EGAN VersaBoard Mounting Kit Manuals

� To create the top mount assembly, place panel brackets on top mount brackets, so that the top mount bolt fits into the panel bracket slot. Screw the thumbscrew onto the bolt loosely. � Slide a top mount assembly onto each top corner mount. � Carefully lift the assembly over the top of the cubicle or panel. Adjust the brackets to a comfortable fit, and gently tighten screws. Corner Mounts (rear view, left & right) � � � Each VersaBoard Top Kit includes: 2 Left Corner Mounts, 2 Right Corner Mounts 2 Rubber Standoffs, 2 Panel Brackets 2 Thumbscrews 2 Top Mount Brackets* *Top Mount Brackets are available in 3 different sizes to accommodate from 2” up to 5-5/8” systems. To order more markers, EganCloths, kits, or other accessories: 1-800-263-2387 www.egan.com Rubber Standoffs Thumbscrews Panel Bracket Panel Bracket Slot Top Mount Bolt Top Mount Bracket Top Mount Assembly Top Corner Mount Thumbscrew International +1-905-851-2826 Egan Visual Inc. 1-800-263-2387 email: [email protected] www.egan.com VersaBoard Top Kit #024H500_r4 01/05:50 © 2005 Egan Visual Inc. Printed in Canada. All Rights Reserved. Specifications are subject to change without notice. This document is available online at www.egan.com/docs/024H500_r5.pdf VersaBoard Track Kit � With the corner track mounts and track bumpers installed, place the VersaBoard onto the track. Track not included. For track installation, refer to your Track Assembly Instructions. Track Mounts (left & right) Track Bumpers (left & right) � Each VersaBoard Track Kit includes: 2 Track Mounts, 2 Track Bumpers (Track not included) Track Mount Track V E R S A B O A R D M O U N T I N G K I T I N S T R U C T I O N S Any way you look at it, easy-to-use mounting kits are the secret to Egan VersaBoard versatility. There are two types of VersaBoard corner mounts: (A) corner mounts & bumpers for Track installation, and (B) corners for Edge/Top/Wall mounting. They are always installed onto the board horizontally. Each corner mount has a channel guide. When the guide lines up with the channel on the permanent corner block, the corner mount slides on easily. They are designed to fit snugly, so push until you feel the mount lock, to ensure it’s firmly attached. To remove, grip corner mount firmly and pull it away from the VersaBoard, horizontally. Wiggling the mount up and down as you pull will assist in removing the snug-fitting mounts. HOW TO INSTALL CORNER MOUNTS Permanent Corner Block Channel Channel Guides Track Corner Bumper Corner Mount Assembly for Track Kits. Attach the track corner mounts and track corner bumpers, as shown above, before mounting. Note: Prior to this step, corner mounts and bumpers should already be installed on the VersaBoard. EganMarkers Red, green, black, brown By the dozen: all one color, or 3 of each EganCloth™ Fabulous 16” x 12” washable cloth great for any whiteboard 5-YEAR LIMITED WARRANTY Egan warrants the construction and components of its VersaBoard products for normal and reasonable use for a period of five years from the date of invoice. The Egan VersaBoard is backed by quality construction, including a honeycomb core lamination and a low-glare (EVS™) writing surface. The EVS writing surface has a 5-year limited warranty, provided that proper care and maintenance have been maintained. The use of harsh cleaners, permanent markers, paint, low quality dry-erase markers, and other abuse, may damage the surface and may void any warranty. The EganCloth® is recommended as the best product to use to clean the EVS surface. This warranty does not apply to defects resulting from negligence, damage from sharp objects, lack of proper care and maintenance. All decisions of workmanship, failure, misuse, and abuse remain with the manufacturer. Items may only be returned with prepaid shipping, and with Egan Visual Inc.’s prior written consent. VersaBoard Brackets: Brackets supplied are intended for use to support the two specified sizes of VersaBoards in a typical office application. They are not intended or guaranteed for use with any other Egan Visual products. No warranties other than those contained herein shall be applied. Note: Prior to this step, track mounts and track bumpers should already be installed on the VersaBoard. Top Mount Brackets Panel Brackets Top Bottom V E R S A B O A R D M O U N T I N G K I T I N S T R U C T I O N S � Remove adhesive backer, and apply friction pad to edge bracket (adhesive-side to bottom of edge bracket). � Slide assembled brackets onto back of top corner mounts. � With edge brackets in place, position VersaBoard on a 90° edge (file cabinets, tables). Edge Brackets Friction Pads Corner Mounts (rear view, left & right) � � � Each VersaBoard Edge Kit includes: 2 Left Corner Mounts, 2 Right Corner Mounts 2 Rubber Standoffs, 2 Edge Brackets, 2 Friction Pads Rubber Standoffs Corner Mount Edge Bracket Top Corner Mount (front view) Friction Pad VersaBoard Edge Kit • Place the VersaBoard on a flat surface, or upright on the floor, in the orientation in which it will hang. • Attach Rubber Standoffs to a left and right corner mount to create two bottom corner bumpers (see details below). • Slide bottom bumpers onto board first, then top corner mounts, as shown above; refer to the appropriate kit mounting instructions. VersaBoard corner mounts are designed to slide on easily – change from a vertical board to a horizontal board in a SNAP! Select a left and right corner mount and attach the rubber standoffs to convert them to bottom bumpers (to protect walls and to prevent board from moving when in use). Note: Standoffs have a groove that fits into a slot on the back of each corner mount. Proper attachment ensures a secure board. HOW TO BUILD A CORNER BUMPER � Slide the wall mount brackets onto the top corner mounts of the VersaBoard. � Position board at desired location on wall, ensure it’s level, and apply pressure firmly against top left and right corner mounts. The positioning pins on the back of each wall mount bracket will leave a dimpled impression on the wall. Remove the wall mount brackets from the corner mounts. � Position each wall mount bracket so that the positioning pins rest in the impressions marked on the wall in Step B. Use a screw (#8 maximum) or suitable hardware to fasten each bracket to the wall. � Slide the VersaBoard down onto the wall mount brackets. Bottom Corner Mounts (left & right) (rear view) � � � � � � Each VersaBoard Wall Kit includes: 2 Top Corner Mounts (left and right) 2 Bottom Corner Mounts (left and right) 2 Rubber Standoffs, 2 Wall Mount Brackets What you’ll need to have on hand: 2 Screws (maximum size: #8) or suitable fastening hardware Appropriate screwdriver and a level Wall Mount Brackets Positioning Pins Wall Mount Bracket (rear view) Wall Mount Bracket (front view) Wall Mount Bracket (front view) Top Corner Mount VersaBoard Wall Kit Corner Mount Assembly for Edge, Top & Wall Kits. Attach the corner mounts and bumpers, as shown above, before mounting. WARNING: This option is intended for use in areas that experience a minimum (to zero) walk-by traffic. If you anticipate traffic or movement, it is recommended that you use an adhesive such as double-sided tape or Velcro® to secure the Edge Mount Assembly to the resting surface. Rubber Standoffs Rubber Standoff Adhesive side Note: Prior to this step, corner mounts and bumpers should already be installed on the VersaBoard. Note: Prior to this step, corner mounts and bumpers should already be installed on the VersaBoard. Warning: Wall Mount is considered permanent, ensure that you have positioned the board accurately prior to installation. Installer to provide fastening hardware best suited to wall type and board weight. Side View ATTACHING THE OPTIONAL PEN TRAY � Turn the VersaBoard and the pen tray upside down. � Squeeze the ends of the cloth tray � and marker tray � toward each other to widen the clasp area �. � Ease the pen tray onto the bottom frame of the board until it snaps into place. Turn the board upright and place on mounting brackets. Pen Tray sold separately. Pen Tray (upside down) VersaBoard (upside down) Cloth Tray Pen Tray Marker Tray � Don’t forget, you can also use the pen tray as a carry-handle � � � Top Bottom Top Left Corner Mount Top Right Corner Mount