DUAL LITE SEMPRA SEWL Series Manuals

Severe Conditions Die-Cast Aluminum LED Exit Sign Installation Instructions SEWL Series Hubbell Lighting, Inc. Life Safety Products • www.dual-lite.com Copyright© Hubbell Lighting, Inc., All Rights Reserved • Specifications subject to change without notice. • Printed in U.S.A. 93016017 D 2/19 Self-Testing/Self-Diagnostic Models All models ordered with the Dual-Lite Spectron self-testing/self-diagnostic electronics system provide: ■ Visual indication of AC power status ■ Visual indication of all self-diagnostic test cycles ■ Visual indication of unit malfunctions including: ■ Battery fault ■ Charger fault ■ Transfer Fault ■ Lamp fault Bi-Color LED Status Indicator Self-testing/self-diagnostic units are provided with a single, bi-color LED which serves as a combination AC power, self-test and service alert status indicator. During normal operation, the green status LED will be constantly illuminated, indicating the presence of AC power. During all automatic or manual self-test cycles, the green Status LED will blink at a one cycle per second rate indicating “Test In Progress". If a fault condition is detected during any automatic or manual self-test cycle, upon comple- tion of test, the red status indicator will provide a “service alert code” – see table below. Service Alert Code Description One blink ON/pause Battery not connected Two blinks ON/pause Battery fault Three blinks ON/pause Charger fault Four blinks ON/pause Transfer circuit fault Five blinks ON/pause Lamp failure Manual Test Using the unit test switch, users can initiate different duration test cycles based on the following table: To Initiate Action: Test Cycle Press switch once 1 minute Press switch twice 90 minute Pressing test switch at any time after a test cycle has begun cancels the remainder of test and returns the unit to normal operation. (NOTE: Batteries are often shipped in a discharged state – this is normal – battery requires charging. Allow several hours of charge before testing unit.) Spectron units also provide: Brownout protection – unit transfer to emergency mode with low AC input voltage. Time Delay Re-transfer – unit will remain in emergency mode for additional time after AC power is restored. TROUBLESHOOTING AC-On Light does not illuminate • Check AC wiring connections Emergency LEDs do not work • Battery is shipped disconnected. Connect leads from battery to charger PCB and charge before testing. • Make sure connections to charger board are properly seated. • Check wiring connections. Maintenance Exit signs should be tested and maintained in accor- dance with National Electrical Code and NFPA 101 Life Safety Code requirements. It is recommended that exit signs be tested for a minimum of 30 seconds once a month and 90 minutes once a year. The automatic monthly tests of the Spectron units satisfy this requirement. The required annual test can be initi- ated manually with the test switch, as required by the safety code. RECYCLING INFORMATION All aluminum components are recyclable. All cartons contain recycled materials. Please recycle. NOTICE: Exit signs contain rechargeable batteries which must be recycled or disposed of properly. Use CAUTION when handling batteries. LED REPLACEMENT (Contact factory) IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following. READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. Do not let power supply cords touch hot surfaces. 2. Do not mount near gas or electric heaters. 3. Equipment should be mounted in locations and at heights where it will not readily be subject to tampering by unauthorized personnel. 4. The use of accessory equipment not authorized by the manufacturer may cause an unsafe condition. 5. Do not use this equipment for other than its intended purpose. 6. Service of this equipment should be performed by qualified service personnel. SAVE THESE INSTRUCTIONS 93021636 93021638 93021640 93021641 93021643 93021644 93021645 93021646 WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/ or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product. 93021636 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CEILING OR END MOUNT INSTALLATION WALL MOUNT INSTALLATION TRANSFORMER CONNECTOR TO CHARGER (J1) WIRE HARNESS FROM HEATER ASSY 7 PIN CONNECTOR TO GROUND CONNECTION ON FRAME 277 120 COM TO JUNCTION BOX 3 PIN PUSH CONNECTOR (QTY 4) SUPPLIED PIGTAIL LEADS PREWIRED AT FACTORY BLK WHT GREEN (GROUND) PIGTAIL LEAD RED PIGTAIL LEAD BLK PIGTAIL LEAD WHT PIGTAIL LEAD ORG BLK WHT GREEN WIRING DIAGRAM 10. REMOVE CHEVRON(S) IF REQUIRED. DRIVE CHEVRON TOWARDS BACK OF STENCIL BY TAPPING AROUND THE ENTIRE PERIMITER FROM FRONTSIDE OF STENCIL FOR CLEAN BREAKOUT. 2. REMOVE APPROPRIATE KNOCKOUTS FOR WALLBOX SCREWS. 4. ATTACH PRE-TINNED PIGTAIL LEADS PROVIDED TO AC INPUT CONDUCTORS. 3. IF USING CONDUIT, REMOVE PIPE PLUG, OTHERWISE REMOVE CENTER KNOCKOUT. 5. REMOVE ADHESIVE BACKING FROM MOUNTING GASKET & APPLY TO EXIT BACKPLATE. 6. ROUTE PIGTAIL LEADS THRU CENTER KNOCKOUT IN BACKPLATE & MOUNT SIGN TO WALLBOX. 7. ATTACH ADHESIVE WIRING SADDLE AND ROUTE WIRES INTO CHANNEL. (SEE DETAIL 1) 8. ROUTE PIGTAILS THRU LIGHTBOX (SEE WIRING DIAGRAM & DETAIL 1) AND MAKE PROPER CONNECTIONS USING PUSH CONNECTORS. 9. ATTACH 2-PIN BATTERY CONNECTOR TO PC BOARD AS SHOWN. (SEE DETAIL 1) 11. CONFIRM ALL WIRING IS DRESSED PROPERLY, HANG STENCIL & DIFFUSER ONTO FRAME PINS .(SEE DETAIL 1) 12. SEAT COVER & SECURELY TIGHTEN COVER SCREWS. (SEE DETAIL 3) PIGTAIL ROUTING FROM CEILING CANOPY TO PUSH CONNECTORS LEADS TO PASS THRU SLOT IN LIGHT BOX (WALL MTG) LEADS TO BE SECURED BY WIRE SADDLE (PROVIDED) (WALL MTG) PUSH CONNECTORS (QTY 4) SEE WIRING DIAGRAM FOR CONNECTION INSTRUCTIONS PIGTAIL ROUTING FROM SIDE MOUNTED CANOPY TO PUSH CONNECTORS PIGTAIL ROUTING FROM CENTER KO ON BACKPLATE TO PUSH CONNECTORS 2-PIN BATTERY CONNECTION AC TRANSFORMER 120VAC-CONNECT BLACK & WHITE LEADS. 277VAC-CONNECT RED & WHITE LEADS. 13. REMOVE CHEVRON(S) IF REQUIRED. DRIVE CHEVRON TOWARDS BACK OF STENCIL BY TAPPING AROUND THE ENTIRE CHEVRON PERIMITER FROM FRONTSIDE OF STENCIL FOR CLEAN BREAKOUT. 3. ATTACH PRE-TINNED PIGTAIL LEADS PROVIDED TO AC INPUT CONDUCTORS. 2. REMOVE PIPE PLUG. 4. FEED LEADS THROUGH CENTER OF UNIVERSAL MOUNTING PLATE AND ATTACH PLATE TO ELECTRICAL BOX. 5. AFFIX NUT TO PIPE NIPPLE. SLIP THROUGH CANOPY CENTER HOLE AND AFFIX SECOND NUT ONTO PIPE NIPPLE AND TIGHTEN. THIS WILL LOCK PIPE NIPPLE TO CANOPY. (SEE DETAIL) 7. ROUTE PIGTAILS THRU GASKET & CANOPY. 6. REMOVE ADHESIVE BACKING FROM MOUNTING GASKET & APPLY TO CANOPY. 8. WITH SCREWS SUPPLIED (QTY 2) SECURE CANOPY TO UNIVERSAL MOUNTING PLATE 9. REMOVE ADHESIVE BACKING FROM FRAME GASKET, ROUTE PIGTAILS THROUGH GASKET & APPLY TO CANOPY. (SEE DETAIL 2) 10. ROUTE PIGTAILS THROUGH EXIT FRAME AND PIPE NIPPLE NUT. AFFIX NUT TO PIPE NIPPLE AND TIGHTEN TO SECURE EXIT FRAME. (SEE DETAIL 2) 11. ROUTE PIGTAILS TO PUSH CONNECTORS. (SEE WIRING DIAGRAM & DETAIL 1) 12. ATTACH 2-PIN BATTERY CONNECTOR TO PC BOARD AS SHOWN. (SEE DETAIL 1) 14. CONFIRM ALL WIRING IS DRESSED PROPERLY, HANG STENCIL/DIFFUSER ONTO FRAME PINS. (SEE DETAIL 1) 15. SEAT COVER(S) & SECURELY TIGHTEN COVER(S) SCREWS. (SEE DETAIL 3) DETAIL 2 CANOPY GASKET COMPRESSION STOPS CANOPY ANTI-ROTATION RIBS NOTE: PIPE NIPPLE NUT INSIDE EXIT FRAME SHALL BE TIGHTENED SO THAT CANOPY GASKET COMPRESSION STOPS SEAT AGAINST EXIT FRAME. THIS INSURES THAT THE GASKET IS COMPRESSED PROPERLY TO SEAL SIGN & SIGN WILL BE SECURE AGAINST ROTATING ON CANOPY. GASKET NOTE: CLEAR POLYCARBONATE COVER(S) ARE SIMILAR TO THE CANOPY IN THAT THEY ALSO HAVE COMPRESSION STOPS (COVER HAS THEM AT ALL 4 CORNERS) THAT SEAT AGAINST EXIT FRAME. THIS INSURES GASKET WILL BE COMPRESSED PROPERLY TO SEAL SIGN. DETAIL 3 SEAT COVER TO FRAME DETAIL 1 FRAME PINS CENTER KNOCKOUT 1. USE SPANNER SCREW BIT (PROVIDED) TO REMOVE & TIGHTEN ALL SPANNER SCREWS. 1. USE SPANNER SCREW BIT (PROVIDED) TO REMOVE & TIGHTEN ALL SPANNER SCREWS. CANOPY PIPE NIPPLE NUT APPROX. 3/16" NOTE: FOR END MOUNTED SINGLE FACED SIGNS, THE BACKPLATE AND CLEAR COVER WITH STENCIL/DIFFUSER CAN BE SWAPPED FOR MOUNTING VERSATILITY A DETAIL A IMPORTANT: TO WEATHERPROOF FOR OUTDOOR INSTALLATION, BE SURE TO SEAL ALL OPENINGS — MOUNTING, CONDUIT, ETC. IMPORTANT: TO WEATHERPROOF FOR OUTDOOR INSTALLATION, BE SURE TO SEAL ALL OPENINGS — MOUNTING, CONDUIT, ETC. 93021644 93021643 93021641 93021640 93021638 93021646 93021645