.For other system devices such as smoke detectors, passive infrared, ultrasonic or microwave motion detectors or glassbreak detectors, consult the respective manufacturer’s literature for testing and maintenance.

1 About Your Security System Your DSC Power832 Security System has been designed to provide you with the greatest possible flexibility and convenience. Read this manual carefully and have your installer instruct you on your system's operation and on which features have been implemented in your system. All users of this system should be equally instructed in its use. Fill out the “System Information” page with all of you zone information and access codes and store this manual in a safe place for future reference. Fire Detection This equipment is capable of monitoring fire detection devices such as smoke detectors and providing a warning if a fire condition is detected. Good fire detection depends on having adequate number of detectors placed in appropriate locations. This equipment should be installed in accordance with NFPA 72 (N.F.P.A., Batterymarch Park, Quincey MA 02269). Carefully review the Family Escape Planning guidelines in this manual. NOTE: Your installer must enable the fire detection portion of this equipment before it becomes functional. Testing To insure that your system continues to function as intended, you must test your system weekly. Please refer to “Testing Your System” on page 13 of this manual. If your system does not function properly, call your installing company for service. Monitoring This system is capable of transmitting alarms, troubles and emergency information over telephone lines to a monitoring station. If you inadvertently initiate an alarm, immediately call the monitoring station to prevent an unnecessary response. NOTE: The monitoring function must be enabled by the installer before it becomes functional. General System Operation Your security system is made up of a DSC Power832 control panel, one or more Power832 keypads and various sensors and detectors. The control panel will be mounted out of the way in a utility closet or in a basement. The metal cabinet contains the system electronics, fuses and stand-by battery. There is normally no reason for anyone but the installer or service professional to have access to the control panel. All the keypads have an audible indicator and command entry keys. The LED keypads have a group of zone and system status lights. The LCD keypad has an alphanumeric liquid crystal display (LCD). The keypad is used to send commands to the system and to display the current system status. The keypad(s) will be mounted in a convenient location inside the protected premises close to the entry/ exit door(s). The security system has several zones of area protection and each of these zones will be connected to one or more sensors (motion detectors, glassbreak detectors, door contacts, etc.). A sensor in alarm will be indicated by the corresponding zone lights flashing on a LED keypad or by written messages on the LCD keypad. IMPORTANT NOTICE A security system cannot prevent emergencies. It is only intended to alert you and – if included – your monitoring station of an emergency situation. Security systems are generally very reliable but they may not work under all conditions and they are not a substitute for prudent security practices or life and property insurance. Your security system should be installed and serviced by qualified security professionals who should instruct you on the level of protection that has been provided and on system operations.