Edelbrock 1207* Manuals

1 of 3 Edelbrock Air Cleaner Brochure #63-0019 ©2014 Edelbrock LLC Rev. 2/13/14 QT/mc EDELBROCK AIR CLEANER Part Numbers: 1207, 1208, 1209, 1221, 1222, 1235, 1236, 4207, 4208, 4210, 4220- 4237, 4239, 41613, 42203 INSTALLATION INSTRUCTIONS Please study these instructions carefully before installing your new Air Cleaner Assemblies. If you have any questions, do not hesitate to contact our Technical Hotline at: (800) 416-8628 from 7:00 am to 5:00 pm, Monday through Friday, Pacific Standard Time. DESCRIPTION: Edelbrock Air Cleaner Assemblies - Due to the many different applications of the Edelbrock air filters, some modifications maybe required. INSTALLATION INSTRUCTIONS: 1. Install suitable air horn gasket and carburetor stud (not supplied) on carburetor(s) and place air cleaner base over carburetor. 2. For single carb models with dual carb tops, thread the special bracket on the carb stud until the two studs protrude through the top of the air cleaner by about 1/2”. Bracket must be positioned to clear carburetor choke linkage and choke plate. 3. Install filter and air cleaner lid, checking for clearance between the carb stud and lid. Trim carb stud, if necessary. For carburetors with tall bowl vent tubes, it may be necessary to purchase Edelbrock air cleaner spacer #8092. Vent tube to air cleaner clearance should be no less than 1/8”. Note: To prevent possible hood damage, check for proper hood clearance using clay cones as seen in Figure #1. Don’t shut the hood without checking clearance first! CRANKCASE VENTILATION: Some applications may require a Crankcase Ventilation Adapter #1205 (sold separately) that mounts to the lower side of the air cleaner per the recess seen in Figure #2. This Crankcase Ventilation Adapter can be purchased at your local Edelbrock retailer. 1. If you wish to use the crankcase ventilation adapter, drill two ¼” bolt holes (A) in the recessed area at the rear of the air cleaner base, then drill a few ¼” holes (B) in the larger recess window to allow the fitting to breath (See Figure #2). Bolt the fitting to the base with the ¼” nuts, bolts, and washers included with #1205. Be sure to de-burr drilled holes before installing the adapter. 2. Check for clearance between linkages and the ventilation adapter and rotate the air cleaner base as necessary. MAINTENANCE: Some air cleaner assemblies have a pre-oiled gauze element, that can be cleaned and re-oiled as needed to improve its air flow. Simply wash the element in hot soapy water and allow to dry, then apply a light aerosol oil. Replacement pre-oiled gauze elements (Edelbrock #1220) are available through your dealer. Replacement knurled nuts for Elite Series Oval Air Cleaners are available as Edelbrock #4219. The gauze elements are dark in color when shipped and the paper elements are white in color. Do not attempt to wash the paper type elements. HOOD CLEARANCE FORWARD A B C D E CLAY CONES Figure #1 Figure #2 Edelbrock LLC • 2700 California St. • Torrance, CA 90503 Tech Line: 800-416-8628 ®

INSTALLATION INSTRUCTIONS Edelbrock Air Cleaner Assemblies Catalog #1207*, 1208, 1209, 1221*, 1222* #4207*, 4210, 4221*, 4222*, 4223*, 4224*, 4235 § If you have any questions or problems, please call our Technical Hotline at: 1-800-416-8628, 7:00 am – 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at [email protected]. § DESCRIPTION: Edelbrock Air Cleaner Assemblies - Due to the many different applications of the Edelbrock air filters, some modifications maybe required. The part numbers listed above with asterisks (*) come with a crankcase ventilation adapter. INSTALLATION INSTRUCTIONS Note: Some Air cleaner kits include the crankcase ventilation adapter, that adapts to the lower side of the air cleaner per the recess seen in figure #1 (Crankcase ventilation adapter #1205). Other kits may not be applicable. 1. If you wish to use the crankcase ventilation hose fitting, drill two ¼” bolt holes (A) in the recessed area at the rear of the air cleaner base, then drill several ¼” holes (B) in the larger recess to allow the fitting to breath (See figure #1). Bolt the fitting to the base with the ¼” nuts, bolts, and washers. Be sure to de-burr drilled holes. 2. Install air horn gasket and carburetor stud on the carburetor and place air cleaner base over carburetor. 3. Install filter and air cleaner lid with wing nut. Check for clearance between the carburetor stud and hood before closing hood. Trim carburetor stud as needed. PLEASE complete and mail your warranty card. Be sure to write the model number of this product in the “Part #_________” space. THANK YOU. Edelbrock Corporation••2700 California Street•• Torrance, California 90503 2001 Edelbrock Corporation Rev. 8/01 Brochure No. 63-0019 A A Figure # 1 B