ebm-papst K3G355-AY43-52 Manuals

Operating instructions K3G355-AY43-52 Translation of the original operating instructions ebm-papst Mulfingen GmbH & Co. KG Bachmühle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 [email protected] www.ebmpapst.com CONTENTS 1. SAFETY REGULATIONS AND INFORMATION 1 1. SAFETY REGULATIONS AND INFORMATION Read these operating instructions carefully before starting work on the device. Observe the following warnings to prevent malfunctions or danger to persons. These operating instructions are to be regarded as part of the device. The device is only to be sold or passed on together with the operating instructions. These operating instructions may be duplicated and distributed to inform about potential dangers and their prevention. 1.1 Hazard levels for warnings 1 1.1 Hazard levels for warnings These operating instructions use the following hazard levels to indicate potentially hazardous situations and important safety regulations: DANGER Indicates an imminently hazardous situation which will result in death or serious injury if the specified actions are not taken. Compliance with the instructions is imperative. WARNING Indicates a potentially hazardous situation which can result in death or serious injury if the specified actions are not taken. Exercise extreme caution while working. CAUTION Indicates a potentially hazardous situation which can result in minor or moderate injury or damage to property if the specified actions are not taken. NOTE A potentially harmful situation can occur and, if not avoided, can lead to property damage. 1.2 Staff qualifications 1 1.2 Staff qualifications The device may only be transported, unpacked, installed, operated, maintained and otherwise used by suitably qualified, trained and authorized technical staff. Only authorized specialists are permitted to install the device, to carry out a test run and to perform work on the electrical installation. 1.3 Basic safety rules 1 1.3 Basic safety rules The safety hazards associated with the device must be assessed again following installation in the final product. The locally applicable industrial safety regulations are always to be observed when working on the device. Keep the workplace clean and tidy. Untidiness in the work area increases the risk of accidents. Note the following when working on the device: ; Do not perform any modifications, additions or conversions on the device without the approval of ebm-papst. 1.4 Voltage 1 1.4 Voltage ; Check the device's electrical equipment at regular intervals; see Chapter 6.3 Safety inspection. ; Replace loose connections and defective cables immediately. DANGER Electrically charged device Risk of electric shock → When working on an electrically charged device, stand on a rubber mat. 2 1.5 Safety and protective features 2 1.6 Electromagnetic radiation 2 1.7 Mechanical movement 2 1.8 Emissions 2 1.9 Hot surface 2 1.10 Transport 2 1.11 Storage 3 2. INTENDED USE 4 3. TECHNICAL DATA 4 3.1 Product drawing 5 3.2 Nominal data 5 3.3 Data according to Commission Regulation (EU) 327/2011 5 3.4 Technical description 6 3.5 Mounting data 6 3.6 Transport and storage conditions 6 3.7 Electromagnetic compatibility 6 4. CONNECTION AND STARTUP 6 4.1 Mechanical connection 7 4.2 Electrical connection 8 4.3 Connection in terminal box 8 4.4 Factory settings 9 4.5 Connection diagram 11 4.6 Checking connections 11 4.7 Switching on the device 11 4.8 Switching off the device 11 5. INTEGRATED PROTECTIVE FEATURES 12 6. MAINTENANCE, MALFUNCTIONS, POSSIBLE CAUSES AND REMEDIES 12 6.1 Vibration testing 12 6.2 Cleaning 13 6.3 Safety inspection 13 6.4 Disposal Item no. 51800-5-9970 · ENU · Change 212946 · Approved 2020-07-14 · Page 1 / 14 ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com