Eaton 600 A 15 kV class PUSH-OP Manuals

600 A 15/25 and 35 kV class push-OP insulated standoff bushing installation instructions PUSH HERE DEADBREAK EYEBOLT LATCH HANDLE PUSH PLATE FIRST NOTCHES LOCKING TEETH BAIL BRACKET LOCKING SLOT OPTIONAL HITCH PIN COOPER POWER SERIES Deadbreak Apparatus Connectors MN650055EN Effective May 2017 Supersedes May 2009 (S600-65-1)

600 A 15/25 kV class PUSH-OP® deadbreak connector installation instructions COOPER POWER SERIES Deadbreak Apparatus Connectors MN650057EN Effective May 2017 Supersedes May 2014 (S600-13-3)

600 A 15 and 25 kV class PUSH-OP™ insulated standoff bushing General Eaton meets the full requirements of IEEE Std 386™-2006 standard, Separable Insulated Connector Systems with its Cooper Power™ series 600 A, 15 and 25 kV insulated PUSH-OP™ standoff bushing. The bushing provides a single deadbreak interface made of high quality insulating epoxy material. It is used in switchgear, transformers, and other apparatus to isolate and sec tion al ize an energized cable. Temporary or permanent parking of energized 600 A 15 and 25 kV PUSH-OP deadbreak connectors is simplified with the use of an insulated standoff bushing. The PUSH-OP insulated standoff bushing is de signed to be installed in the parking stand mounted on a switchgear, transformer, or other apparatus. A drain wire lug is pro vid ed on the standoff bracket for at tach ment of a drain wire lead to ensure deadfront construction. The bushing provides a fully-shielded, submersible connection for deadbreak operation. All standoff bushing brackets have a stainless steel eyebolt with a brass pressure foot. The bushing body is bolted to a stainless steel base bracket using a stainless steel bolt. The bracket and latch mechanism provides easy installation of a PUSH-OP connector without any threading operations. Installation A clampstick tool is used to place the standoff bushing in the parking stand on the front plate of the apparatus. The PUSH-OP connector is then installed onto the standoff bushing tap. Refer to Service Information S600-65-1 600 A 15/25 and 35 kV Class PUSH-OP Insulated Standoff Bushing Installation Instructions for complete installation details. Production tests Tests are conducted in accordance with IEEE Std 386™-2006 standard. • ac 60 Hz 1 Minute Withstand • 40 kV • Minimum Corona Voltage Level • 19 kV Tests are conducted in accordance with Eaton requirements. • Physical Inspection • Periodic Dissection • Periodic Fluoroscopic Analysis Deadbreak Connectors Catalog Data CA650043EN Effective April 2015 Supersedes 600-25 August 2002 COOPER POWER SERIES

600 A 15 kV class PUSH-OP™ insulated adapter cap General Eaton's Cooper Power™ series 600 A, 15 kV Class PUSH-OP™ adapter cap is a factory assembled LRTP and T-body with a stainless steel shroud and tin-plated copper probe. It meets all the requirements of IEEE Std 386™-2006 standard, Separable Connector Sys tems. The PUSH-OP adapter cap has a non-bolted connection that eliminates any need for threading and its associated problems. The device is used to cap a 600 A PUSH-OP type bushing tap inter face with the 200 A loadbreak interface allowing for live testing and visible grounding. The 200 A tap is three-phase switch ing and three-phase fault close rated. Used with a 200 A insulated pro tec tive cap, Eaton's Cooper Power series M.O.V.E. arrester or ground ing elbow, a PUSH-OP adapter cap provides a fully shielded, sub mers ible unit. Installation The PUSH-OP adapter cap is installed on a de-energized 600 A special PUSH-OP bushing inter face using a clampstick. Refer to Service Information S600-19-1 600 A 15, 25, and 35 kV Class PUSH-OP Bushing Adapter Cap Installation Instructions for details. Installation of the factory assembled LRTP and T-body to the 600 A PUSH-OP bushing requires no threading. Production tests Tests are conducted in accordance with IEEE Std 386™-2006 standard. • ac 60 Hz 1 Minute Withstand • 34 kV • Minimum Corona Voltage Level • 11 kV Tests are conducted in accordance with Eaton requirements. • Physical In spec tion • Periodic Dissection • Periodic Fluoroscopic Analysis Deadbreak Connector Catalog Data CA650019EN Effective April 2015 Supersedes 600-19 January 1990 COOPER POWER SERIES

600 A 15, 25, and 35 kV class PUSH-OP bushing adapter cap installation instructions COOPER POWER SERIES Deadbreak Apparatus Connectors MN650050EN Effective May 2017 Supersedes January 2010 (S600-19-1)