Electrolux E23BC68JSS Manuals

iCE MAKER INFORMATION Test Cycling Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until holding switch circuit is completed. All components of ice maker should function to complete the cycle. Water Fill Volume The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 102 to 130cc (3.4 to 4.3 oz.). When a water valve is replaced, the fill volume must be checked. T U R N Mounting Plate Screws Mounting Plate Screw Motor Gear Timing Gear Water Fill Adjustment PERFORMANCE DATA NO LOAD & NO DOOR OPENINGS AT 37°/0° CONTROL SETTING (2500++ V4 CONTROLS) Variable Speed Compressor 65°F (18°C) Ambient 90°F (32°C) Ambient Operating Time 32 to 40% 100% Freezer Temperature -6° to 6° F -21° to -14° C -6° to 6° F -21° to -14° C Refrigerator Temperature 33° to 46° F 0.5° to 8° C 33° to 46° F 0.5° to 8° C Low Side Pressure (cut-in) 5 to 12 psig 34 to 83 kPa N/A Low Side Pressure (cut-out) -2 to 2 psig -14 to 14 kPa -2 to 2 psig -14 to 14 kPa High Side Pressure 85 to 95 psig 586 to 655 kPa 120 to 135 psig 827 to 931 kPa Wattage 40 to 55 60 to 70 Amps (running) .5 to 1.1 .7 to .9 Base Voltage 115 vac (127 vac max) DEFROST SPECIFICATIONS Cabinet Size Thermostat Heater Cut-in Cut-out Watts Ohms 23’ SD, 28’ SD, 23’ CD 25° F (-4° C) 47° F (8° C) 500 26 Electronic Timer - (ADC) Defrost 24 minutes every 6-96 hours of compressor run time. CONDENSER FAN MOTOR Watts RPM Amps 3.1 (Energy Star, some models) 1100 CW Opposite Shaft 0.03 Running ICE MAKER SPECIFICATIONS Electrical 115 vac (127 vac max) Thermostat Opens at 48° F (9° C), Closes at 15° F (-9° C) Heater Voltage 85 vac ICE MAKER CONNECTOR PLUG CONNECTIONS Wire Number Wire Color Connects to: 1 Green/Yellow Ground 2 Yellow Water Valve 3 Black Line 4 Light Blue Neutral NOTE This product comes equipped with an Adaptive Defrost Control (ADC). To activate manual defrost, simultaneously press and hold the Fresh Food up (+) and Fresh Food down (-) keys for 5 seconds. A “d” in the freezer temperature window and “F” in the refrigerator temperature window will display when the heater is activated. To deactivate manual defrost, simultaneously press and hold the Fresh Food up (+) and Fresh Food down (-) keys for 5 seconds. A “d” and “F” will be displayed until the defrost cycle is complete. SERVICE DATA SHEET - 242062500 FREEZER ICE MAKER - AUTOMATIC DEFROST BOTTOM FREEZER - R134a IMPORTANT SAFETY NOTE The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing this appliance. IMPORTANT If any green grounding wires are removed during servicing, they must be returned to their original position and properly secured. CAUTION All electrical parts and wiring must be shielded from torch flame. DO NOT allow torch to touch insulation; it will char at 200°F and flash ignite (burn) at 500°F. Excessive heat will distort the plastic liner. IMPORTANT PLEASE RETURN THIS SHEET TO IT’S ORIGINAL LOCATION POWER ICE MAKER ICE MAKER ICE MAKER WATER VALVE LINE THERMAL CUT-OUT HOLD SWITCH THERMOSTAT SHUT-OFF SWITCH WATER FILL SWITCH MOLD HEATER MOLD MOUNTING PLATE 165 WATTS MOTOR NEUTRAL BLK BLK BLK BLK BLU C C C NO NO NO NC NC NC YEL YEL BRN RED GRN / YEL GRN / YEL RED RED LT. BLUE LT. BLUE YEL P-3 P-1 P-2 P-4 ICE MAKER

DO NOT REMOVE this label until the refrigerator has been leveled. Please follow all instructions for leveling your refrigerator. P/N: 242046600 2 1 6 Doors  Handles are secure and tight  Door seals completely to cabinet on all sides  Fresh food doors are level Leveling  Refrigerator is level, side to side and tilted 1/4” front to back  Toe grille is properly attached to refrigerator  Cabinet is sitting solid on all corners Electrical Power  House power turned on  Refrigerator plugged in Installation Check List Preparing For Installation CAUTION Room temperatures below 55°F (13°C) or above 110°F (43°C) will impair cooling ability of your refrigerator’s compressor. NOTE If you need to remove the doors to get your refrigerator into the house, please refer to “Removing Doors” in the Use & Care Guide. These installation instructions are provided only as a possible customer option. Electrolux recommends that you use a service or kitchen contracting professional to install your refrigerator. IMPORTANT If you are installing your refrigerator without connecting it to a water supply, make sure the ice maker’s power switch is turned Off (see the Use & Care Guide for more details). WARNING To avoid electric shock, which can cause death or severe personal injury, do not connect your refrigerator to an electrical power source until you have completed Step 2 of these instructions. Be sure to coordinate site preparation and installation with your kitchen contractor. Include these minimum guidelines in your site preparation: • Choose a place near a grounded electrical outlet. • Do not use an extension cord or an adapter plug. • Avoid direct sunlight and close proximity to a range, dishwasher or other heat source. • Floor should be level and able to support a fully loaded refrigerator. • The refrigerator’s Ice Dispenser requires water supply access. • Plan for easy access to counter tops when removing food. • For complete access to drawers and freezer baskets, doors must be able to fully open. • Load refrigerator from side of cabinet only. • Do not run retaining straps over handles nor over-tighten straps. • Never use refrigerator handles to move the refrigerator. Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top: 3/8 inch / Rear: 1 inch NOTE Please call 1-877-435-3287 if you need assistance with this installation. CAUTION • Shifting the refrigerator from side to side may damage flooring. • Do not block the toe grille on the lower front of your refrigerator. Sufficient air circulation is essential for proper operation. Level Refrigerator & Adjust Doors (if necessary) 5 Electrolux uses packing foam and tape to secure the internal parts of your refrigerator for shipping. Once the refrigerator is in position, you can remove this material. What’s Next? Congratulations! You are ready to begin enjoying your new Electrolux refrigerator. • For important safety instructions and to learn how to operate your refrigerator, please read the entire Use & Care Guide. • You may want to start with the “Normal Operating Sights & Sounds” section of the Guide to learn what to expect during typical operation. • Please register your product. You can register online at www.electroluxappliances.com. or you can simply send in the Registration Card. Guidelines for final positioning of your refrigerator • All four corners of the cabinet must rest firmly on the floor. • The sides should tilt ¼ inch from front to back (to ensure that doors close and seal properly). • Doors should align with each other and be level. Most of these conditions can be met by raising or lowering the adjustable front rollers. To level the cabinet using the front rollers: 1 You can raise or lower each door. Use a 3/8 inch socket wrench to turn the adjustment screws (1 per side). To raise: turn adjustment screw clockwise. To lower: turn adjustment screw counterclockwise. 2 Ensure both doors are bind-free with their seals touching the cabinet on all four sides and that cabinet is stable. 3 After unit is leveled, lower anti-tip leg until it contacts the floor. To Connect Water Supply Line To Ice Maker Inlet Valve 1. Disconnect refrigerator from electric power source. 2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shutoff valve. 3. Remove plastic cap from water valve inlet and discard cap. 4. If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto water supply line. Push water supply line into water valve inlet as far as it will go (¼ inch). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 1. If you use stainless steel tubing - The nut and ferrule are already assembled on the tubing. Slide compression nut onto valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 2. 5. With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown. 6. Coil excess water supply line (copper tubing only), about 2½ turns, behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface. 7. Turn ON water supply at shutoff valve and tighten any connections that leak. 8. Reconnect refrigerator to electrical power source. 9. To turn ice maker on, lower wire signal arm (side mounted) or set the ice maker’s On/Off power switch to the “I” position (rear mounted). Before Installing The Water Supply Line, You Will Need: • Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver • Access to a household cold water line with water pressure between 30 and 100 psi. • A water supply line made of ¼ inch OD, copper or stainless steel tubing. To determine the length of tubing needed, measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet, so the refrigerator can be moved out for cleaning. • A shutoff valve to connect the water supply line to your household water system. DO NOT use a self- piercing type shutoff valve. • A compression nut and ferrule (sleeve) for connecting a copper water supply line to the ice maker inlet valve. WARNING To avoid electric shock, which can cause death or severe personal in- jury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator. CAUTION To Avoid Property Damage: • Copper or Stainless Steel braided tubing is recommended for the water supply line. Water supply tubing made of ¼ inch plastic is not recommended to be used. Plastic tubing greatly increases the potential for water leaks, and the manufacturer will not be responsible for any damage if plastic tubing is used for the supply line. • DO NOT install water supply tubing in areas where temperatures fall below freezing. • Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly. NOTE Check with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator. Depending on your local/state building codes, Electrolux recommends for homes with existing valves its Smart Choice® water line kit 5305513409 (with a 6 ft. Stainless Steel Water Line) and for homes without an existing valve, Electrolux recommends its Smart Choice water® line kit 5305510264 (with a 20 ft. Copper Water Line with self-tapping saddle valve). Please refer to www. electroluxappliances.com for more information. Copper water line from household water supply (Include enough tubing in loop to allow moving refrigerator out for cleaning.) Ferrule (Sleeve) Copper water line Water Valve Valve Inlet Water Valve Bracket Steel Clamp Plastic Water Tubing to Ice Maker Fill Tube Brass Compression Nut Figure 1 Figure 2 *Please refer to your Use & Care Guide for more details. Connect Water Supply Ice Maker  House water supply connected to refrigerator  No water leaks present at all connections  Ice Maker is turned ON. Final Checks  Shipping material removed  Fresh Food and Freezer temperatures set 3 Raise Lower Anti-tip Leg Door Door If you are not satisfied with the installation of your refrigerator, please contact the store you purchased it from or call 1-877-435-3287 for assistance. NOTE DO NOT remove center screw from freezer drawer. This is a factory adjustment. Drawer Screw Drawer Screw Drawer Screw Drawer Screw Leveling Freezer Drawer (if necessary) 1. Check gasket seal around top, bottom, and sides of freezer drawer. 2. If gasket is not sealed, open drawer and slightly loosen 4 drawer screws (2 on each side) to allow drawer to rotate. 3. Close drawer and recheck the seal on the gasket (A). Open the drawer grabbing by the sides in the center (B). Be careful not to rotate the drawer. 4. Tighten 4 drawer screws. 5. Recheck gasket seal. 6. Install the toe grille by fitting into place. Raising/Lowering Door Remove Screw Open Door 90 degrees Bottom of Door A B Remove Screw Doors final adjustment using the adjustable lower hinge (select models, if necessary): 1 Open doors to 90 degrees. 2 Remove screw. 3 Lift the door while adjusting the washer. To raise the door: rotate washer clockwise. To lower the door: rotate washer counter-clockwise. 4 Replace the screw, ensuring it is between the spokes of the hinge washer. Screw will not be tight, just insert until it is flush with the hinge. NOTE If after adjusting doors higher the door makes a popping/clicking sound, remove screw and replace with the longer one provided. Pull Drawer Out From Both Sides Grab Drawer At Center Then Push Against Freezer Drawer A B 4 Remove Internal Shipping Materials Installation Instructions* for French Door Bottom Freezer/Refrigerator

241978401 June 2009 Use & Care Guide French Door Bottom Freezer/Refrigerator Guia de Uso y Cuidado Refrigerador con congelador inferior de puerta doble Guide d’utilisation et d’entretien Réfrigérateur à portes françaises/Congélateur en bas