ebm-papst D3G146-AH50-11 Manuals

Operating instructions D3G146-AH50-11 Translation of the original operating instructions ebm-papst Mulfingen GmbH & Co. KG Bachmühle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 [email protected] www.ebmpapst.com CONTENTS 1. SAFETY REGULATIONS AND NOTES 1 1. SAFETY REGULATIONS AND NOTES Please read these operating instructions carefully before starting to work with the device. Observe the following warnings to prevent malfunctions or physical damage to both property and people. These operating instructions are to be regarded as part of this device. If the device is sold or transferred, the operating instructions must accompany it. These operating instructions may be duplicated and forwarded for information about potential dangers and their prevention. 1.1 Levels of hazard warnings 1 1.1 Levels of hazard warnings These operating instructions use the following hazard levels to indicate potentially hazardous situations and important safety regulations: DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Compliance with the measures is mandatory. WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Exercise extreme caution while working. CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or damage of property. NOTE A potentially harmful situation can occur and, if not avoided, can lead to property damage. 1.2 Staff qualification 1 1.2 Staff qualification The device may only be transported, unpacked, installed, operated, maintained and otherwise used by qualified, trained and authorised technical staff. Only authorised specialists are permitted to install the device, to carry out a test run and to perform work on the electrical installation. 1.3 Basic safety rules 1 1.3 Basic safety rules Any safety hazards stemming from the device must be re-evaluated once it is installed in the end device. The local industrial safety regulations must always be observed when working on the device. Keep the workplace clean and tidy. Untidiness in the working area increases the risk of injury. Observe the following when working on the unit: ; Do not make any modifications, additions or conversions to the device without the approval of ebm-papst. 1.4 Electrical voltage 1 1.4 Electrical voltage ; Check the electrical equipment of the device at regular intervals, refer to chapter 6.2 Safety test. ; Replace loose connections and defective cables immediately. DANGER Electrical load on the device Risk of electric shock → Stand on a rubber mat if you are working on an electrically charged device. 2 1.5 Safety and protective functions 2 1.6 Electromagnetic radiation 2 1.7 Mechanical movement 2 1.8 Emission 2 1.9 Hot surface 2 1.10 Transport 2 1.11 Storage 3 2. PROPER USE 4 3. TECHNICAL DATA 4 3.1 Product drawing 5 3.2 Nominal data 5 3.3 Data in accordance with ecodesign regulation EU 327/2011 5 3.4 Technical features 6 3.5 Mounting data 6 3.6 Transport and storage conditions 6 3.7 Electromagnetic compatibility 6 4. CONNECTION AND START-UP 6 4.1 Connecting the mechanical system 6 4.2 Connecting the electrical system 7 4.3 Connection of the cables 8 4.4 Connection screen 9 4.5 Checking the connections 9 4.6 Switch on device 9 4.7 Switching off the device 9 5. INTEGRATED PROTECTIVE FUNCTIONS 9 6. MAINTENANCE, MALFUNCTIONS, POSSIBLE CAUSES AND REMEDIES 10 6.1 Cleaning 10 6.2 Safety test 10 6.3 Disposal Item no. 50037-5-9970 · ENG · Revision 212353 · Release 2020-05-07 · Page 1 / 11 ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com

Operating instructions D3G146-AH50-11 Translation of the original operating instructions ebm-papst Mulfingen GmbH & Co. KG Bachmühle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 [email protected] www.ebmpapst.com CONTENTS 1. SAFETY REGULATIONS AND INFORMATION 1 1. SAFETY REGULATIONS AND INFORMATION Read these operating instructions carefully before starting work on the device. Observe the following warnings to prevent malfunctions or danger to persons. These operating instructions are to be regarded as part of the device. The device is only to be sold or passed on together with the operating instructions. These operating instructions may be duplicated and distributed to inform about potential dangers and their prevention. 1.1 Hazard levels for warnings 1 1.1 Hazard levels for warnings These operating instructions use the following hazard levels to indicate potentially hazardous situations and important safety regulations: DANGER Indicates an imminently hazardous situation which will result in death or serious injury if the specified actions are not taken. Compliance with the instructions is imperative. WARNING Indicates a potentially hazardous situation which can result in death or serious injury if the specified actions are not taken. Exercise extreme caution while working. CAUTION Indicates a potentially hazardous situation which can result in minor or moderate injury or damage to property if the specified actions are not taken. NOTE A potentially harmful situation can occur and, if not avoided, can lead to property damage. 1.2 Staff qualifications 1 1.2 Staff qualifications The device may only be transported, unpacked, installed, operated, maintained and otherwise used by suitably qualified, trained and authorized technical staff. Only authorized specialists are permitted to install the device, to carry out a test run and to perform work on the electrical installation. 1.3 Basic safety rules 1 1.3 Basic safety rules The safety hazards associated with the device must be assessed again following installation in the final product. The locally applicable industrial safety regulations are always to be observed when working on the device. Keep the workplace clean and tidy. Untidiness in the work area increases the risk of accidents. Note the following when working on the device: ; Do not perform any modifications, additions or conversions on the device without the approval of ebm-papst. 1.4 Voltage 1 1.4 Voltage ; Check the device's electrical equipment at regular intervals; see Chapter 6.2 Safety inspection. ; Replace loose connections and defective cables immediately. DANGER Electrically charged device Risk of electric shock → When working on an electrically charged device, stand on a rubber mat. 2 1.5 Safety and protective features 2 1.6 Electromagnetic radiation 2 1.7 Mechanical movement 2 1.8 Emissions 2 1.9 Hot surface 2 1.10 Transport 2 1.11 Storage 3 2. INTENDED USE 4 3. TECHNICAL DATA 4 3.1 Product drawing 5 3.2 Nominal data 5 3.3 Data according to Commission Regulation (EU) 327/2011 5 3.4 Technical description 6 3.5 Mounting data 6 3.6 Transport and storage conditions 6 3.7 Electromagnetic compatibility 6 4. CONNECTION AND STARTUP 6 4.1 Mechanical connection 6 4.2 Electrical connection 7 4.3 Connecting the cables 8 4.4 Connection diagram 9 4.5 Checking connections 9 4.6 Switching on the device 9 4.7 Switching off the device 9 5. INTEGRATED PROTECTIVE FEATURES 9 6. MAINTENANCE, MALFUNCTIONS, POSSIBLE CAUSES AND REMEDIES 10 6.1 Cleaning 10 6.2 Safety inspection 10 6.3 Disposal Item no. 50037-5-9970 · ENU · Change 212353 · Approved 2020-05-07 · Page 1 / 11 ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com