Elkay EFC1150D-A Manuals

ELKAY Central Water Filtration System EFC1150D-A & EFC1150D-B Please read all instructions, specifi cations, and precautions before installing and using your water fi lter system. Page 1 1000003995 (Rev A - 05/2017) A) Central Water Filtration System B) Drain fi tting with clip C) Hose clamp D) Drain hose/2m E) Bypass valve F) Power supply adapter G) Flow meter H) Clamping brackets I) Clamping bracket screws (2) J) Hoses K) Silicone oil L) Nylon band M) Installation and User Manual N) Small parts pack - 2 screws - 1 large o-ring - 1 small o-ring SPECIFICATIONS Working pressure 0.15MPa-0.4MPa Inlet temperature 5-38°C Power input EFC1150D-A: 220V/50Hz EFC1150D-B: 220V/60Hz Output 24V 500mA Rated fl ow* 1500L/h Rated throughput* 120,000L** Net weight (excluding water) 28kg Filter activated carbon 13.7kg Quartz sand 5kg Inlet/outlet pipe connection 3/4 inch Drain connection 1/2 inch * System performance will vary based on water quality and environmental conditions. ** 120,000L for chlorine, taste, and odor. 40,000L for lead, cadmium, copper, sulfate, and nitrite. 11.7“ (297mm) 3.5“ (88.5mm) 42.9“ (1090mm) 16.4“ (416mm) PARTS LIST Page 2 1000003995 (Rev A - 05/2017) A G H E D J L F B C K I 37.8“ (961mm) Notice Do not use with water that is microbiologically unsafe or of unknown quality. Filter housing must be protected against freezing temperatures, frost, snow, sleet, ice, high temperature, and direct sunlight. Exposure to these elements can cause damage and product failures. DO NOT install outdoors or in a wet environment. Moisture can cause the system electronics to malfunction. • For cold water use only. Do not use on hot water line. • Make certain that installation complies with all state and local laws and regulations. • After periods of non-use (such as during a vacation) it is recommended that you let the water run for 5–6 minutes before using. • Extended periods of nonuse (over six months) might require the replacement of the fi lter media for optimal performance. • In case of equipment fault or other special situations, you can use the bypass valve to bypass the system. This will provide your home with untreated water. • For use with grounded power only. Caution Caution Installation Requirements Ensure the installation position of the fi lter; the installation position will meet installation requirements. Wall Operation Panel Bypass-Valve Component Central Water Filtration System (Shortened version shown) Floor Floor Drain Page 3 1000003995 (Rev A - 05/2017) Power Supply Adapter Inlet Pipe G3/4” Exterior Thread Drain Hose Outlet Pipe G3/4” Exterior Thread Ball Valve Before Installation 1. Before installation, please check whether the valve head has come loose from the tank. 2. Open the upper cover by pulling up and then disconnecting the cable running to the electronic display. 3. Remove the three screws at the back of the unit and remove the rear cover. 4. Check the valve head for movement relative to the tank. If the valve head is loose, turn clockwise to tighten. Confi rm that the O-ring is not pinched between the tank and valve head. NOTE: This might require two people: one to hold the tank and another to turn the valve head. NOTE: The gap between the tank and valve head should be smaller the 0.5mm. 5. Re-install the rear cover using only the two lower screws. The upper screw is only used for shipping and should be discarded. NOTE: Do not re-install the top cover at this time. Installation 1. Insert the drain fi tting into the drain tube and secure with the hose clamp. 2. Install the drain fi tting into the drain connection on the valve head and secure with clip. Rear Cover Discard Top Screw Electronics Cable Valve Head O-ring Wrap with PTFE Tape Drain Fitting Hose Clamp Drain Tube Page 4 1000003995 (Rev A - 05/2017) Clip